Safety Instructions; Description And Specifications; Engineering Data; Piping - Suction - Goulds IRRI-GATOR GT07 Instruction Manual

SAFETY INSTRUCTIONS

TO AVOID SERIOUS OR FATAL PERSONAL INJURY
OR MAJOR PROPERTY DAMAGE, READ AND FOL-
LOW ALL SAFETY INSTRUCTIONS IN MANUAL AND
ON PUMP.
This is a SAFETY ALERT SYMBOL.
When you see this symbol on the pump or
in the manual, look for one of the follow-
ing signal words and be alert to the poten-
tial for personal injury or property damage.
Warns of hazards that WILL cause serious
DANGER
personal injury, death or major property
damage.
Warns of hazards that CAN cause serious
WARNING
personal injury, death or major property
damage.
Warns of hazards that CAN cause personal
CAUTION
injury or property damage.
NOTICE: Indicates special instructions which are very
important and must be followed.
THIS MANUAL IS INTENDED TO ASSIST IN THE
INSTALLATION AND OPERATION OF THIS UNIT
AND MUST BE KEPT WITH THE PUMP.
THOROUGHLY REVIEW ALL INSTRUCTIONS AND
WARNINGS PRIOR TO PERFORMING ANY WORK
ON THIS PUMP.
MAINTAIN ALL SAFETY DECALS.
NOTICE: INSPECT UNIT FOR DAMAGE AND RE-
PORT ALL DAMAGE TO THE CARRIER
OR DEALER IMMEDIATELY. DO NOT
USE PUMP IF DAMAGE IS SUSPECTED.
UNITS NOT DESIGNED FOR USE
WARNING
WITH HAZARDOUS LIQUIDS OR
FLAMMABLE GASES.
Hazardous Fluids
can cause fire,
burns or death.

DESCRIPTION AND SPECIFICATIONS

•
The Model GT embraces a line of end suction, single
stage, self-priming centrifugal pumps for lawn sprin-
kling, HVAC systems, and general water transfer.
•
Casing is cast iron construction with tapped openings
provided for vacuum gauge and casing drain.
Impellers are enclosed design, glass filled Noryl TM ,
•
threaded directly on motor shaft.
•
Standard motors are NEMA standard, 3500 RPM,
open drip proof enclosure.

ENGINEERING DATA

Model HP Ph/Hz
GT07 ¾
GT10 1
GT15 1½ 1/60
GT20 2
GT30 3
GT073 ¾
GT103 1
GT153 1½ 3/60
GT203 2
GT303 3
•
Maximum Liquid Temperature: 160ºF (71ºC)
•
Maximum Starts per Hour: 20 – evenly distributed
PIPING
•
Pump MUST be installed horizontally on a solid flat
surface, with discharge on top.
•
Allow adequate space for servicing and ventilation.
Protect the unit from weather and water damage due
to rain or flooding or freezing temperatures.
•
Piping should be no smaller than the suction and dis-
charge connections and kept short as possible, avoiding
unnecessary fittings to minimize friction losses.
•
All piping MUST be independently supported and
MUST NOT place any piping loads on the pump.
NOTICE: DO NOT FORCE PIPING INTO PLACE AT
PUMP SUCTION AND DISCHARGE CON-
NECTIONS.
•
All pipe joints MUST be airtight.
The use of Teflon TM tape, or equivalent, is recom-
•
mended for ALL pipe joints.
SUCTION
•
Total suction lift, including elevation and pipe friction
loss, should not exceed 25 feet of head.
•
Install an airtight union in the suction line close to the
pump. See Figure 1.
•
Installation of a foot valve at liquid source is recom-
mended.
NOTICE: FOR INSTALLATIONS WITH LONG SUC-
TION PIPING, BOTH A FOOT VALVE
AND A CHECK VALVE ARE RECOM-
MENDED.
•
To avoid air pockets, no part of the piping should be
above the pump suction connection and piping should
slope upward from liquid source.
•
For installations with long suction piping, fill the suc-
tion pipe with water before connecting to pump.

DISCHARGE

•
Install a tee at the discharge connection of the pump.
The top opening of the tee is required for initial prim-
ing. See Figure 1.
Suction Discharge Wt. lbs.
48
52
60
65
76
1½" NPT 1½" NPT
49
52
55
69
71
3