1. Manuals
  2. Brands
  3. Remotec Manuals
  4. Thermostat
  5. ZTS-110 Z-Thermostat
  6. User manual

Remotec ZTS-110 User Manual

Z-thermostat
Hide thumbs Also See for ZTS-110:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
Enlarged version
WARRANTY
ONE-YEAR LIMITED WARRANTY: Remotec warrants this product to be free from defects in
materials and workmanship under normal use and service for a period of one year from the
original date of purchase from the distributor or dealer.
REMOTEC shall not be liable for:
- Damages caused by defective devices for indirect, incidental, special, consequential or
punitive damages, including, inter alia, loss of profits, savings, data, loss of benefits, claims
by third parties and any property damage or personal injuries arising from or related to the
use of the device.
- Service trips to provide instruction on product use.
- Shipping costs for replacement products.
This warranty is limited to the repair or replacement of this product only, if the purchase date
cannot be substantiated, the warranty period will begin on the date of manufacture as indicated
on this product. All warranty claims must be made to Remotec appointed distributors or dealers
during the applicable warranty period. This warranty gives you specific legal right and you may
also have other rights which vary in each country.
www.remotec.com.hk
Printed in China
39
2/11/14
Revised on 2/13/14
Revised on 2/14/14
F820-8031-0003
ZTS-110
Z-Thermostat
USER MANUAL

Advertisement

Table of Contents
loading

Related Manuals for Remotec ZTS-110

Summary of Contents for Remotec ZTS-110

  • Page 1 All warranty claims must be made to Remotec appointed distributors or dealers during the applicable warranty period. This warranty gives you specific legal right and you may also have other rights which vary in each country.

  • Page 2: Table Of Contents

    Setup and Operations Product Overview Also, you can use the ZTS-110 to control / check your room temperature by smart Description of Function Keys phone or PC while you are at home or outside through Z-Wave gateway.

  • Page 3: Features List Glossary

    Features List Glossary HVAC System Type Compatible: Devices and nodes are all terms to describe an individual Z-Wave - Standard (gas/electric) or Heat Pump Device or Node device. These are all interchangeable when setting up your Z-Wave Multistage System Compatible: network.

  • Page 4: Physical Installation And Wiring

    Physically Installing the Thermostat - Turn off ZTS-110 and the electronic devices (e.g. heater, cooler) which will 1. Open the ZTS-110 by pulling the two sections apart (Figure 2). Use the fingertips be connected and the electric source before installation and maintenance.

  • Page 5: Wiring

    When wiring split systems, wire the heating systems "24Vac Power" (red wire) to - When there is a cooling request, thermostat will turn on Y HPUMP the ZTS-110 "RH" terminal, and wire the cooling systems "24Vac Power" to the Set to HPUMP for heat pump system ELECTH ZTS-110 "RC"...

  • Page 6: Product Overview

    Setup and Operations Activate/Deactivate Easy Mode The ZTS-110 is default with Easy mode, below illustrates the functions of Easy Product Overview mode: - Active functions: Change Mode, change Fan mode and Temperature Scale Figure 6. ZTS-110 selection - Inactive functions: Scheduling, Program Mode, Clock Display, Setting Time,...

  • Page 7: Setting Mode

    Note: If you deactivated the Easy mode, you can continue to set up Day, Clock, 12/24 If you deactivated the Easy mode, please refer to Setting Mode for the temperature hour, F/C, Swing and Differential. Refer to below for steps: scale selection.
  • Page 8 Step Procedure / Description LCD indication Step Procedure / Description LCD indication Press "Prog" key once to confirm the setting and it will go to minutes setting. Press "Prog" key once to confirm the setting Minutes will keep flashing, press Up/Down and it will go to Advanced Recovery setting.

  • Page 9: Change Mode

    COOL Mode: thermostat controls the temperature according to the following Change Mode diagram Note: In Heat mode =>it displays "HEAT" if ELECTH is selected during jumper Output setting. Set point => it displays "HEAT PUMP" if HPUMP is selected during jumper setting.

  • Page 10: Change Fan Mode

    Change Fan Mode Override/Permanent Override Note: Override/Permanent Override is only available in HEAT, COOL or AUTO Step Procedure / Description LCD indication mode. Press "Fan" key once to change the Fan Step Procedure / Description LCD indication mode: FAN AUTO -> FAN ON WAKE Press "Prog"...

  • Page 11: Setting Schedule

    Setting Schedule Step Procedure / Description LCD indication MO TU WE TH FR WAKE Pre-defined Schedule (disabled by default): Event Time Heat Cool WAKE 6:00AM 70 F (21 C) 78 F (26 C) AWAY 8:00AM 62 F (17 C) 85 F (29 C) AWAY HOME 6:00PM...

  • Page 12: Battery Low Indication

    Procedure / Description LCD indication the time needed to adjust the temperature to the next program setting. When the ZTS-110 thermostat will detect the battery WAKE thermostat is in Advanced Recovery mode, level every 30 minutes; Battery low icon will the display will show "RECOVERY".

  • Page 13: Filter Counter

    FLiRS mode is targeted for battery operated applications and will enter sleep Home page. mode frequently in order to save battery life. ZTS-110 can't act as a repeater in this mode. The response to Z-Wave command is not as quick as Always WAKE Listening Device.

  • Page 14: Check Flirs / Always Listening Mode In Zts-110

    Z-Wave network; change Z-Wave operation mode. d) After Z-Wave inclusion process, if you reset ZTS-110 to default while both - If the LCD displays "AC", the unit is 24Vac and batteries are applied, ZTS-110 will take 24Vac as primary power...
  • Page 15 Symbol Inclusion and Exclusion Mode Key Description - After ZTS-110 is included to Z-Wave network, it will stay in Easy mode by default. Add (Include) / Delete (Exclude) - You can enable or disable Easy mode by local "Setting Mode" or Z-Wave parameter number 8.

  • Page 16: Support For Association Groups

    ZTS-110 will trigger AUTO report function if one of below status is changed. I. Operation mode (Off, Heat, Cool, Auto) II. Operation state (Heat on or off, Cool on or off) III.
  • Page 17 Functions Parameter No. Parameter value range Functions Parameter No. Parameter value range Report filter counter 0 (0x00) = disable AUTO report function. 4 (0x04) 0 (0x0000) to 9999 (0x270F) hours (read only) (by time interval) AUTO report timer: 0 (0x00) = C Scale of temperature 5 (0x05) 1 (0x01) = 0.5 hr...

  • Page 18: Reset Zts-110 To Factory Default Settings

    Reset ZTS-110 to Factory Default Settings Example for sensor temperature calibration: reading temperature (77 F) + (-2 F) Step Procedure / Description LCD indication Functions Parameter No. Parameter value range Sensor temperature 13 (0x0D) -2 (0xFE) = -2 F (-1.0 C) calibration Press and hold "Fan"...

  • Page 19: Frequently Asked Questions

    32 - 99 F / 0 - 40 C measurable range Temperature display Q Can I use 2 or more ZTS-110 in my house? What is the max. units if yes? 0.5 F / 0.1 C resolution A Yes and it is very depends on the capability of gateway / controller. For example, Temperature Setting gateway can supports up to 8, 16 or 32 ZTS-110 in a network.

  • Page 20: Checking Accessories

    - There is no user serviceable parts in this unit. - ZTS-110: Z-Thermostat Caution - Screw + Wall Anchor x 4pcs - Risk of explosion if battery is replaced by an incorrect type.

Table of Contents