Yaesu FT-1000MP Operating Manual page 84

CAT System Computer Control
Legend:
Send all commands in the order shown! Commands that duplicate a front panel button are named
with all caps or else have their key displayed. Parameter variables are labeled with letters, while "-"
indicates a padding byte. Value is unimportant, but it must be present to pad the block out to five bytes.
Opcode
5th
Parameter Description
Parameter Bytes
Command
EDSP Settings (continued from previous page), P2
=
:
1st
CW 60 Hz BWF (47H), where P I
=
Fcenter (BCD format)
I 1
3rd 2nd
Data Mode AF Filter On (48H), where P1 =
FSK (1 OH), SSTV(2OH), Packet (30H), or FAX (40H).
4th
Random Noise Filter (4AH) Off / On (PI =00H / 1 YH)
I I
1
EDSP
/ / I / 1
Auto Notch Filter (4BH) Off / On (PI
=
O O H / 10H)
11
Enhanced
Digital
Signal
Processing
(Continued from
previous page)
\
75H
USB EDSP Modulation (B2H), with audio response of:
100 HZ-3.1 kHz (PI = I OH), 150 HZ-3.1 kHz (PI =20H),
200 HZ-3. 1 kHz (PI =30H), 300 HZ-3. 1 kHz (PI =40H)
AF Equalization (4EH), where P I
=
Off (OOH),
Bank 1 (1 OH), Bank 2 (20H), Bank 3 (30H), or Bank 4 (40H).
Tx EDSP OFF (BOH)
LSB EDSP Modulation (B3H), with audio response of:
100 HZ-3.1 kHz (PI -1 OH), 150 HZ-3.1 kHz (PI =20H),
200 HZ-3.1 kHz (PI =30H), 300 HZ-3.1 kHz (P1=40H)
Mic. Audio Equalization (61 H), where P1 = Off (OOH),
Bank 1 (1 OH), Bank 2 (20H), Bank 3 (30H), or Bank 4 (40H).
I /
TUNER
1
-
I
- -
1
-
1
T
1
81 H
I
Switch antenna tuner On (T=O1 H) or Off (T=OOH)
I
/ /
Tuner start
I
-
/
-
/
--
I
-
82H
1
Start antenna tuner
1 1
1
Dual Operation
(
-
I
-
/
-
/
D
1
83H
1
Switch dual receive On (D= 01 H) or Off (D=OOH)
1 1
- - -
R 84H
i l
Set SUB VFO-B
Operating Freq.
Seiect simplex operation (R=OOH), -shift (R=O1 H),
or +shift (R=O2H) for repeater operation.
85H
8AH
I
Enter new operating frequency in FI
-
F4, in BCD format:
see text for example.
Copy data displayed in VFO-A to VFO-B
Select filter bandwidth for selected IF (see below):
2nd & 3rd IF
Filter Selection
8CH
I
Memory Channel
Scan Skip
6.0 K X4=09 THRU X4=84 both X1=00
2.4 K X4=00 2.4 K X4=80 VFO-A X1=01
2.0 K X4=01 2.0K X4=81 VFO-B X1=02
500 Hz X4=02 500 Hz X4=82
250 Hz X4=03 250 Hz X4=83
Step VFO-A
I
UpIDown
8DH
8EH
I
Step frequency of VFO-A Up (T=OOH) or Down (T=O1 H)
I 1
Tag memory channels 1 thru 99 (X=OI -6CH), to be skipped
(S=OI H) or included (S=OOH) while scanning.
page
82