Safety Warnings - HellermannTyton Autotool System 3080 Assembly Instructions Manual

Hide thumbs Also See for Autotool System 3080:
Table of Contents

Advertisement

Available languages

Available languages

2 Safety warnings

2 .1 General power tool safety warnings
The safety warnings in the Operating instructions for the
ATS3080 also apply to operation of the ATS3080 after
installation of an automation system or device.
WARNING
Non-compliance with the safety warnings below can
lead to severe injuries, fire and electric shock .
f Comply with the instructions and warnings below.
f Keep the Operating instructions for the ATS3080 ready
to hand.
2 .2 Intended use
Use the Overhead suspension 3080 only when it is in full
working order and safe, always be safety-conscious and
aware of the hazards.
The Overhead suspension 3080 with integrated ATS3080
is suitable for and intended for the following uses:
• Semi automated binding of bundles up to a diameter of
max. 80 mm
• For indoor use only
• Industrial use
2 .3 Misuse
Use other than that stated in the section entitled
"Intended use" is misuse. The operating company
responsible for use of the Overhead suspension 3080
bears sole responsibility for injury and damage resulting
from misuse.
The safety regulations for the ATS3080 (see the
Operating Instructions for the ATS3080) apply in
addition.
The following are specifically prohibited:
• Use with faulty parts
• Use in explosive environments or in the presence of a fire
hazard
• Use outdoors
• Use in high humidity and/or direct sunlight
• Manipulation while processes are in progress
• Unauthorised alterations and modifications to the
Overhead suspension 3080 and its component parts
without the prior consent of HellermannTyton
• Use of spare parts and accessories not tested and
approved beforehand by HellermannTyton
2 .4 Personnel qualification
Underage persons and trainees are permitted to use the
device only under the supervision of an experienced
specialist and only with the express permission of the
operating company.
Assembly Instructions Overhead suspension 3080 • 03-2017 • v02 • 102-01013
2 .4 .1 Specialist personnel for operation
The tasks and authorisations assigned to specialist
personnel for extended operation are as follows:
• Operation of the ATS3080 and the
Overhead suspension 3080
• Rectification of faults or, as applicable, initiation of
measures for the rectification of faults
• Cleaning of the ATS3080 and the
Overhead suspension 3080
These individuals have the specialist training or practical
experience that will ensure correct handling.
2 .4 .2 Specialist personnel for maintenance and repair
Always have maintenance and repair work carried out by
duly qualified specialist personnel. These individuals have
received training that affords sufficient knowledge of the
ATS3080 or the Overhead suspension 3080 for them to
judge when it is in safe working order.
These individuals are also familiar with the following
rules and regulations:
• Applicable national health and safety regulations
• Accident prevention regulations
• Generally accepted codes of practice, regulations and
standards
2 .4 .3 Authorised person for low-voltage electrical
equipment
Work on the electrical supply and on parts that are live
when the device is in operation should always be carried
out by a person duly authorised to work on low-voltage
electrical equipment.
2 .4 .4 Authorised specialist for repair and testing
Only service technicians from HellermannTyton or service
technicians authorised by HellermannTyton are permitted
to carry out repairs and safety checks.
2 .5 Underlying hazards associated with use of the
ATS3080 or the Overhead suspension 3080
2 .5 .1 Electricity
f Always wear safety glasses and suitable safety
equipment whilst working.
f Before installation, cleaning and maintenance,
disconnect the ATS3080 and the Power pack 3080 from
the power supply.
2 .5 .2 Cleanliness at the workplace
Orderliness, good lighting and cleanliness at the
workplace all help to make work easier and to minimise
hazards and the risk of injury.
Always comply with the following principles of
orderliness and cleanliness at the workplace:
f Put tools away as soon as they are no longer needed.
f Avoid trips (e.g. immediately dispose of waste by placing
it in the containers provided for the purpose).
f Immediately remove spillages of grease, oil and other
liquids.
Safety warnings
5

Advertisement

Chapters

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Autotool System 3080 and is the answer not in the manual?

Subscribe to Our Youtube Channel

Table of Contents