Setting The Timer - Tiger JPB-G18S Operating Instructions Manual

6

Setting the Timer

3·6 1
4 5 7
Press twice for
rinse-free rice.
Using the Timer function (Timer 1 /
Timer 2)
You can preset the time that you want cooking
to be actually completed.
• Select either "Timer 1" or "Timer 2" and set the
desired completion time. The start of cooking will
be automatically adjusted so that the operation is
completed at the preset time.
• Each timer can be set to different times. e.g.
"Timer 1" for breakfast and "Timer 2" for dinner.
• The preset timer settings will be stored in
memory.
● Example setting: If "Timer 1" is set to 13:30,
cooking will be completed at 13:30.
1
Check the present time.
• See P.44 for the procedure to set the
present time.
Check the present time.
Blinks
20 20
2
Press the [Next] or [Back] key to
2
select the desired menu.
• It is not necessary to press the [Next] or
[Back] key if the desired menu is already
selected.
Check that the
Blinks
Keep Warm
lamp is off.
3
If you selected the "Porridge"
menu, use the [Hr] and [M] keys
to set the desired cooking time.
• Each time the [Hr] key is pressed, the set
time will increase by 5 minutes. Each time
the [M] key is pressed, that time will decrease
by 5 minutes.
• The cooking time can be set to any 5-minute
increment between 40 and 90 minutes.
Increases by
5 min.
• The default setting is for 60 minutes. Adjust
as desired.
4
Select the keep-warm setting for
after cooking. (See P.16.)
The keep-warm setting can be selected after
the timer setting.
5
Press the [Timer] key to select
either "Timer 1" or "Timer 2".
The selected setting will switch between
"Timer 1", "Timer 2" and "Soak Timer" each
time the [Timer] key is pressed.
• For the soak timer, see P.22.
Blinks
Beep
• The previously preset time will be displayed.
It is not necessary to set the timer again if the
desired completion time is already displayed.
Note
● The Timer function is not available in the following
Beep
cases.
• When the "Quick", "Mixed", "Sweet", "Slow
Cook" menu is selected
• When the preset time is less than that indicated
in the following table
Menu
Eco
Plain
Sushi
Porridge
Brown
Brown GABA
• When "0:00" is blinking on the display
• When the inner pot is not set.
● If the Keep Warm lamp is on, press the [Cancel]
key to turn off the lamp. (The Timer function is not
available while the Keep Warm lamp is on.)
● Setting a long time for the timer may form darker
Decreases
brown crisp rice. If this is not desired, rinse the
by 5 min.
rice well.
● If you do not operate the rice cooker within about
30 seconds after pressing the [Timer] key, an
alarm (3 beeps) will sound.
● If the [Timer] or [Start/Rinse-free] key is pressed
while the rice cooker is in a state where the Timer
function is not available, an alarm (3 beeps) will
sound.
6
Use the [Hr] and [M] keys to set
the desired completion time.
• The present time is displayed in a
24-hourformat.
Beep
Display
Press the [Hr] key to change the set time in
1-hour increments. Press the [M] key to
change that time in 10-minute increments.
Hold down the corresponding key to change
the time more rapidly.
Note
● Do not set the timer to more than 12 hours, as it
may result in spoiled rice.
7
Press the [Start/Rinse-free] key
once.
When cooking rinse-free rice,
press the key twice
The Timer function is set.
Minimum preset time
1 h
Plain rice
1 h 15 min
1 h
Beep-beep
Cooking time + 1 min
1 h 30 min
Grains other than
4 h 35 min
plain rice
Long
Beep
On
When cooking rinse-free rice
("Eco", "Plain", "Sushi", and
"Porridge" only)
Plain rice
Beep-beep
Beep
Grains other
than plain rice
Long
Beep
Blinks
• If you make a mistake or otherwise want to
reset the timer, press the [Cancel] key and
repeat the procedure from step
Display
Display
Beep
2
on P.20 .
21 21