DSC LE4000 Installation Manual page 26

Regulatory Information
MODIFICATION STATEMENT
Digital Security Controls has not approved any changes or modifications to this device by the user. Any
changes or modifications could void the user's authority to operate the equipment.
Digital Security Controls n'approuve aucune modification apportée à l'appareil par l'utilisateur, quelle qu'en
soit la nature. Tout changement ou modification peuvent annuler le droit d'utilisation de l'appareil par l'util-
isateur.
INTERFERENCE STATEMENT
This device complies with Part 15 of the FCC Rules and ISED Canada licence-exempt RSS standard(s). Oper-
ation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'ISED Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouil-
lage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
WIRELESS NOTICE
This equipment complies with FCC and ISED Canada radiation exposure limits set forth for an uncontrolled
environment. The antenna should be installed and operated with minimum distance of 20 cm between the radi-
ator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
Cet appareil est conforme aux limites d'exposition aux rayonnements de la ISED Canada pour un environ-
nement non contrôlé. L'antenne doit être installé de façon à garder une distance minimale de 20 centimètres
entre la source de rayonnements et votre corps. L'émetteur ne doit pas être colocalisé ni fonctionner con-
jointement avec à autre antenne ou autre émetteur.
Antenna gain must be below/Gain de l'antenne doit être ci-dessous:
Frequency Band/Bande de fréquence
GSM 850 / FDD V
PCS1900 / FCC II
LTEB2
LTEB4
LTEB5/ B12/ B13
FCC CLASS B DIGITAL DEVICE NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter-
ference in a residential installation. This equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio com-
munications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turn-
ing the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC ID:F5317LE4000
LE4000 Product Identifier US: F5317MO00ALE4000
REN: 0.0A
USOC Jack: RJ-31X
WARNING: To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation dis-
tance of 20cm or more must be maintained between the antenna of this device and persons during device
operation.
Telephone Connection Requirements
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply
with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord
and modular plug is provided with this product. It is designed to be connected to a compatible modular jack
that is also compliant. See installation instructions for details.
Ringer Equivalence Number (REN)
The REN is used to determine the number of devices that may be connected to a telephone line. Excessive
RENs on a telephone line may result in the devices not ringing in response to an incoming call.
In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of
devices that may be connected to a line, as determined by the total RENs, contact the local Telephone Com-
pany. For products approved after July 23, 2001, the REN for this product is part of the product identifier that
has the format. US: AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point
(e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.
Incidence of Harm
If this equipment LE4000 causes harm to the telephone network, the telephone company will notify you in
advance that temporary discontinuance of service may be required. But if advance notice is not practical, the
Telephone Company will notify the customer as soon as possible. Also, you will be advised of your right to file
a complaint with the FCC if you believe it is necessary.
Changes in Telephone Company Equipment or Facilities
The Telephone Company may make changes in its facilities, equipment, operations or procedures that could
affect the operation of the equipment. If this happens the Telephone Company will provide advance notice in
order for you to make necessary modifications to maintain uninterrupted service.
Equipment Maintenance Facility
If trouble is experienced with this equipment for repair or warranty information, please contact the facility
indicated below. If the equipment is causing harm to the telephone network, the Telephone Company may
request that you disconnect the equipment until the problem is solved. This equipment is of a type that is not
intended to be repaired by the end user.
DSC c/o APL Logistics, 757 Douglas Hill Rd., Lithia Springs, GA 30122
Additional Information
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public ser-
vice commission or corporation commission for information. Alarm dialling equipment must be able to seize
the telephone line and place a call in an emergency situation. It must be able to do this even if other equipment
(telephone, answering system, computer modem, etc.) already has the telephone line in use. To do so, alarm
dialling equipment must be connected to a properly installed RJ-31X jack that is electrically in series with and
ahead of all other equipment attached to the same telephone line. Proper installation is depicted in the figure
below. If you have any questions concerning these instructions, you should consult your telephone company or
a qualified installer about installing the RJ-31X jack and alarm dialling equipment for you.
Industry Canada Compliance Statement
This Equipment meets the applicable Industrial, Scientific and Economic Development (ISED) Canada Ter-
minal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation, IC,
before the registration number signifies that registration was performed based on a Declaration of Conformity
indicating that ISED Canada technical specifications were met. It does not imply that that ISED Canada
approved the equipment. The Ringer Equivalence Number (REN) for this terminal equipment is 0.0. The REN
assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be
LE4000
connected to a telephone interface. The termination on an interface may consist of any combination of
devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all devices does
4.20 dBi
not exceed 5.
7.30 dBi
IC:160A-LE4000
Cet équipement est conforme aux spécifications techniques applicables aux équipements terminaux d'ISED
8.00 dBi
Canada. Ceci est confirmé par le numéro d'enregistrement. L'abréviation IC précédant le numéro d'en-
8.80 dBi
registrement signifie que l'enregistrement a été effectué sur la base de la Déclaration de conformité indiquant
que le produit est conforme aux spécifications techniques d'ISED Canada. Ceci n'implique pas que le produit
5.40 dBi
ait été approuvé par ISED Canada.
Le nombre équivalent de sonneries (REN) de cet appareil terminal est 0.0. Le REN attribué à chaque équipe-
ment terminal fournit une indication sur le nombre maximum de terminaux pouvant être connectés sur une
interface téléphonique. La terminaison sur une interface peut constituer en n'importe quelle combinaison d'ap-
pareils, à la condition seulement que la somme des Nombres équivalents de sonneries de tous les appareils ne
soit pas supérieure à 5.
CAN ICES-3 (B) / NMB-3 (B)
The term "IC:" before the radio certification number only signifies that ISED Canada technical specifications
were met.
NIST Validation of encryption algorithm AES128 (certificate No. 5011 available at NIST website).