Airstream Caravanner 1977 Owner's Manual page 71

Table of Contents

Advertisement

lid carefully. When disposable filters are not
used, tap the two halves to release any dirt
trapped on the filters. The dust bubble can
also be rinsed out after removing both
upper and lower filters.
To remove the filters,
remove the lid and
grasp the large outer red ring in the upper
half of the bubble. Pull it gently toward you
until free. Lift out the small inner red ring
from the center of the bubble. Remove the
iid filter ring by pulling gently. To reposition
the filters reverse this procedure. When
properly positioned, the large outer red ring
should rotate freely on the flange.
Bed-lights
are operated by a switch on the
side of the light. To replace bulbs snap the
lens out by squeezing gently the long side
of the lens until it drops out of the fixture.
Area lights have switches on the rim and
their lenses are removed in the same
manner.
Ceiling light fixtures
are incorporated with
the ceiling fresh air vents. To operate the
lights turn the forward control knob clock¬
wise; first position 2 lights, second position
4 lights, third position 6 lights, fourth posi¬
tion is off.
To remove the lens and replace the bulbs,
puli knob from light switch shaft and re¬
move shaft nut. Remove the screw from
the vent control handle and remove handle.
This will release the lens. To replace,
reverse removal procedure.
The
fresh air vents
are operated by the aft
control handle. Turning clockwise will raise
the vent and at the maximum extension,
vents with fans will automatically turn on.
For maximum air without fan, open until fan
starts and back up just enough to turn fan
off. Turning counterclockwise will close the
vent. Airstream vents are designed to allow
air circulation while still keeping out rain
and can be used in any weather. Screens
should be removed for periodic cleaning.
The optional
NuTone Food Center
allows
you to operate several appliances with just
one built-in power unit. The food center is
equipped with three attachments, mixer,
blender, and knife sharpener. Other
appliance attachments are available.
Your power unit was oiled at the time of
manufacture but a storage period may
have permitted oil to drain back into the
reservoir. Before using it for the first time,
please run the power unit for one to two
minutes to insure lubrication...before
attaching an appliance. At intervals of from
one to two months, depending on the
amount of use, a few drops of ordinary
household oil should be placed around the
motor shaft opening.
The unit will warm up in proportion to the
length of time it's run and the load it carries.
If you run it unusually long or hard, give it a
rest before putting it to work again.
The
mixer
was designed for convenience
and efficient operation. The bowl rests on a
turntable directly connected to power unit.
The motor, not the beater, turns the bowl —
automatically keeps it revolving during
mixing, regardless of the consistency of the
batter. This feature eliminates hand-turning
the bowl. And, while the bowl revolves
automatically, the beater turns in the
opposite direction. This 'counter-motion'
feature helps prevent lumpy, incomplete
mixing.
To operate the mixer:
1. Place turntable in position on the power
unit.
2. Lock the turntable in place by pressing
the locking lever clockwise,
3. Place the mixing bowl on the turntable.
4. Push the beater blade into the beater
head. Blade will 'click' when it's locked in
position.
5. Insert beater head shaft into center tube
of bowl. Place it in one of six positions
until it snaps into turntable.
6. Turn dial to desired speed.
Note: To remove beater head, turn coun¬
terclockwise, and lift it out of mixing
bowl. If the turntable should become
locked into power unit and cannot be
easily removed, insert beater head and
turn it counterclockwise.
The
blender
makes meal preparation and
entertaining less work and more fun. It
performs, quickly and easily the time-
consuming and tiring tasks of grating,
chopping, shredding and mincing; it even
liquifies solids and blends them to
perfection.
To operate the blender:
1. Place blender in position on power unit,
61

Advertisement

Table of Contents
loading

Table of Contents