Table of Contents
Advertisement
ULXD
ULX-D Digital Wireless Microphone System
•
Other wireless systems or devices
•
Computers
•
CD players
•
Large LED panels
•
Effects processors
1. Press the SEL button to select a receiver channel.
2. Perform a group scan on the receiver: SCAN>GROUP SCAN.
3. Press SCAN to start the scan. SCANNING appears on the LCD during
the scan.
4. After the scan completes, the receiver displays the group with the most
available frequencies. Press the flashing ENTER button to deploy fre-
quencies to each receiver channel.
5. Power on the ULXD transmitter.
6. Press the sync button on the receiver.
7. Align the IR windows until the receiver IR port illuminates red.
Note: When complete, SYNC SUCCESS! appears. The transmitter and re-
ceiver are now tuned to the same frequency.
ULXD4
Digital Wireless Receiver
sync
1
EXIT
SCAN
3
SCAN COMPLETE
G:01 CH:21
485.775 MHz
Rssi: -118 dBm
5
sync
Multiple System Setup
A setup using networked receivers is the fastest and easiest way to distribute
the best open channel to each system. See Networking ULX-D Receivers
for networking details.
Note: Networked receivers must all be within the same frequency band.
2017/10/04
EXIT
control
RF
audio
gain
power
AB
OL
OL
ENTER
SCAN
EXIT
SCAN
push
2
EXIT
SCAN
4
ULXD2
on
6
Networked Receivers
1. Turn on all receivers.
2. Conduct a group scan on the first receiver to find available frequencies
in each group: SCAN>GROUP SCAN.
3. Press ENTER to accept the group number and automatically assign the
next best channel to each receiver on the network. The receiver LEDs
will flash when a frequency has been assigned.
4. Turn on a transmitter and sync to the receiver.
Important! Leave the transmitter on and repeat this step for each addi-
tional system.
Non-networked Receivers
1. Turn on all receivers.
2. Conduct a group scan on the first receiver to find available frequencies
in each group: SCAN>SCAN>GROUP SCAN>SCAN
3. When the scan is complete, use the control wheel to scroll through each
group. Press ENTER to select a group that has enough available frequen-
cies for all channels in the system.
4. Sync a transmitter to each receiver channel.
Important! Leave all transmitters on use the following steps to set up addi-
tional receiver channels:
1. Set each additional receiver channel to the same group as the first receiv-
er: RADIO>G:
2. Conduct a channel scan to find available frequencies within the group:
SCAN>SCAN>CHANNEL SCAN>SCAN
3. When the scan is complete, press ENTER to assign frequencies to each
receiver channel.
4. Sync a transmitter to each receiver channel.
Manual Frequency Selection
To manually adjust group, channel or frequency:
1. Select RADIO from the receiver menu.
2. Use the control wheel to select and adjust the group, channel, or frequen-
cy.
3. Press ENTER to save.
Transmitter IR Presets
Use the IR PRESETS receiver menu to quickly configure transmitter settings
from the receiver screen. When a sync is performed between the receiver
and transmitter, the IR PRESETs automatically configure the transmitter.
Each parameter has the default value KEEP, which leaves that setting unaf-
fected by a sync.
Feature
BP PAD
LOCK
10mW=Nm (normal), 1mW=Lo (low), 20mW=Hi
RF POWER
BATT
BP OFFSET
HH OFFSET
MUTE MODE
Cust. Group
Note: When Cust. Groups is set to on, it may take up to 30 seconds to
complete an IR sync.
Shure Incorporated
Setting
+0 dB, -12 dB
Power, Menu, All, None
(high)
Alkaline, NiMH, Lithium
0 dB to +21 dB (in 3 dB increments)
0 dB to +21 dB (in 3 dB increments)
OFF, ON
OFF, ON
17/29
Advertisement
Table of Contents
