Table of Contents
Advertisement
Master Programming Level
The Lock Enable option allows the programmer to select whether or not any installed ANN-80 or ANN-100 annunciator must be
unlocked by its key before any annunciator key presses will function. Pressing 2 while viewing the ANN-80/100 Options Screen #1
causes the display to toggle between Lock Enable Yes (annunciator must be unlocked for keys to function) and Lock Enable No (lock
position is ignored). This option is not available in Canadian applications. Refer to the table on page 49 for permissible settings.
The Acknowledge Button Enable (ACK BTN ENABLE) option allows the programmer to select whether the Ack/Step button on any
installed ANN-80 or ANN-100 annunciator will function normally or always be ignored. Pressing 3 while viewing the ANN-80/100
Options Screen #1 causes the display to toggle between Ack Btn Enable Yes (Ack/Step button functions normally) and Ack Btn Enable
No (Ack/Step button never functions). In Canadian mode, the FACP cannot be controlled by the ANN-100 so the Reset feature is
unavailable. This option is called STEP ENABLE in Canadian applications. Enabling the Step feature will allow the user to scroll
through events on the screen.
The Silence Button Enable (SIL BTN ENABLE) option allows the programmer to select whether the Silence button on any installed
ANN-80 or ANN-100 annunciator will function normally or always be ignored. Pressing 1 while viewing the ANN-80/100 Options
Screen #2 causes the display to toggle between Sil Btn Enable Yes (Silence button functions normally) and Sil Btn Enable No (Silence
button never functions).
The Reset Button Enable (RST BTN ENABLE) option allows the programmer to select whether the Reset button on any installed ANN-
80 or ANN-100 annunciator will function normally or always be ignored. Pressing 2 while viewing the ANN-80/100 Options Screen #2
causes the display to toggle between Rst Btn Enable Yes (Reset button functions normally) and Rst Btn Enable No (Reset button never
functions). In Canadian mode, the Reset feature is unavailable. The programming option will change to LMP BTN ENABLE in Canadian
applications. Pressing 2 while viewing the ANN-80/100 Options Screen #2 causes the display to toggle between Lmp Btn Enable Yes
(the ANN-100 will perform a local test of all LEDs) and Lmp Btn Enable No.
The Drill Button Enable (DRL BTN ENABLE) option allows the programmer to select whether the Drill button on any installed ANN-80
or ANN-100 annunciator will function normally or always be ignored. Pressing 3 while viewing the ANN-80/100 Options Screen #2
causes the display to toggle between Drl Btn Enable Yes (Drill button functions normally) and Drl Btn Enable No (Drill button never
functions). In Canadian mode, the Drill feature is unavailable. The programming option will change to SND BTN ENABLE in Canadian
applications. Pressing 3 while viewing the ANN-80/100 Options Screen #2 causes the display to toggle between Snd Btn Enable Yes (the
ANN-100 will perform a test of its local sounder by turning it on for 5 seconds) and Snd Btn Enable No.
3.6.9 Password Change
PROGRAMMING
1=PASSWORD CHANGE
2=CLEAR PROGRAM
3=PROGRAM CHECK
Programming Screen #4
Press 1 to change the Master Programming Level password, 2 to change the Maintenance Level password or 3 to change the Remote
Download password. Note that the passwords will not be displayed on LCD annunciators.
The following screen will appear when any change option is selected:
A flashing cursor will appear in the center of the display. Enter a new eight digit password (such as 10101010 for the Master Level).
After the eighth digit is entered, the following screen will be displayed:
Re-enter the new password to accept the change. The display will return to the initial Password Change Screen.
Invalid Password
If a password is entered incorrectly, the panel will display Invalid Message and a code.
ES-200X Series Manual — P/N LS10131-000FL-E:C 7/25/2018
The factory set passwords, which have been programmed into the control panel, can be changed by select-
ing the Password Change option. Pressing 1 while viewing Programming Screen #4 will cause the follow-
ing screen to be displayed:
PASSWORD CHANGE
1=MASTER
2=MAINTENANCE
3=REMOTE DOWNLOAD
Password Change Screen
ENTER NEW EIGHT DIGIT
PASSWORD
Enter Password Screen
VERIFY NEW PASSWORD
Password Change Screen
INVALID PASSWORD
Invalid Password Screen
Programming
99
Advertisement
Table of Contents
