1. Manuals
  2. Brands
  3. Heartland Manuals
  4. Test Equipment
  5. DT10
  6. Hardware manual

Heartland DT10 Hardware Manual

Dynamic test
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Ver.1.21
Hardware Manual
361 Fukui-cho, Ashikaga city, Tochigi prefecture 326-0338 Japan
Tel:+81-284-22-8791 / Fax:+81-284-22-8792
heartlanddata.com
URL:

Advertisement

Table of Contents
loading

Summary of Contents for Heartland DT10

  • Page 1 Ver.1.21 Hardware Manual 361 Fukui-cho, Ashikaga city, Tochigi prefecture 326-0338 Japan Tel:+81-284-22-8791 / Fax:+81-284-22-8792 heartlanddata.com URL:...
  • Page 2 DT10 Hardware Manual About this manual This manual explains the hardware specification and how to operate the DT10. ・ This program and manual are protected by Copyright Law, and no reproduction, reprinting or modification ・ whatsoever is permitted. The content and specification of this product are subject to change without prior notice.
  • Page 3 ・ A humid/dusty place ・ A wet place ・ A place exposed to direct sunlight ・ A place subject to considerable fluctuations in temperature and humidity ・ A place near HVAC equipment. Copyright © 2012 -2014 Heartland. Data Inc.
  • Page 4 Connect DynamicTracer to a PC by a cable connector ensuring the cable is in the correct Caution direction. When moving DynamicTracer, switch the power off, unplug the AC cable for safety and ensure all cables/connectors are disconnected. Copyright © 2012 -2014 Heartland. Data Inc.

  • Page 5: Table Of Contents

    Timing chart ....................- 15 - 4.5. GPIO CONNECTION ........................- 15 - 4.5.1. Timing chart ....................- 15 - 4.5.2. GPIO connection spec....................- 16 - 4.5.3. Level Shifter switch spec. Copyright © 2012 -2014 Heartland. Data Inc.
  • Page 6 HARDWARE SPEC. OF CAN CONNECTION ................- 23 - ........................... - 23 - 6.1. PPEARANCE ......................- 23 - 6.2. OMMUNICATION SPEC ........................- 23 - 6.3. OW TO CONNECT CHANGE HISTORY ......................... - 24 - Copyright © 2012 -2014 Heartland. Data Inc.

  • Page 7: Hardware Spec. Of Dynamictracer

    Connect Box / Analog Box connector 1.3. Connection image Use the attached USB cable to connect DynamicTracer to the PC being used. The PC’s USB port must support USB2.0. USB2.0 DynamicTracer - 1 - Copyright © 2012-2014 Heartland. Data Inc.

  • Page 8: Hardware Spec. Of Connect Box A

    Recommended operating condition (Connect Box A) Name Description UNIT High-level input voltage 2.37 Low-level input voltage 0.99 Input voltage Input resistance KΩ VIH/VIL/VI/RIN is the spec. of the probe and FPC cable. ・ - 2 - Copyright © 2012-2014 Heartland. Data Inc.

  • Page 9: Async Bus Connection

    H_WE/H_RE period H_WE/H_RE high-level period Data/Address setup time H_CE hold time Data/Address latch timing Waiting time from other CE access to H_CE active Waiting time from H_CE high-edge to CE access - 3 - Copyright © 2012-2014 Heartland. Data Inc.

  • Page 10: Fpc Cable Connection Spec

    本体側になるようにアタッ てお選びください。 チメントを取りつけます。 Here, 1 pin is shown. 　TSOP-48 PIN types are available - please use according to 　TSOP-56 PIN Intel系 　TSOP-56 PIN AMD系 the target: TSOP-48PIN TSOP-56PIN Intel TSOP-56PIN AMD - 4 - Copyright © 2012-2014 Heartland. Data Inc.

  • Page 11: Gpio Connection 4Bit / 2Bit

    24bit are treated as “0”. CS must be set “high”, except when outputting the Test Point. Never set it to “low” when the Test Point output stops. Caution - 5 - Copyright © 2012-2014 Heartland. Data Inc.

  • Page 12: Gpio Connection Spec

    　同時に挿入しないで下さい。 ▼ ▼ ▼ FPC cable at the same time. プローブのコネクタ Probe’s connector プローブの１ピン（黒の配線）が、 The probe’s 1PIN (black cable) Cコネクタの▼の位置側に なる様に挿入。 and the mark of the C-connector are matched and inserted. - 6 - Copyright © 2012-2014 Heartland. Data Inc.
  • Page 13 DT10 Hardware Manual Front view of the pin header - 7 - Copyright © 2012-2014 Heartland. Data Inc.

  • Page 14: Spi Connection

    * The number of “addr” bit varies (0/4/8/12/16/20/24) and high-order bits less than 24bit are treated as “0”. CS must be set “high”, except when outputting the Test Point. Never set it to “low” when the Test Point output stops. Caution - 8 - Copyright © 2012-2014 Heartland. Data Inc.

  • Page 15: Spi Connection Spec

    　同時に挿入しないで下さい。 ▼ ▼ FPC cable at the same time. ▼ プローブのコネクタ Probe’s connector プローブの１ピン（黒の配線）が、 The probe’s 1PIN (black cable) Cコネクタの▼の位置側に なる様に挿入。 and the mark of the C-connector are matched and inserted. - 9 - Copyright © 2012-2014 Heartland. Data Inc.
  • Page 16 DT10 Hardware Manual Front view of the pin header - 10 - Copyright © 2012-2014 Heartland. Data Inc.

  • Page 17: Hardware Spec. Of Connect Box B

    Ethernet ・ 10BaseT/100BaseTX ・ Supports auto-negotiation (Full-duplex/half duplex) ・ Supports auto MDI/MDIX (Crossover) ・ IP packet division is NOT supported UART ・ RS-232C-compliant ・ Supported baud rate 2400 - 921600 bps - 11 - Copyright © 2012-2014 Heartland. Data Inc.

  • Page 18: Hardware Spec. Of Connect Box C

    <Connect Box C 8pin probe> Name Description MIN. TYP. MAX. UNIT High-level input voltage (Level Shifter OFF) 2.36 High-level input voltage (Level Shifter ON) 1.17 Low-level input voltage 0.99 Input voltage Input resistance KΩ - 12 - Copyright © 2012-2014 Heartland. Data Inc.
  • Page 19 MAX. UNIT High-level input voltage 2.36 Low-level input voltage 0.99 Input voltage Input resistance KΩ Never connect anything except the relay box to the HDMI connector of Connect Box C. Caution - 13 - Copyright © 2012-2014 Heartland. Data Inc.

  • Page 20: Async Bus Connection

    H_WE/H_RE period H_WE/H_RE high-level period Data/Address setup time H_CE hold time Data/Address latch timing Waiting time from other CE access to H_CE active Waiting time from H_CE high-edge to CE access - 14 - Copyright © 2012-2014 Heartland. Data Inc.

  • Page 21: Gpio Connection 4Bit / 2Bit

    Connect to the DAT3 output pin Unused How to insert the probe. Connect Box C The black line of the 8pin probe is the 1st pin. The black line must be uppermost when connecting the probe. - 15 - Copyright © 2012-2014 Heartland. Data Inc.

  • Page 22: Level Shifter Switch Spec

    4.5.3. Level Shifter switch spec. When connecting to a target with output of 1.5V, the Level Shifter switch must be switched ON. In CLK, CS and Dat0 - Dat3 terminal, Level Shift is enabled. - 16 - Copyright © 2012-2014 Heartland. Data Inc.

  • Page 23: Spi Connection

    DAT3 Unused How to insert the probe Connect Box C The black line of the 8pin probe is the 1st pin. The black line must be uppermost when connecting the probe. - 17 - Copyright © 2012-2014 Heartland. Data Inc.

  • Page 24: Level Shifter Switch Spec

    4.6.3. Level Shifter switch spec. When connecting to a target with output of 1.5V, the Level Shifter switch must be switched ON. In CLK, CS and Dat0 - Dat3 terminal, Level Shift is enabled. - 18 - Copyright © 2012-2014 Heartland. Data Inc.

  • Page 25: Sd I/Fconnection

    SD card slot micro SD FPC micro SD card SD card or Connect Box C adapter for micro SD 4.7.2. Timing chart SD I/F bus timing Description MIN. MAX. UNIT CLK period - 19 - Copyright © 2012-2014 Heartland. Data Inc.

  • Page 26: Hardware Spec. Of Analog Box

    GND terminal for analog input Analog input terminal Logic input terminal BNC cable connection terminal Selector switch for analog input range 5.2. How to connect Connect between DynamicTracer and Connect Box. - 20 - Copyright © 2012-2014 Heartland. Data Inc.

  • Page 27: Logic Signal Input Spec

    Input for the D3 signal Input for the D4 signal Spec. of logic input Name MIN. TYP. MAX. UNIT Input voltage (can be specified from 0 to 5V by application) Sampling frequency Maximum input voltage - 21 - Copyright © 2012-2014 Heartland. Data Inc.

  • Page 28: Analog Signal Input Spec

    Input for the A2 signal A2 (BNC connector) Input for the A2 signal Spec. of analog input Name MIN. TYP. MAX. UNIT Resolution of the analog signal Sampling frequency Maximum input voltage - 22 - Copyright © 2012-2014 Heartland. Data Inc.

  • Page 29: Hardware Spec. Of Can Connection

    ・ Connect CANUSB and target board by D-SUB 9pin Connector. Download the CANUSB Direct Driver (D2XX) from LAEICEL’s website at http://www.canusb.com/ and install it. Caution Ensure your PC recognizes CANUSB before starting to use DT10. - 23 - Copyright © 2012-2014 Heartland. Data Inc.

  • Page 30: Change History

    ･ Description of GPIO 2bit is added to the spec. of ConnectBoxA and ConnectBoxC. ･The Pin used GPIO connection of ConnectBoxA. December 02, 2014 Ver.1.21 ･Front view of the pin header is added to the connection spec. of ConnectBoxA and ConnectBoxC. - 24 - Copyright © 2012-2014 Heartland. Data Inc.
  • Page 31 DT10 Hardware Manual 361 Fukui-cho, Ashikaga city, Tochigi prefecture 326-0338 Japan Tel:+81-284-22-8791 / Fax:+81-284-22-8792 heartlanddata.com URL: - 25 - Copyright © 2012-2014 Heartland. Data Inc.

Table of Contents