Advertisement
2
Fixing
screw
M3 x 4
(included)
4
6
8
9
11
Safety wire
Secure to an
LAN cable
anchor or
structure
Backside
ceiling
Ceiling
bracket
bracket
Dome
Ceiling board
Camera
External Dimensions
162 (6.38)
(Max. circumscribed
exterior dimension)
204 (8.03)
3
Fixing
screw
M3 x 3
(included)
5
Ceiling bracket screw
M4 x 3
(included)
7
10
7( 0.28)
Unit: mm (in.)
Installing the Camera
The procedures for mounting the camera to the ceiling using the indoor dome housing are
described below.
Before installing the camera, set the IP address and other network information on the camera
using the "VB Initial Setting Tool" on the Setup CD-ROM.
For details on how to operate the "VB Initial Setting Tool", see "Operation Guide".
If using an memory card, insert the memory card into the camera before installing (see
"Installation Guide" > "Using an Memory Card" included with the camera).
Important
Once the camera is installed to the ceiling, to insert and remove the memory card, the camera must be
removed from the ceiling and the ceiling bracket dismounted.
1
Determine an installation position for the camera and drill holes in the ceiling
Using the included template, line up the directon of the camera, determine the locations of
the backside ceiling bracket mounting holes (three) and the ceiling bracket holes, then drill
the holes ( 165 mm ( 6.50 in.)) into the ceiling.
Use the template with the printed side facing you.
Important
When mounting the indoor dome housing, be sure no shavings enter the dome.
2
Mount the camera to the ceiling bracket
Affix with four included fixing screw (M3).
3
Mount the dust cover to the ceiling bracket
Affix with three included fixing screw (M3).
4
Attach the backside ceiling brackets inside the ceiling
From the inside of the ceiling, insert the protrusions on the backside ceiling brackets through
the mounting holes drilled in step 1.
5
Temporarily tighten screws to the backside ceiling bracket
Temporarily tighten the three included ceiling bracket screws (M4) through the ceiling.
6
Secure the safety wire
Securely attach the safety wire to an anchor or structure. After securing one end of the safety wire
to the ceiling, secure the other end to the camera using the screw that is fastened to the camera.
7
Connect the LAN cable to the camera through the wiring hole
If AC Adapter (sold separately) or an external power supply is used, connect the power connector
to the camera. Connect cables to external device I/O terminals and audio input/output terminals
as necessary (see "Installation Guide" > "Connecting the Camera" included with the camera.).
8
Mount the ceiling bracket on the ceiling
Position the ceiling bracket over the screws temporarily tightened in step 5, turn clockwise to
temporarily secure in place, and completely fasten the screws.
9
Attach the dome
Align the (O) mark on the dome with the (I) mark on the ceiling bracket, and turn clockwise
until the (I) mark on the dome aligns with the (I) mark on the ceiling bracket. This procedure
also aligns the ceiling bracket screw hole with the dome fixing screw hole.
10
Affix the dome
To prevent the dome from rotating, attach one dome fixing screw (M2).
11
Reboot the camera when the installation is complete
The camera position is initialized (see "Operation Guide" > "Setting Page" > "Maintenance").
Note
While the LED is on, light may reflect inside the dome and be captured on video. If this happens, set the
LED setting to [Turn Off] (see "Operation Guide" > "LED Setting").
Main Specifications
Model
DR41-C-VB/DR41-S-VB
Type
Clear/Smoked
Dimensions
( x H) 204 x 176 mm ( 8.03 x 6.93 in.) (Dome: R62 mm (R2.44 in.))
Weight
Approx. 765 g (1.687 lb.) (excluding camera)
Smoked (DR41-S-VB)
This dome is approximately 50% transparent.
Min. subject illumination
Day Mode (color)
0.8 lux (F1.6, shutter speed 1/30 sec., when smart shade control is off, 50IRE)
0.06 lux (F1.6, shutter speed 1/2 sec., when smart shade control is off, 50IRE)
0.02 lux (F1.6, shutter speed 1/2 sec., when smart shade control is on, 50IRE)
0.8 lux (F1.6, shutter speed 1/30 sec., when smart shade control is off)
0.2 lux (F1.6, shutter speed 1/8 sec., when smart shade control is off)
0.06 lux (F1.6, shutter speed 1/8 sec., when smart shade control is on)
Night Mode (monochrome)
0.04 lux (F1.6, shutter speed 1/30 sec., when smart shade control is off, 50IRE)
0.004 lux (F1.6, shutter speed 1/2 sec., when smart shade control is off, 50IRE)
0.002 lux (F1.6, shutter speed 1/2 sec., when smart shade control is on, 50IRE)
0.02 lux (F1.6, shutter speed 1/30 sec., when smart shade control is off)
0.004 lux (F1.6, shutter speed 1/8 sec., when smart shade control is off)
0.002 lux (F1.6, shutter speed 1/8 sec., when smart shade control is on)
Advertisement
