Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
VP101-BT Installation Guide
• 1 VP101-BT system unit
• 6 Mounting screws for Mini PCIe module
• 1 Quick Installation Guide
• 1 Disk includes:
- Drivers / Manual
Note:
The CD that came with the system contains an autorun screen to install drivers, utilities,
and software applications required to enhance the performance of the system and a user's
manual for your reference. Insert the CD into a CD-ROM drive. The autorun screen will ap-
pear. If after inserting the CD, "Autorun" did not automatically start, please go directly to
the root directory of the CD and double-click "Setup". Please install all required drivers.
DFI reserves the right to change the specifications at any time prior to the product's release. For the latest revision and details of the
installation process, please refer to the user's manual.
Package Contents
www.dfi.com
1
Advertisement
Table of Contents
Related Manuals for DFI VP101-BT
Summary of Contents for DFI VP101-BT
-
Page 1: Package Contents
CD and double-click “Setup”. Please install all required drivers. DFI reserves the right to change the specifications at any time prior to the product's release. For the latest revision and details of the installation process, please refer to the user's manual. - Page 2 Panel Antenna hole COM 4/ 8-bit DIO CANbus* COM 1/2 (RS232/RS422/RS485) Power button Top View USB 3.0 HDMI Reset switch/ Status LED VCC/ACC/GND (Connects to car battery) LAN 1 MIC-in LAN 2 Bottom View COM 5 USB 2.0 (RS232) Line-out COM 3 (RS232/RS422/RS485) Note:...
-
Page 3: Removing The Chassis Cover
Removing the Chassis Cover Please observe the following guidelines and follow the procedure to open the system. 1. Make sure the system and all other peripheral devices connected to it have been powered off. 2. Disconnect all power cords and cables. 3. -
Page 4: Installing A Mini Pcie Card
Installing a Mini PCIe Card The system board is equipped with 3 Mini PCIe slots: two full-size and one half- size slots. Here we will demonstrate the installation of a half-size Mini PCIe card (PCIe/USB/LPC signals) for WiFi connection. 1. Grasp the Mini PCIe card by its edges and align the notch in the connector of the card with the notch in the connector on the system board. -
Page 5: Installing A Sata Drive
Installing a SATA Drive The system can accomondate one SATA drive. Please use the following procedure to install a SATA drive into the system. 1. SATA HDD bay is located under the power board. Please remove the power board first to uninstall the HDD bracket. Power board Mounting screws SATA bracket... -
Page 6: Mounting Options
Mounting Options Wall mount The wall mount kit includes the following: • 2 wall mount brackets • Bracket screws Wall mount bracket 1 Wall mount bracket 2 1. Select a place on the wall where you will mount the system. 2. - Page 7 3. Attach the other bracket (wall mount bracket 2) to the rear of the system. Mounting screw Wall mount bracket 2 Mounting screw Hooks 4. Slide the system to "wall mount bracket 1" to attach the two brackets with the hooks.
-
Page 8: Panel Mount
3. Insert the system from the outside surface of the panel into the mount- ing hole until it is properly fitted against the panel. 4. Position the mounting clamps along the rear edges of the system and insert them into the slits around the system. www.dfi.com... - Page 9 5. The first and second clamps must be positioned and secured diagonally prior to mounting the rest of the clamps. Tighten the clamp’s screw using an electric screwdriver by pressing the white plastic cap onto the back of the panel. The illustration below shows that all clamps are properly mounted.
-
Page 10: Board Layout And Jumper Settings
1-2, 4-5 COM 4 (default) 7-8, 10-11 On GND (default) 1-2 On +5V or +5V_standby 2-3 On 2-3, 5-6 8-9, 11-12 On Note: You cannot use COM 4 and DIO at the same time. Please adjust JP21 and JP22 together. www.dfi.com... - Page 11 Delay Turn-on/off Switch The DIP switch (SW1) on the power board can be used to trun on or off the sys- tem at a specific on/off delay time via car ignition. SW1-2: System-on delay enable/disable On (Default) Enable (delay time setting adjust- able by SW1-4 and 1-5 as shown in the table below) Disable (System-on delay = 3 sec)