Roller Nip Settings; Using Foot Pedal And Remote Control - Royal Sovereign RSC Series Owner's Manual

7. SPEED AND TEMPERATURE SETTINGS
RSC-1650H/C/HR
Speed# Speed(Ft/min,M/min) T e m p . #
1 4(1.2) 1
2 6(1.7) 2
3 7(2.2) 3
4 9(2.6) 4
5 10(3.1) 5
6
6 12(3.6)
7 14(4.2) 7
8 15(4.5) 8
9
9 16(5.0)
8. ROLLER NIP SETTING
It is important to adjust the roller nip settings to the appropriate thickness of the board
being used. Use the guide below to adjust to the correct position.
Metric
NO. Inches
(mm)
1 Lamination Lamination
2 1/ 25" 1
3 3/16"~1/4" 5-7
4 3/ 8"~1/2" 10-13
5 3/5" 15
NOTE: If you don't want to
laminate,please place the
pressure lever to the "Open
position(NO.5)".
R S C - 1 6 5 0 H R S C - 1 6 5 0 H R
? ? ? ? ? ? ? ?
? ? ? ? ? ?
? ? ? ? ? ?
T e m p e r a t u r e ( W 2 6 X F , ? ? ? W 2 6 X ? ? ? C ) T e m p e r a t u r e ( W 2 6 X
? W & ( M I ' ) X ? ? 7 H e N 1 ? ? ? e ? ? ? ? ? ? W & ( M I ' ) X ? ? 7 H e N 1 ? ? ? e ? ? ? ? ? ? ? 7 H e N 1 ? ? W & ( M I ' ) X ? ? e ? ?
? V ' ) K O & ( Y ? ? 3 L e J 5 ? V 4 0 Y ? ? ? ? ? V ' ) K O & ( Y ? ? 3 L e J 5 ? V 4 0 Y ? ? ? ? V 4 ? V ' ) K O & ( Y ? ? 3 L e J 5 ? 0 Y
? ? ? ? ? ?
? ? ? ? ? ?
? ? ? ? ? ?
? ? ? ? ? ? ? ?
N o H e a t i n g N o H e a t i n g
N o H e a t i n g 8 6 ( 3 0 )
9 1 ( 3 3 ) 1 1 3 ( 4 5 )
9 7 ( 3 6 ) 1 4 0 ( 6 0 )
1 0 4 ( 4 0 ) 2 3 0 ( 1 1 0 )
1 1 1 ( 4 4 ) 2 3 9 ( 1 1 5 )
1 1 5 ( 4 6 ) 2 4 8 ( 1 2 0 )
1 1 7 ( 4 7 ) 2 5 7 ( 1 2 5 )
1 2 4 ( 5 1 ) 2 6 6 ( 1 3 0 )
7

9. USING FOOT PEDAL AND REMOTE CONTROL

USING FOOT PEDAL
? ? ? ? ? ? ? ? Place the foot pedal on the floor in front of the
? ? ? ? ? ?
? ? ? ? ? ?
? ? ? F , W 2 6 X C ) ? ? ?
? ? ? ? W & ( M I ' ) X ? ? ? 7 H e N 1 ? ? e ? ? ? ? ?
? ? ? ? ? 3 L e J 5 ? ? V ' ) K O & ( Y ? V 4 0 Y ? ? ? ?
? ? ? ? ? ?
? ? ? ? ? ?
? ? ? ? ? ?
? ? ? ? ? ? ? ?
machine. Once all correct settings are displayed, you
may use the foot pedal to operate the laminator for
"Hands Free Operation." To activate the machine,
press the foot pedal once and then release. Repeat
to stop the rollers.
USING REMOTE CONTROL
Located on the rear left side of the laminator.
1. PRESS RUN – To activate the rollers.
2. PRESS STOP – To stop the rollers from turning.
3. PRESS REV – To reverse the rollers. Press and
hold the button (useful for jams or misted media).
RSC Series
1 2 3
8