Error - Lenze 8400 motec Software Manual

8400 motec | Software Manual
Index
Motor magnetising inductance (C00092)
Motor overload threshold (I²xt) (C00120)
Motor parameter identification
Motor parameter identification is active
Motor selection
Motor stator leakage inductance (C00085)
Motor stator resistance (C00084)
Motor temperature monitoring (PTC)
Motor voltage (C00052)
N
Nact filter time constant (C00497)
Network MCI/AN output words (C00877)
Network MCI/CAN input words (C00876)
Number of encoder increments (C00420)
O
OC1
Power section - short circuit (error message)
OC12
I2xt overload - brake resistor (error message)
OC2
Power section - earth fault (error message)
OC5
Ixt overload (error message)
OC6
I2xt overload - motor (error message)
OC9
Ixt overload - shutdown limit (error message)
OH
Heatsink overtemperature (error message)
OH3
Motor temperature (X106) triggered (error
message) 210
OS1
Maximum speed limit reached (error message)
Oscillation damping
Oscillation damping influence (C00234)
OT2
Speed controller output limited (error message)
OU
DC bus overvoltage (error message)
Output frequency (C00058)
Output power (C00980)
P
Parameter change-over
Password (C00094)
Password1 (C304)
Password2 (C305)
Peak current limitation
Plant parameters
Port block "LP_Network_In"
Port block "LP_Network_Out"
Power and energy display
372
246
250
59
44
54
245
245
125
242
272
289
289
266
212
212
211
213
210
106
264
211
243
292
172
246
265
265
64
58
224
225
120
L
Power section identification (C00093)
Power-on time meter (C00179)
Product type code (C00203)
PROFIBUS 220
PROFINET 220
PS01
No memory module (error message)
PS02
Par. set invalid (error message)
PS03
Par. set device invalid (error message)
PS04
Par. set device incompatible (error message)
PS31
Ident. error (error message)
PTC 125
R
Ramp smoothing, main setpoint (C00134)
Rated motor current (C00088)
Rated motor frequency (C00089)
213
Rated motor power (C00081)
Rated motor speed (C00087)
Rated motor torque (C00097)
Rated motor voltage (C00090)
Rated power brake resistor (C00130)
Reaktion brake resistor control (C00175)
Reduc. brake chopper threshold (C00174)
211
Reset of error message
Resp. to communication error with MCI (C01501)
Resp. to control word error (C00594)
Resp. to DC bus undervoltage (C00600)
Resp. to device overload (Ixt) (C00604)
Resp. to encoder open circuit (C00586)
Resp. to heatsink temp. > cut-off temp. -5°C (C00582)
212
275
Resp. to lim. speed controller (C00567)
Resp. to LP1 motor phase fault (C00597)
Resp. to LS_SetError_x (C00581)
213
Resp. to mains phase failure (C00565)
Resp. to max. speed reached (C00607)
Resp. to motor overload (I²xt) (C00606)
Resp. to motor overtemp. PTC (C00585)
Resp. to open circuit AINx (C00598)
Resp. to overtemp. brake resistance (C00574)
Resp. to speed monitoring (C00579)
S
Safety instructions
Saving parameters automatically
SD10
Speed limit - feedback system 12 (error message)
213
Firmware ≤ 02.00 - DMS 2.1 EN - 03/2011
246
261
262
216
216
216
216
217
251
245
245
244
245
247
246
251
260
260
207
296
276
276
277
275
274
276
275
273
277
277
275
276
274
274
14
37