Display Informations; Alarm Signals - Kalor Denia 14 Installer And User Manual

Display informations

21:10
22°C P-1
21:10
OFF
22°C P-1
21:10
OFF
22°C P-1
14:35
OFF
21°C P-2
14:35
START
21°C P-2
14:35
START
21°C P-2
14:35
START
21°C P-2
14:35
LOAD
21°C P-2
14:35
pellet
LOAD
21°C P-2
pellet
14:35
LOAD
21°C P-2
pellet
14:35
FLAME
21°C P-2
LIGHT
14:35
FLAME
21°C P-2
(5)
LIGHT
15:18
FLAME
21°C P-3
(5)

Alarm signals

LIGHT
15:18
WORK
21°C P-3
(5)
15:18
WORK
In the event of a working defect, the system informs the user about the type of failure occurred.
21°C P-3
The following table summarises the alarms, kind of problem and possible solution:
16:40
WORK
22°C P-2
16:40
Upper Lower
CLEANING
22°C P-2
Display Display
16:40
FIRE-POT
CLEANING
22°C P-2
AL 5
FIRE-POT
CLEANING
FIRE-POT
NO
AL 6
PELLET
PROBE
AL 2
EXHAUST
SAFETY
AL 7
THERMAL
COOL FIRE
FAN
AL 4
FAILURE
FAILURE
AL 8
DEPRESS
SERVICE
Regular checks should be carried out by the user, who should only contact the Authorized Assistance Center
if no solution is found.
OFF
The stove is off.
START
The stove is switching on.
Resistance and smokes extractor
are on.
LOAD PELLET
The stove starts loading pellets in
the brazier.
Resistance, smokes extractor and
gear motor are on.
Kind of failure
The cannot start up
This is the first light-up
The pellet stove switched off while work-
ing
The smokes sensor is broken or not
connected to the pcb
The stove is overheated
There is no power supply
Smokes extractor blocked or broken
Obstructed flue
The stove has worked for 1300 hours.
Supplementary maintenance required
21°C P-2
14:35
START
21°C P-2
14:35
LOAD
21°C P-2
14:35
pellet
LOAD
21°C P-2
pellet FLAME LIGHT
14:35
LOAD
The stove starts loading pellets in
21°C P-2
14:35
pellet the brazier.
FLAME
Smokes extractor and gear mo-
21°C P-2
LIGHT 14:35
tor are on.
FLAME
21°C P-2
(5)
LIGHT
15:18
FLAME
(5)
WORK
21°C P-3
LIGHT
15:18
The stove is working, in this case
WORK
21°C P-3
(5)
with working power 3. Detected
15:18
WORK
room temperature is 21°C. Smokes
21°C P-3
ventilator, gear motor and room
16:40
WORK
ventilator are on during this phase.
22°C P-2
16:40
CLEANING
22°C P-2
CLEANING FIRE-POT
16:40
FIRE-POT
CLEANING
The stove is cleaning the brazier.
22°C P-2
FIRE-POT
The smokes extractor is working
CLEANING
at its max. speed and the pellets
FIRE-POT
loading is minimal.
Fill in the tank with pellets
Start up again
Fill in the tank with pellets
Contact an Authorized Assistance Center
Reset the thermostat manually. If the problem persists,
contact an Authorized Assistance Center.
As soon as the power supply is back, the stove starts a cool-
ing cycle. After completing the cycle it starts working auto-
matically
Contact an Authorized Assistance Center
Clean the flue or check there are no obstructed grids near the
smokes exhaust
Contact an Authorized Assistance Center
Solution
45