Remote Zone Connections; A Word About Watts; Operating The Rsx-1550; Front-Panel Display - Rotel RSX-1550 Owner's Manual

English English
FM Antenna
t
See Figure 12
The receiver is supplied with a T-shaped indoor FM antenna. Connect the
coax F-type plug to the FM antenna connector on the RSX-1550. For best
reception, unfold the T-shaped antenna. Eyelets at both ends of the T allow
tacking the antenna to a wall, if desired. Experiment with positioning for
best reception.
Note: To use an outdoor antenna, connect its 75 ohm coax lead
wire to the FM connector instead of the indoor wire antenna, only
after a professional contractor has installed the antenna system in
accordance with local electrical codes.

Remote Zone Connections

This Rotel receiver has connections for three independent remote zones.
For audio connections to a remote zone, connect the left and right
ZONE 2, 3, or 4 jacks to the left and right channels of a remote zone
amplifier with an RCA audio cable.
For video connections to a remote zone, connect the ZONE 2, 3,
or 4 VIDEO OUT jack to the input of a TV in the remote zone using a
composite video cable.
For control of the receiver from a remote zone: connect a remote
zone IR repeater to the ZONE 2, ZONE 3, or ZONE 4 REM IN jack
using a cable terminated with 3.5mm plugs.

A Word About Watts

This receiver's power output is quoted as 75 watts for each channel,
when all five channels are operating together at full power. Rotel
has chosen to specify the power output in this way because in Rotel's
experience it gives the truest value of the amplifier or receiver's power
capability.
When comparing specifications for different products, you should be
aware that power output is often specified in other ways, so you may not
be comparing like with like.
For example, the power output may be quoted with only two channels
operating, giving a higher maximum figure. If Rotel chose to quote the
RSX-1550's power output this way, for two channels only, the figure
would rise to 100 watts per channel, for the same distortion limit and
loudspeaker impedance.
RSX-1550 English v2.indd 25
i]\

OPERATING THE RSX-1550

Considering its large number of features, settings, and options, this Rotel
receiver is remarkably easy to operate. The key to operating the unit is
its system of On-Screen Displays (OSD) which guide you through various
choices.
The receiver can be operated from the front panel or the remote control.
Front-panel controls are unusually simple to use, with just a few knobs
and buttons to guide you through OSD menu options. The remote control
provides more complete control options.
To guide you through the operation of the unit, this section of the manual
starts with explaining the basic layout and function of the front panel and
the remote control. Then, we explain the basic operations such as turning
the unit on and off, adjusting volume, selecting a source for listening,
etc. Following that is a detailed explanation of surround sound modes
and how to configure the receiver for various types of recordings. Finally,
there are instructions for additional features and Zones operation. All of
these are features that may be used in normal use. The last section of the
manual (Configuration) details options that may be selected during initial
setup and configuration of the unit, many of which will be set once and
left untouched.
Throughout this manual, numbers in square boxes refer to the main unit
illustration at the front of this manual. Letters refer to the remote handset
illustration. When both appear, the function is found on both the unit's
front panel and on the remote. When only one appears, that function is
found either only on the main unit, or only on the remote.
Front Panel Overview
The following is a brief overview of the control and features on the front
panel of the receiver. Details concerning the use of these controls are
provided in subsequent sections of this manual describing various tasks.

Front-panel Display

5
The fluorescent (FL) display on the front panel provides information
useful for operating the unit. The main portion of the display has two
rows of alpha-numeric text displays. The top line shows the currently
selected source input on the left and the volume setting on the right. The
second line shows the current surround mode or other settings as they
are changed (record source selection, Zone 2 source selection, dynamic
range settings, etc.)
Icons along the left side of the display show the current surround mode.
Icons along the bottom left of the display show the current digital input.
Icons along the right bottom of the display show individual surround
channels when configuring the system.
The FL display can be turned off, if desired. See the MENU button section
for instructions.
25 25
27/8/08 14:22:13