Moxa Technologies ioLogik E1510-T Quick Installation Manual

ioLogik E1500 Series

Quick Installation Guide

Second Edition, February 2015
Overview
With a threaded M12 Ethernet port to ensure wired connectivity, a
spring-type terminal block for vibration-resistant cabling, and a
DIN rail mount assembly, the ioLogik E1500 series is designed to
withstand the severe vibrations experienced with rolling stock and
wayside applications. Carefully engineered channel-to-channel
isolation gives protection against cross-line power surges and
crosstalk, ensuring stable data communications. In addition, the
ioLogik E1500 is compliant with EN 50121-3-2, EN 50121-4, and
essential sections of the EN 50155 standard (covering operating
temperature, power input voltage, electrical surges, ESD, and
vibration), all of which are required for electronic equipment used
on or around railway vehicles.
Model Selection
ioLogik DI DO DIO Relay AI
E1510-T 12 – – – –
E1512-T 4 – 4 – –
Package Checklist
• 1 ioLogik E1500 series remote I/O product
• Documentation and software CD
• Quick installation guide (printed)
P/N: 1802015000011
– 1 –

Specifications

System
Ethernet
Protection
Protocols
Power Input
Wiring
Dimensions
Weight
Operating Temperature -40 to 85°C (-40 to 185°F)
Storage Temperature
Ambient Relative
Humidity
Altitude:
Note: Please contact Moxa if you require products guaranteed to
function properly at higher altitudes.
Standards and
Certifications
Warranty Period
Details
Digital Input
Sensor Type
I/O Mode
Dry Contact
AO RTD TC
– – –
Wet Contact
– – –
Isolation
Counter/Frequency
Digital Output
I/O Mode
Pulse Wave
Width/Frequency
Over-voltage
Protection
Over-current Protection 2.6 A (4 channels @ 650 mA)
Over-temperature
Shutdown
Current Rating
Isolation
10/100 Mbps, M12 connector
1.5 KV magnetic isolation
Modbus/TCP, TCP/IP, UDP, DHCP, Bootp,
HTTP
24 VDC nominal, 12 to 48 VDC
I/O cable, max. 14 AWG
144 x 124 x 30 mm (5.67 x 4.88 x 1.18 in)
825 g
-40 to 85°C (-40 to 185°F)
5 to 95% (non-condensing)
Up to 2000 m
UL 508, EN 50155, EN 50121-3-2, EN
50121-4
5 years
See www.moxa.com/warranty
NPN, PNP, and Dry contact
DI or Event Counter
• On: short to GND
• Off: open
• On: 0 to 3 VDC
• Off: 10 to 30 VDC
3k VDC or 2k Vrms
250 Hz, power off storage
DO or Pulse Output
1 ms/500 Hz
45 VDC
175°C (typical), 150°C (min.)
200 mA per channel
3k VDC or 2k Vrms
– 2 –
Installation
Power and Networking
Connect the +12 to +48 VDC power line to the ioLogik E1500's
terminal block V+ terminal, and connect the ground from the
power supply to the V- terminal. If an earth ground is available,
connect the ground pin ( ).
Mounting and Cabling
The ioLogik E1500 can be used with both DIN rail and wall mounts.
When mounting on a DIN rail, release the bottom mounting kit,
install the ioLogik on the rail, and then restore the bottom
mounting kit to fix the ioLogik to the rail. When using wall
mounting, release both the upper and bottom DIN rail kits.
The ioLogik E1500 has an M12 Ethernet port for connecting either
a standard direct-Ethernet or crossover-Ethernet cable via a
locking M12 connector.
LED Indicators
Type Color Description
PWR Green System power in ON
Off System power is OFF
RDY Green System is ready
Green Blinking Located
Red System Booting-up Error
Green/Red Safe Mode
Blinking
Red Blinking Firmware upgrade (LED flashes for 3
seconds then stays red until restart)
Off System is not ready
LAN Green 100 Mbps
Amber 10 Mbps
Blinking Data Transmitting
Off Ethernet Off
EXP Green Expansion Mode Ready
Red Configuration Failure
Off Stand-alone Mode
DI Green Channel ON
Off Channel OFF
DIO Green Channel ON
Off Channel OFF
– 3 –