Side-Power SXP80/185T Installation And User Manual

Side-Power SXP80/185T Installation And User Manual

External stern thruster assembly

Advertisement

Quick Links

SIDE-POWER
Thruster Systems
Installation and user manual
SLEIPNER MOTOR AS
P.O. Box 519
N-1612 Fredrikstad
Norway
Tel: +47 69 30 00 60
Fax: +47 69 30 00 70
SXP80/185T & SXP100/185T
External sternthruster
w w w . s i d e - p o w e r . c o m
s i d e p o w e r @ s l e i p n e r. n o
assembly
© Sleipner Motor AS version 2015

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SXP80/185T and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Side-Power SXP80/185T

  • Page 1 SXP80/185T & SXP100/185T External sternthruster SIDE-POWER assembly Thruster Systems Installation and user manual SLEIPNER MOTOR AS P.O. Box 519 N-1612 Fredrikstad Norway Tel: +47 69 30 00 60 w w w . s i d e - p o w e r . c o m Fax: +47 69 30 00 70 s i d e p o w e r @ s l e i p n e r.
  • Page 2: Table Of Contents

    This removes any possibility for solenoid lock in. Any fault in the main solenoids will give feed back to the panel and turn off power to the electric motor. Max. stern thickness: 100mm (80mm recommended) SXP80/185T & SXP100/185T External stern thruster assembly 1.0.2 - 2016...
  • Page 3: Planning & Important Precautions

     If you are installing the Sidepower in a small room /compartment, it should be ventilated to ensure cooling of the electromotor.  If the height in the room you are installing the Side-Power is limited, the Side-Power can be installed horizontally or at any angle in between.
  • Page 4: Bolt On Installation

    4. When fitting the thruster assembly, ensure that there is ample sealant (Sikaflex or similar) around the center tube with cable connectors and around the bolts to make a water tight fitting (Fig. 1/2). Bolts diameter: ø 12mm stainless steel SXP80/185T & SXP100/185T External stern thruster assembly 1.0.2 - 2016...
  • Page 5: Installation Measurements

    Installation measurements SXP80/185T & SXP100/185T External stern thruster assembly 1.0.2 - 2016...
  • Page 6: Electrical Installation

    • It is highly recommended to install a Side-Power Automatic Main Switch 897712 (12V) eller 897724 (24V). The AMS will be activated when the panel is turned on, contains an automatic short circuit fuse and a manual emergency stop. The AMS will also provide feedback to the panel regarding evt.
  • Page 7: Control Panel And Control-Leads

    IMPORTANT! Battery banks must have common negative SXP80/185T & SXP100/185T External stern thruster assembly 1.0.2 - 2016...
  • Page 8: Visual Wiring Diagram

    Technical wiring diagram, thruster motor SXP80/185T & SXP100/185T External stern thruster assembly 1.0.2 - 2016...
  • Page 9: Electrical Installation Of Stern Thruster Systems

    Battery cable size used: ..............The compartment where the thruster is fitted is isolated from general bilge water and has no obvious or suspected risks for flooding. Other comments by installer: SXP80/185T & SXP100/185T External stern thruster assembly 1.0.2 - 2016...
  • Page 10: Important User Precautions

     If there is a problem with your Ignition Protected stern thruster, please contact your dealer. Danger: NEVER Disassemble any part of the Ignition Protected stern thruster assembly  SXP80/185T & SXP100/185T External stern thruster assembly 1.0.2 - 2016...
  • Page 11: How To Use Side-Power Thrusters

    2. Please take some time to exercise thruster usage in open water to avoid damages to your boat. 3. Turn the control panel on by pushing both “ON” buttons on the original Side-Power panel simultaneously. 4. Move the joystick in the direction you wish the bow to move. Other controls like foot switches or toggle-switches on the throttle can be used.
  • Page 12: Maintenance

     If there is a problem with your Ignition Protected stern thruster, please contact your dealer. Danger: NEVER Disassemble any part of the Ignition Protected stern thruster assembly  SXP80/185T & SXP100/185T External stern thruster assembly 1.0.2 - 2016...
  • Page 13: Troubleshooting

    Trouble shooting Before seeking assistance at the help desk of your Side-Power dealer / distributor please perform these tests and make notes of all measurements to ensure that they have as much information as possible to work on. NB! All check points and solutions must be carried out after consulting the relevant information elsewhere in this manual to understand how the system is intended to work.
  • Page 14: Warranty Statement

    8. The Warrantor assumes no liability for incidental or consequential damages of any kind including damages arising from collision with other vessels or objects. 9. This warranty gives you specific legal rights, and you may also have other rights which vary from country to country. SXP80/185T & SXP100/185T External stern thruster assembly 1.0.2 - 2016...
  • Page 15: Checklist

    256 / 10.08 340 / 13.39 All measurements in mm / inches. Sleipner Motor AS • P.O.box 519 • 1612 Ph: (+47) 69 30 00 60 • Fax: (+47) 69 30 00 SXP80/185T & SXP100/185T External stern thruster assembly 1.0.2 - 2016...
  • Page 16: Service Centres

    SLEIPNER MOTOR AS P.O. Box 519 N-1612 Fredrikstad Norway Tel: +47 69 30 00 60 Fax:+47 69 30 00 70 www.side-power.com sidepower@sleipner.no The information given in the document was correct at the time it was published. However, Sleipner Motor AS can not accept liability for any inaccuracies or omissions it may contain.

This manual is also suitable for:

Sxp100/185t

Table of Contents