Auto Pan - Roland SH-32 Owner's Manual

AUTO PAN

Cyclically modulates the stereo location of the sound.
fig.AutoPan
L in
Auto Pan
R in
Auto Pan
Parameter Value
INTENSITY 0.05–10.0 Hz
(Rate)
[tri], [SqU], [Sin],
COLOR
(Wave Type) [SW1], [SW2]
SW1
R
L
0–127
RATE (DEPTH)
(Depth)
LEVEL -15– +15
(EQ Gain)
AUTO PAN SYNC (Sync type)
Auto Pan synchronized to the BPM. Rate, set with INTENSITY,
changes according to the note length corresponding to the BPM setting.
Parameter Value
INTENSITY note *1 (p. 112)
(Rate)
COLOR * Same as "AUTO PAN"
(Wave Type)
RATE (DEPTH)
(Depth)
LEVEL
(EQ Gain)
How to Set the BPM Sync Start Timing (p. 112)
2-VOICE PITCH SHIFTER
Shifts the pitch of the original sound. You can have two pitch-shifted
sounds played, one above and one below the original sound, and
change the difference between them.
fig.2VcPchShift
L in
Pitch Shift A
2-Voice Pitch Shifter
Pitch Shift B
R in
Parameter Value
INTENSITY 0–127
(Pitch)
COLOR [Fin], [Coa]
(Pitch Mode)
RATE (DEPTH) 0–350 ms
(Pre Delay)
LEVEL 0–100
(Balance)
L out
EQ
R out
EQ
Description
Frequency of the change
Selects the way the positioning
of the sound is changed.
[tri]: triangle wave
[SqU]: square wave
[Sin]: sine wave
[SW1/2]: sawtooth wave
SW2
R
L
Depth to which the effect is ap-
plied
+: High boost
-: Low boost
Description
Frequency of the change
Balance D
L out
Balance W
Balance W
R out
Balance D
Description
Amount of pitch shift
Smoothness of the change in pitch
[Fin]: Continuous, [Coa]: Semitone steps
Adjusts the time until the pitch shifted
sound is heard.
Relative amount of pitch-shifted sound
FEEDBACK PITCH SHIFTER
This allows the pitch-shifted sound to be fed back into the effect.
fig.FbkPchShift
L in
Balance D
Pitch Shifter
Feedback
R in
Balance D
Parameter Value
INTENSITY 0–127
(Pitch)
COLOR [Fin], [Coa]
(Pitch Mode)
RATE (DEPTH) 0–350 ms
(Pre Delay)
LEVEL -98– +98%
(Feedback)
STEREO DELAY
This is a stereo delay.
fig.StDELAY
Balance D
L in
Delay
Feedback
Feedback
Delay
R in
Balance D
Parameter Value
INTENSITY 0.0–240 ms
(Delay Time)
COLOR 200 Hz–8 kHz,
(HF Damp) byP
RATE (DEPTH) -98– +98%
(Feedback)
LEVEL 0–100
(Balance)
STEREO DELAY SYNC (Sync type)
Stereo Delay synchronized to the BPM. Delay Time, set with
INTENSITY, changes according to the note length corresponding to
the BPM setting.
Parameter Value
INTENSITY note *1
(Delay Time) (p. 112)
COLOR * Same as "STEREO DELAY"
(HF Damp)
RATE (DEPTH)
(Feedback)
LEVEL
(Balance)
How to Set the BPM Sync Start Timing (p. 112)
Effects List
L out
Balance W
Balance W
R out
Description
Amount of pitch shift
Smoothness of the change in pitch
[Fin]: Continuous, [Coa]: Semitone steps
Adjusts the time until the pitch shifted
sound is heard.
Adjusts the amount of the pitch-shifted
sound that's fed back into the effect.
Negative (-) settings invert the phase.
L out
Balance W
Balance W
R out
Description
Adjusts the time until the delay
sound is heard.
Adjusts the frequency above which
sound fed back to the effect is fil-
tered out.
If you don't want to filter out any
high frequencies, set this parameter
to byP.
Adjusts the amount of the delay
sound that's fed back into the effect.
Negative (-) settings invert the
phase.
Relative amount of delay sound
Description
Adjusts the time until the delay
sound is heard.
111