Save the carton and all packing materials. In the event that a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing. Your shipment includes: ● Showtec Ignitor-6 Section Strobe wit 0,75m Schuko power cable ● User manual LED Expected Lifespan LEDs gradually decline in brightness over time.
Page 4
● If your Showtec device fails to work properly, discontinue the use immediately. Pack the unit securely (preferably in the original packing material), and return it to your Showtec dealer for service.
The installation must always be secured with a safety attachment, e.g. an appropriate safety net or safety cable. ● When rigging, derigging or servicing the device, always make sure, that the area below the installation site is secured and that there are not any unauthorized people around. Ordercode: 40292...
UK Cable US Cable BROWN YELLOW/COPPER PHASE BLUE BLACK SILVER NEUTRAL YELLOW/GREEN GREEN GREEN PROTECTIVE GROUND Make sure that the device is always properly connected to the earth! Improper installation can cause serious injuries and/or damage of property! Ordercode: 40292...
After this period complaints will not be handled anymore. Complaints will only then be considered if the client has so far complied with all parts of the agreement, regardless of the agreement from which the obligation is resulting. Ordercode: 40292...
Ignitor-6 Section Strobe Description of the device Features The Showtec Ignitor-6 Section Strobe is a strobe effect with high output and great effects. ● Total control of all individual strobe sections ● Reflectors have been improved to give more output ●...
Before plugging the unit in, always make sure that the power supply matches the product specification voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa. Connect the device to the main power supply. The device can be sound-controlled as it is equipped with a built-in microphone. Ordercode: 40292...
Programs or Music control Mode). This means on the master device you can set your desired operation Mode and all slave devices will react the same as the master device. Multiple Ignitor-6 Section Strobes (Master/Slave control) Fig. 03 Ordercode: 40292...
Do not supply power before the whole system is set up and connected properly. Multiple Ignitor-6 Section Strobes DMX Set Up Fig. 04 Note : Link all cables before connecting electric power Ordercode: 40292...
FL09150 (1,5 m), FL093 (3 m), FL096 (6 m), FL0910 (10 m), FL0915 (15 m), FL0920 (20 m). ● DAP Audio DMX adapter: 5-pin/3-pin. Ordercode FLA29. ● DAP Audio DMX adapter: 3-pin/5-pin. Ordercode FLA30. The Ingnitor-6 Section Strobe can be operated with a controller in control mode or without the controller in stand-alone mode. Ordercode: 40292...
When no button is pressed for 30 seconds, the display will turn off. To light up the display, you have to press the MENU, UP, DOWN or ENTER button. Once you have pressed the button, the display will light up. Ordercode: 40292...
01) In main menu, press the UP/DOWN buttons until the display shows 02) Press the ENTER button to enter. The display shows Turn on the music and the Ignitor-6 Section Strobe will react to the beat of the music. Ordercode: 40292...
8. Version Number With this menu you can see the current software version. 01) In main menu, press the UP/DOWN buttons until the display shows 02) Press the ENTER button to show your software version number: Version V1.0 Ordercode: 40292...
Channel 6 – Dimmer Part 6 0-255 Brightness from 0 to 100% Channel 7 – Strobe 0-10 No Function 11-255 Flash frequency from slow to fast Channel 8 – Running Light 0-10 No Function 11-255 Speed from slow to fast Ordercode: 40292...
Response: Suspect three potential problem areas as: the power supply, the LEDs, the fuse. 01) Power supply. Check that the unit is plugged into an appropriate power supply. 02) The LEDs. Return the Ignitor-6 Section Strobe to your Showtec dealer. 03) The fuse. Replace the fuse. See page 15 for replacing the fuse.
Page 19
No light or lLEDs LEDs damaged • Disconnect the fixture and return it cuts out to your dealer intermittently The power supply settings do not • Disconnect fixture. Check settings match local AC voltage and and correct if necessary frequency Ordercode: 40292...