Related Manuals for SHOWTEC Phantom 25MKII Spot LED
Summary of Contents for SHOWTEC Phantom 25MKII Spot LED
- Page 1 MANUAL ENGLISH Phantom 25MKII Spot LED V1 Ordercode: 40204 Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands...
-
Page 2: Table Of Contents
Phantom 25MKII LED Spot Table of contents Warning ....................................3 Safety Instructions ................................. 3 Operating Determinations ............................5 Rigging .................................... 5 Mounting a bracket to the underside of the Phantom 25 MKII LED Spot............5 Connection with the mains............................6 Return Procedure ................................ - Page 3 Phantom 25MKII LED Spot Product Specifications ..............................26 Dimensions ..................................27 Notes ....................................28 Ordercode: 40204...
-
Page 4: Warning
Save the carton and all packing materials. In the event that a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing. Your shipment includes: ● Showtec Phantom 25MKII LED Spot ● Mounting bracket with 2 mounting screws ●... - Page 5 If your Showtec device fails to work properly, discontinue use immediately. Pack the unit securely (preferably in the original packing material), and return it to your Showtec dealer for service.
-
Page 6: Operating Determinations
Phantom 25MKII LED Spot Operating Determinations This device is not designed for permanent operation. Consistent operation breaks will ensure that the device will serve you for a long time without defects. The minimum distance between light-output and the illuminated surface must be more than 1 meter. ... -
Page 7: Connection With The Mains
Phantom 25MKII LED Spot The Phantom can be placed on a flat stage floor or mounted to any kind of truss by means of the mounting bracket. Improper installation can cause serious damage to people and property! Connection with the mains Connect the device to the mains with the power-plug. -
Page 8: Return Procedure
Phantom 25MKII LED Spot Return Procedure Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued. Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility. Call Highlite 0031-455667723 or mail aftersales@highlite.nl and request an RMA prior to shipping the fixture. -
Page 9: Description Of The Device
Phantom 25MKII LED Spot Description of the device Features The Showtec Phantom 25MKII LED Spot is a moving-head with high output and great effects. DMX-control via standard DMX-controller Built-in Automatic Programs + Built-in Sound activated programs User-selectable Pan & Tilt ranges ... -
Page 10: Overview
Phantom 25MKII LED Spot Overview Fig. 01 01) 1x 25W White LED (Lens has manual focus) 02) Cooling fan 03) Menu buttons and LED Display Ordercode: 40204... -
Page 11: Backside
Phantom 25MKII LED Spot Backside Fig. 02 04) IEC power connector IN 05) IEC power connector OUT 06) Fuse F2A / 250V 07) 3-pin DMX signal connector IN 08) 3-pin DMX signal connector OUT Installation Remove all packing materials from the Phantom 25MKII LED Spot. Check if all foam and plastic padding is removed. -
Page 12: Control Modes
Phantom 25MKII LED Spot Control Modes There are 4 modes: • Built-in programs • Sound-controlled • Master/Slave Mode • DMX-512 (6CH, 11CH) One Phantom (Built-in Programs) 01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation. 02) Always use a safety cable (ordercode 70140 / 70141). -
Page 13: Multiple Phantoms (Dmx Control)
Phantom 25MKII LED Spot Multiple Phantoms (DMX Control) 01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation. 02) Always use a safety cable (ordercode 70140 / 70141). 03) Use a 3-pin XLR cable to connect the Phantoms and other devices. 04) Link the units as shown in (Fig.04), Connect a DMX signal cable from the first unit's DMX "out"... -
Page 14: Fixture Linking
Phantom 25MKII LED Spot Fixture Linking You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to run synchronized shows on two or more fixtures set to a master/slave operating mode. The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support. -
Page 15: Control Panel
Phantom 25MKII LED Spot Control Panel A) LED display Mode/ESC button C) Up button D) Down button Enter button Fig. 05 DMX Control Mode The fixtures are individually addressed on a data-link and connected to the controller. The fixtures respond to the DMX signal from the controller. (When you select the DMX address and save it, the controller will display the saved DMX address the next time.) DMX Addressing The control panel on the front side of the base allows you to assign the DMX fixture address, which is the... -
Page 16: Menu Overview
Phantom 25MKII LED Spot Menu Overview Ordercode: 40204... -
Page 17: Main Menu Options
Phantom 25MKII LED Spot Main Menu Options DMX address Device mode Pan mode Tilt mode Display DMX configuration Pan configuration Tilt configuration Reset Load factory default settings 1. DMX Address With this menu you can set the DMX address. 01) Press the Mode/ESC button until the display shows 02) Press the Enter button to confirm. -
Page 18: Built-In Program Slow
Phantom 25MKII LED Spot 2.1 Built-in program slow 01) Press the Up/Down buttons until the display shows 02) Press the Enter button to confirm, the display will show 03) The device will start its slow built-in program immediately. 2.2 Built-in program fast 01) Press the Up/Down buttons until the display shows 02) Press the Enter button to confirm, the display will show 03) The device will start its fast built-in program immediately. -
Page 19: Pan Configuration
Phantom 25MKII LED Spot 7. Pan configuration With this menu you can set the pan configuration. 01) Press the Mode/ESC button until the display shows 02) Now the pan is 540º. 03) Press the Up/Down buttons to choose from 540º, 360ºor 180º. 8. -
Page 20: Dmx Channels
Phantom 25MKII LED Spot DMX Channels 11 Channels Channel 1 – Horizontal movement (Pan) Push the slider up, in order to move head horizontally (PAN). Gradual head adjustment, between 0-255. The head can be turned by 540° and stopped at any position you wish. - Page 21 Phantom 25MKII LED Spot Channel 9 – Static Gobo-wheel + Gobo shake (CH6 and CH8 must be set between 001-255 and CH7 between 4-255 Open / White 6-11 Metal Gobo 1 12-17 Metal Gobo 2 18-23 Metal Gobo 3 24-29 Metal Gobo 4 30-35 Metal Gobo 5...
-
Page 22: Channels
Phantom 25MKII LED Spot 168-183 Sound-controlled Program 3 184-199 Sound-controlled Program 4 200-215 Sound-controlled Program 5 216-231 Sound-controlled Program 6 232-247 Sound-controlled Program 7 248-255 Sound-controlled Program 8 6 Channels Channel 1 – Horizontal movement (Pan) Push the slider up, in order to move head horizontally (PAN). Gradual head adjustment, between 0-255. -
Page 23: Channel Settings
Phantom 25MKII LED Spot Channel 6 – Static Gobo-wheel + Gobo shake (CH3 and CH5 must be set between 001-255 and CH4 between 4-255 Open / White 6-11 Metal Gobo 1 12-17 Metal Gobo 2 18-23 Metal Gobo 3 24-29 Metal Gobo 4 30-35 Metal Gobo 5... -
Page 24: Maintenance
Phantom 25MKII LED Spot Maintenance The Showtec Phantom 25MKII LED Spot requires almost no maintenance. However, you should keep the unit clean. Otherwise, the fixture’s light-output will be significantly reduced. Disconnect the mains power supply, and then wipe the cover with a damp cloth. Do not immerse in liquid. Wipe lens clean with glass cleaner and a soft cloth. -
Page 25: Troubleshooting
18). 02) Power supply. Check if the unit is plugged into an appropriate power supply. 03) The LED. Return the Phantom to your Showtec dealer. 04) The fuse. See page 23 for replacing the fuse 05) If all of the above appears to be O.K., plug the unit in again. - Page 26 Phantom 25MKII LED Spot Problem Probable cause(s) Remedy One or more No power to the fixture. ● Check that power is switched on and fixtures are cables are plugged in. completely dead. Primary fuse blown. ● Replace fuse. Fixtures reset The controller is not connected.
- Page 27 Phantom 25MKII LED Spot Product Specifications Model: Showtec Phantom 25MKII LED Spot Input Voltage: 100-240 VAC, 50/60Hz Power consumption: 70W max. at full output DMX linking: 30pcs Fuse: F2A / 250V Dimensions: 210 x 205 x 302 mm (LxWxH) Weight:...
- Page 28 Phantom 25MKII LED Spot Dimensions Ordercode: 40204...
- Page 29 Phantom 25MKII LED Spot Notes Ordercode: 40204...
- Page 30 Phantom 25MKII LED Spot Ordercode: 40204...
- Page 31 Phantom 25MKII LED Spot Ordercode: 40204...
- Page 32 ©2016 Showtec...