Table of Contents
Related Manuals for IDT Tsi340-RDK1
Summary of Contents for IDT Tsi340-RDK1
-
Page 1: User Manual
Tsi340 Evaluation Board User Manual 80E3000_MA002_02 September 19, 2009 6024 Silver Creek Valley Road San Jose, California 95138 Telephone: (408) 284-8200 • FAX: (408) 284-3572 Printed in U.S.A. ©2009 Integrated Device Technology, Inc. - Page 2 IDT does not assume responsibility for use of any circuitry described herein other than the circuitry embodied in an IDT product. Disclosure of the information herein does not convey a license or any other right, by implication or otherwise, in any patent, trademark, or other intellectual property right of IDT. IDT products may contain errata which can affect product performance to a minor or immaterial degree.
-
Page 3: Revision History
In the board layout section the component placement and the setting options are explained. 1.1.1 Evaluation Board Part Number The Tsi340 evaluation board part number is Tsi340-RDK1 V1.0. The assembly number of the board is E3000_AS001. Integrated Device Technology Tsi340 Evaluation Board User Manual www.idt.com... -
Page 4: Functional Description
Form Factor: 4-layers Micro ATX Add-in Card with extended height • Size: ~5.5” x 7.5” 1.1.2.5 Power Supply • PCI Finger Edge Connector: +3.3 V, +5 V, +12 V, -12 V • Maximum Power Consumption: 25 W Tsi340 Evaluation Board User Manual Integrated Device Technology 80E3000_MA002_02 www.idt.com... -
Page 5: Board Design
3.3V 32Bit PCI Thru-Hole Connector Slot C 3.3V 32Bit PCI Thru-Hole Connector Slot D DIPSWITCH 5.0V SETTING Secondary Interface 3.3V Tsi340 PCI-to-PCI Bridge Primary Interface 66MHz 3.3V/5V 32Bit PCI Finger Edge Connector Integrated Device Technology Tsi340 Evaluation Board User Manual www.idt.com 80E3000_MA002_02... - Page 6 A DIP switch is attached to M66EN that is used to force M66EN to ground so that the 33 MHz PCI clock can be set. Refer to “DIP Switch Package/ Individual Switch Position” on page 14 for more information. Tsi340 Evaluation Board User Manual Integrated Device Technology 80E3000_MA002_02 www.idt.com...
- Page 7 When plug-in cards are added to the Tsi340 evaluation board, the current draw must not exceed the capacity of the finger connector. The maximum current draw per rail for the bridge board with cards plugged-in is indicated in Table Integrated Device Technology Tsi340 Evaluation Board User Manual www.idt.com 80E3000_MA002_02...
- Page 8 The finger connector PRSNT[1:2] pins are wired to indicate a power requirement of 25 W. This is the maximum power the PRSNT[1:2] pins can indicate for an add-in card. The PRSNT pin on the secondary side connectors is not used. Tsi340 Evaluation Board User Manual Integrated Device Technology 80E3000_MA002_02 www.idt.com...
- Page 9 Remove the R1, R2, R3 resistors • Solder jumper wires (AWG22) between the 5V test pads and the SVIO test pads. Figure 3: Modified PCB Traces for 5 V Signaling on Secondary PCI Bus Integrated Device Technology Tsi340 Evaluation Board User Manual www.idt.com 80E3000_MA002_02...
- Page 10 Resets Tsi340 is reset from the system host reset signal (from the finger connector). The secondary side reset is driven by Tsi340. There is no manual reset on the board. Tsi340 Evaluation Board User Manual Integrated Device Technology 80E3000_MA002_02 www.idt.com...
-
Page 11: Board Layout
Layer 1: PCB primary side (where most traces are routed) • Layer 2: Ground plane • Layer 3: Power plane • Layer 4: Secondary side Figure 4 shows the four layers of the PCB. Figure 4: PCB Stack Up Integrated Device Technology Tsi340 Evaluation Board User Manual www.idt.com 80E3000_MA002_02... -
Page 12: Board Dimensions
The board dimensions are based on PCI standard for a 32-bit Variable Height Short Add-in card. However, the height of the card exceeds the maximum specified in the standard. The board dimensions are shown in Figure Figure 5: Board Dimensions 5.5” 7.87” Tsi340 Evaluation Board User Manual Integrated Device Technology 80E3000_MA002_02 www.idt.com... -
Page 13: Component Placement
Component Placement The placement of the components, jumpers, and switches are shown in Figure Figure 6: Component Placement Integrated Device Technology Tsi340 Evaluation Board User Manual www.idt.com 80E3000_MA002_02... - Page 14 PCI_CLKin and PCI_M66EN# signal level from the secondary plug-in cards) Tsi340 S_CLKRUN# input pin ON: S_CLKRUN# is pulled down for normal operation. connection OFF: S_CLKRUN# is pulled up for test purpose only. Unused Unused Unused Tsi340 Evaluation Board User Manual Integrated Device Technology 80E3000_MA002_02 www.idt.com...
- Page 15 J1 through J4 Connectors - PCI Plug-in Card J1, J2, J3, J4 are used to connect plug-in card on Tsi340’s secondary PCI side. The connector’s pin assignment is standard PCI 32-bit, 3.3 V connectors. Integrated Device Technology Tsi340 Evaluation Board User Manual www.idt.com 80E3000_MA002_02...
- Page 16 Table 11 shows the pin assignments for the J5 connector. Table 7: J7 Pin Assignment Signal Assignment J7 pin location 3.3V 3.3V 3.3V -12V Tsi340 Evaluation Board User Manual Integrated Device Technology 80E3000_MA002_02 www.idt.com...
-
Page 17: Test Points
The bridge board can plug into a 3.3 V or 5 V systems. The primary side input/output signaling uses the same voltage as the system. The secondary side voltage is independent of the primary side voltage. Integrated Device Technology Tsi340 Evaluation Board User Manual www.idt.com 80E3000_MA002_02... - Page 18 RES SMT, 4.7 KOHM, 0.1W, R16,R18-27,R29-30, 5%, 0603 R32-34,R36-38, R40-42 R5-7,R17,R47 9C06031A0R00JLHFT YAGEO RES SMT, 0 OHM, 0.1W, 5%, 0603 R9,R11,R13,R15 ERJ-3GEYJ301V PANASONIC RES SMT, 300 OHM, 0.1W, 5%, 0603 Tsi340 Evaluation Board User Manual Integrated Device Technology 80E3000_MA002_02 www.idt.com...
- Page 19 RefDes Part Number Manufacturer Description R43-46 ERJ-3GEYJ330V PANASONIC RES SMT, 33 OHM, 0.1W, 5%, 0603 2-1437590-2 TYCO DIPSWITCH, 8 SWITCHES TP1-16 TESTPOINT Test points TSI340-66CQ PCI TO PCI BRIDGE, 32BITS/66MHZ Integrated Device Technology Tsi340 Evaluation Board User Manual www.idt.com 80E3000_MA002_02...
- Page 20 CORPORATE HEADQUARTERS for SALES: for Tech Support: 6024 Silver Creek Valley Road 800-345-7015 or 408-284-8200 email: ssdhelp@idt.com San Jose, CA 95138 fax: 408-284-2775 phone: 408-284-8208 www.idt.com document: 80E3000_MA002_02 September 19, 2009...
Need help?
Do you have a question about the Tsi340-RDK1 and is the answer not in the manual?
Questions and answers