Lightware MMX4x2-HDMI Quick Start Manual page 2

Front Panel Operation
Video Select Buttons
Use the buttons for selecting the video input source. The sequence is the following for each
device.
MMX4x2-HDMI:
HDMI IN 1 HDMI IN 2 HDMI IN 3 HDMI IN 4
MMX4x2-HT200:
TPS IN 1 HDMI IN 2 HDMI IN 3 HDMI IN 4
Set Audio Config Button
Use the button to select the audio configuration mode. The sequence is:
#1 #2 #3 #4
#1: Copy HDMI OUT 1 audio to HDMI OUT 2 and AUDIO OUT.
#2: Copy HDMI OUT 2 audio to HDMI OUT 1 and AUDIO OUT.
#3: Use audio from Analog Input on all outputs.
#4: Keep Original Audio on HDMI outputs, de-embed from HDMI OUT 2 to Analog Audio
Output.
Software Control – Using Lightware Device Controller (LDC)
The device can be controlled from a computer through the Ethernet, RS-232,
and USB ports using Lightware Device Controller. Please download the
application from www.lightware.com, install on a Windows PC or a Mac OS X
and establish connection to the device.
 The default IP address of the device is: 192.168.0.100, DHCP is disabled.
Set Dynamic IP Address (DHCP)
1. Keep the Set Audio Config button pressed for 5 seconds; all front panel LEDs start to blink.
2. Release the button, then press it 3 times quickly. DHCP is now enabled.
Restore Factory Default Settings
1. Keep the Set Audio Config button pressed for 10 seconds; after 5 seconds front panel LEDs
start to blink but keep the button pressed; the LEDs start to blink faster 5 seconds later.
2. Release the button, then press it 3 times quickly; factory default settings are restored:
Network settings
IP address (static) 192.168.0.100
Subnet mask 255.255.255.0
Static gateway 192.168.0.1
DHCP Disabled
TCP/IP port nr. LW2 / LW3 10001 / 6107
Video crosspoint settings
O1 (HDMI out 1) - MMX4x2-HDMI I1 (HDMI in 1)
O1 (HDMI out 2) - MMX4x2-HT200 I1 (TPS in 1)
O2 (HDMI out 2) - for both models I2 (HDMI in 2)
Audio crosspoint settings
O1 (HDMI out 1) A1 (original HDMI embedded audio)
O2 (HDMI out 2) A2 (original HDMI embedded audio)
O3 (Audio out) A3 (analog audio input)
Port properties
Autoselect Disabled
Input TPS mode Auto
Emulated EDID on all four inputs Factory #47: Universal HDMI PCM
RS-232 settings
RS-232 mode Control
Control protocol LW2
Port setting 57600 BAUD, 8, N, 1
Command injection port (local/link) 8001 / 8002
Typical Application
Standalone layout - MMX4x2-HDMI
E T
R N
Autoselect
H E
E T
Autoselect
12V DC
Power
adaptor
Typical Application
Standalone layout - MMX4x2-HT200
VGA
Analog audio
HDMI
VGA
Laptop
DisplayPort
HDMI Laptop
UMX-TPS-TX140
MacBook
MMX4x2-HT200
Port Diagram
Analog
audio in
HDMI in 2
HDMI in 3
HDMI in 4
TPS in 1
Remote
control
IR detector
IR
LAN
RS-232
Volume
IR control
T
OU
AU DIO
HD CP
Analog NA L
SIG
HD CP 2
L OU T
SIG NA HD MI
audio OU T 1
MI
HD
L
NA
SIG Analog
L IN 4
NA HD MI
SIG
L IN 3
NA HD MI audio
SIG
L 2
NA MI IN
m SIG HD
: 2m IN 1
PIN HD MI
DC _ HDMI
12V ---
1.5A
HDMI
HDMI
HDMI
IR emitter
Videoconference
codec
HDMI
Media player
Laptop
IR detector
RS-232
IR
LAN
E T
R N
H E
E T
Analog
audio
NAL
SIG
NAL
SIG HDM
3
NAL I IN
SIG HDM
I IN 2
HDM
: 2m m
PIN (PoE )
IN 1
DC _ TPS
12V ---
1.5A
12V DC
Power
adaptor
TPS
IN
2 IN DV I-I
AU DIO
(up to 170 m)
RS-2 LIVE 32 C
SRV OUT
LINK IN IR
IR
)
(PoE
TPS OUT
IO
GP
2
RS -23
mm
: 2.1
12V DC PIN RX TX
DC
12V 1A
Power
adaptor
Analog Analog
Digital audio
audio audio
A/D D/A
converter converter
3x3 Digital
4x2 HDMI audio Digital
crosspoint
crosspoint
audio
Digital video
Digital
Digital video
HDMI video
reclocker
Digital
Digital video HDMI video
reclocker
HDBaseT
TM
receiver
Processor
Maximum Extension Distances for MMX4x2-HT200
1024x768@60Hz
HDMI
1280x720p@60Hz
1920x1080p@60Hz (24bpp)
4K monitor
1920x1200@60Hz
1600x1200@60Hz
Active speakers
1920x1080@60Hz (36bpp)
3840x2160@30Hz UHD
4096x2160@30Hz 4K
* Long reach TPS mode supports pixel clock frequencies up to 148.5 MHz.
 CAT7 SFTP AWG23 cable is always recommended.
Audio Cable Wiring Guide
MMX4x2 series matrix is built with 5-pole Phoenix input and output connectors. See below a
few example of the most common assembling cases.
Remote
From balanced output to unbalanced input
control
Volume
MMX4×2-HT200
control
Analog
OUT
IO
AUD
HDC P audio
SIG NAL
HDC P 2
I OUT
SIG NAL HDM
1
I OUT
HDM
HDMI Active
I IN 4
speakers
HDMI
4K monitor
From balanced output to balanced input
HDMI
Videoconference
codec
AUDIO Output
PC
From balanced output to unbalanced input
Analog
audio out
HDMI out 1
HDMI out 2
From balanced output to unbalanced input
IR out
IR in
RS-232
Ethernet
For more information about audio cable wiring see the user's manual of the device or the Audio
USB
Cable Wiring Guide on our website www.lightware.com.
control
Cable lengths
(Auto / Long reach TPS mode)
Pixel
Resolution
clock rate
CAT5e CAT7 CAT7
AWG24 AWG26 AWG23
65 MHz 100 m / 130 m* 90 m / 120 m* 120 m / 170 m*
73.8 MHz 100 m / 130 m* 90 m / 120 m* 120 m / 170 m*
148.5 MHz 100 m / 130 m* 90 m / 120 m* 120 m / 170 m*
152.9 MHz 100 m / NA 90 m / NA 120 m / NA
162 MHz 100 m / NA 90 m / NA 120 m / NA
223 MHz 70 m / NA 70 m / NA 100 m / NA
297 MHz 70 m / NA 70 m / NA 100 m / NA
297 MHz 70 m / NA 70 m / NA 100 m / NA
From unbalanced output to balanced input
Phoenix - 3.5 (1/8") TRS 3.5 (1/8") TRS - Phoenix
From balanced output to balanced input
Phoenix - 2 x XLR 2 x XLR - Phoenix
2 2
2 2
3 3
3 3
AUDIO Input
From unbalanced output to balanced input
Phoenix - 2 x 6.3 (1/4") TS 2 x 6.3 (1/4") TS - Phoenix
From unbalanced output to balanced input
Phoenix - 2 x RCA 2 x RCA - Phoenix