Front Sensing Type - Panasonic EX-Z Series User Manual

8-2 Front sensing type

Type
NPN output
Model No.
(Note 2) PNP output EX-Z11FA-P EX-Z11FB-P EX-Z12FA-P EX-Z12FB-P EX-Z13FA-P EX-Z13FB-P
Sensing distance
Minimum sensing
object
Repeatability
(Perpendicular to sensing axis)
Supply voltage
Current consumption
Output
Short-circuit protection
Response time
Protection
Ambient temperature
Ambient humidity
Ambient illuminance
Voltage withstandability 1,000V AC for one min. between all supply terminals connected together and enclosure
Insulation resistance
Vibration resistance 10 to 500Hz frequency, 3mm amplitude (20G max.) in X, Y and Z directions for two hours each
Shock resistance
Emitting element
Material
Cable (Note 3)
Cable extension
Weight (Main body only)
Accessories
Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient
temperature of +23 °C.
2) The model No. with suffix "E" shown on the label affixed to the thru-beam type sensor is the emitter,
"D"shown on the label is the receiver.
(Example) Emitter of EX-Z11FA: EX-Z11FE, Receiver of EX-Z11FA: EX-Z11FAD
Model Nos. having suffix "-R" are inflection resistant cable type.
(Example) The inflection resistant cable type of EX-Z11FA-P is "EX-Z11FA-P-R".
3) The inflection resistant cable type (model having "-R" at its end of the model No.) is 0.1mm
(emitter: 2-core) cabtyre cable, which is 2m long.
14
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
Sensing distance 50mm type Sensing distance 200mm type Sensing distance 500mm type
Light-ON Dark-ON
EX-Z11FA EX-Z11FB
50mm
ø0.3mm opaque object (Com-
pletely beam interrupted ob-
ject) (Setting distance between
emitter and receiver: 50mm)
0.02mm or less
12 to 24V DC ±10% Ripple P-P 10% or less
Emitter: 10mA or less, Receiver: 10mA or less
<NPN output type>
NPN open-collector transistor
• Maximum sink current: 20mA
• Applied voltage: 30V DC or less
(between output and 0V)
• Residual voltage: 1.5V or less
(at 20mA sink current)
-10 to +55°C (No dew condensation or icing allowed), Storage: -30 to +70°C
35 to 85% RH, Storage: 35 to 85% RH
Incandescent light: 5,000ℓx at the light-receiving face
20MΩ, or more, with 250V DC megger between all supply terminals connected together
2
500m/s acceleration (50G approx.) in X, Y and Z directions for three times each
Red LED (Peak emission wavelength: 650nm)
Enclosure: PBT, Lens: Polycarbonate, Metallic part: Stainless steel (SUS304, Rear part: SUS301)
2
0.1mm 3-core (emitter: 2-core) cabtyre cable, 2m long
Extension up to total 50m is possible with 0.3mm
emitter and receiver).
Each of emitter and receiver: Approx. 15g
M2 screw (length 6mm): 2 pcs., Nut: 2 pcs., Spring washer: 2 pcs., Flat washer: 2 pcs.
Instruction manual: 1 pc.
Light-ON Dark-ON
EX-Z12FA EX-Z12FB
200mm
ø0.5mm opaque object (Com-
pletely beam interrupted ob-
ject) (Setting distance between
emitter and receiver: 200mm)
0.03mm or less
<PNP output type>
PNP open-collector transistor
• Maximum source current: 20mA
• Applied voltage: 30V DC or less
• Residual voltage: 1.5V or less
Incorporated
0.5ms or less
IP67 (IEC)
and enclosure
2
, or more, cable (thru-beam type:
Light-ON Dark-ON
EX-Z13FA EX-Z13FB
500mm
ø1.0mm opaque object (Com-
pletely beam interrupted ob-
ject) (Setting distance between
emitter and receiver: 500mm)
0.05mm or less
(between output and +V)
(at 20mA source current)
2
3-core