ARTiGO-A1150
Quick Guide
Key Features:
•
Space saving, ultra compact design
•
Onboard Gigabit Ethernet
•
Four USB 2.0 host and one USB Device port
•
One HDMI
®
and one VGA ports
•
One drive bay for 2.5-inch SATA hard disk drive or SSD
•
SD card reader and WLAN module (optional)
P/N: 99G51-013094-10
Installing the Memory
1
Step 1
Locate the memory access cover on the bottom side of the
ARTiGO-A1150 and remove the screw.
Step 2
Remove the memory access cover as indicated in the figure below.
The ARTiGO-A1150 is an ultra compact embedded system. It's based
on the VIA EPIA-P900 Pico-ITX form factor and powered by a high
performance VIA Eden™ X2 processor. The ARTiGO-A1150 is de-
signed with elegant chassis with dual I/O access plates for easy inte-
gration and quick setup.
Specifications:
CPU:
•
VIA Eden™ X2 1.0GHz processor (800 MHz FSB)
System Chipset:
•
VIA VX900 Unified Digital Media IGP chipset
System Memory:
•
1 x DDR3 1066 MHz SDRAM SODIMM slot
•
Supports memory sizes up to 4 GB
Graphics:
•
Integrated VIA C-9 HCM DX9 3D/2D AGP graphics with MPEG-2,
H.264 and WMV9/VC1 video decoding accelerator
Storage:
•
•
1 x 2.5-inch SATA hard disk drive bay
•
1 x SD card reader (optional)
LAN:
•
VIA VT6130G Gigabit Ethernet controller
Audio:
•
VIA VT2021 High Definition Audio Codec
System Indicator:
•
•
Power Status (green LED)
•
Hard Disk Drive Activity (red LED)
BIOS:
•
AMI BIOS
8 Mbit LPC Flash Memory
•
Step 3
Insert the memory module into the SODIMM socket at the 45
degree angle. Then push down until the memory module snaps
into place. The SODIMM socket has two locking mechanisms that
will click once the memory module has been fully inserted.
1
2
Step 4
Reinstall the memory access cover and secure it with screw.
Front I/O:
•
•
2 x USB 2.0 host ports
•
1 x USB device port
•
3 x Audio jacks (Line-out, Line-in & Mic-in)
•
Rear I/O:
•
1 x VGA connector
•
2 x USB 2.0 host ports
•
1 x HDMI
®
port
•
1 x RJ45 port (Gigabit Ethernet connection)
•
DC 12V Power Input connector
•
Side I/O
•
1 x SD slot (optional)
•
Dimensions:
146 mm (W) x 52 mm (H) x 99 mm (D)
Weight:
0.6 Kg (1.32 lbs)
•
Operating Temperature:
•
0°C up to 45°C
Storage Temperature:
•
-10°C ~ 60°C
Humidity:
•
0% ~ 90% relative humidity (non-condensing) @ 45°C
Packing List:
•
1 x ARTiGO-A1150 system
•
1 x AC-to-DC adapter, DC 12V/5A, 60W
•
1 x Power cable, 180 cm
•
1 x Quick Guide
Important:
Please ensure that all items in the packing list are present before using
this product. If any of the items are missing or damaged, contact your
distributor or sales representative immediately.
Hard disk drive, CompactFlash disk, Flash SSD drive, SD card reader
module and SD card, wireless LAN module, system memory module
and operating system must be purchased separately.
Opening the
2
Top Cover Chassis
Step 1
Remove the screw of the top cover from the rear side of the
ARTiGO-A1150.
Step 2
Then gently slide the top cover backward and lift off the top
cover as indicated in the figure below.
Front I/O Layout
USB port 2
USB port 1
Power button
5
Inspired by Pico-ITX
Power LED
HDD LED
Line-in
Line-out
Mic-in
Mini USB port
Rear I/O Layout
USB port 3
USB port 4
LAN port
DC IN 12V
HDMI
VGA port
HDMI port
Power port
Side I/O Layout
SD
SD Card slot
Installing the
3
SATA 2.5" Hard Disk
Step 1
On the bottom side of the top cover, remove the SATA 2.5" hard
disk cover plate by unscrewing the four screws.
Step 2
Attach the hard disk plate to the 2.5-inch SATA hard disk by
aligning the mounting holes on the SATA 2.5" hard disk with the
mounting holes on the hard disk cover plate. Then secure the
hard disk in place with four screws.