User Set Mode - Icom IC-G88 Operating Manual

4
SET MODES
VFO Set mode
The VFO Set mode enables you to change various settings for the operation in the VFO mode. You can change the
operating condition in this mode.
Entering the VFO Set mode:
➥ Push [VFO / User Set Mode] to enter the VFO Set mode.
• While in the VFO Set mode, push [
Mode
] again to select an item, and then change the
value or setting by pushing [UP] or [DOWN].
Tuning Step
When you select the operating
frequency by pushing [UP] or
[DOWN], the frequency changes in this selected
tuning step.
The set tuning step is also used for a VFO scan.
• Select 5, 10, 12.5, 15.0, 20.0, 25.0, 30.0 or 50.0. (in kHz)
Frequency offset
Sets the frequency offset for the
duplex operation.
In the duplex mode, the transmit
frequency shifts up or down from the receive fre-
quency by the offset amount.
When the Reverse Duplex is set to OFF, the transmit
frequency shifts from the operating frequency.
When the Reverse Duplex is set to ON, the receive
frequency shifts from the operating frequency.
• Set between 0 ~ 20 (in MHz)
Reverse Duplex
Selects "ON" when reversing
the duplex frequency.
• Select "OF" (OFF) for Normal Duplex communications.
Output Power
Selects the default output
power of each channel.
• Select L1 (Low1: 1 W), L2 (Low2: 2 W) or H (High: 5.5 W).
TIP: Lower output power during short-range communica-
tions may reduce the possibility of interference to
other stations.
Bandwidth
Sets the bandwidth (channel
spacing).
• Select N (Narrow: 12.5 kHz) or W (Wide: 25 kHz).
VFO / User Set
7
Exiting the VFO Set mode:
➥ Hold down [VFO / User Set Mode] again to exit the
VFO Set mode.
Repeater Tone Frequency
Sets the subaudible tone
frequency that is needed to
access the repeater.
Settable frequencies:
67.0 79.7 97.4 118.8
69.3 82.5 100.0 123.0
71.0 85.4 103.5 127.3
71.9 88.5 107.2 131.8
74.4 91.5 110.9 136.5
77.0 94.8 114.8 141.3
Tone Squelch Frequency
Sets the CTCSS tone fre-
quency for the tone squelch
operation.
Settable frequencies:
67.0 79.7 97.4 118.8
69.3 82.5 100.0 123.0
71.0 85.4 103.5 127.3
131.8
71.9 88.5 107.2
74.4 91.5 110.9 136.5
94.8 114.8 141.3
77.0
DTCS Code
Selects the DTCS code for the
DTCS squelch operation.
Settable DTCS codes:
023 054 125 165 251
025 065 131 172 261
026 071 132 174 263
031 072 134 205 265
032 073 143 223 271
036 074 152 226 306
043 114 155 243 311
244
047 115 156 315
116 245
051 162 331
146.2 167.9 186.2 206.5
151.4 171.3 189.9 210.7
156.7 173.8 192.8 218.1
159.8 177.3 196.6 225.7
162.2 179.9 199.5 229.1
165.5 183.5 203.5 233.6
146.2 167.9 186.2 206.5
189.9 210.7
151.4 171.3
156.7 173.8 192.8 218.1
159.8 177.3 196.6 225.7
162.2 179.9 199.5 229.1
165.5 183.5 203.5 233.6
632
343 423 516
654
346 431 532
662
351 432 546
664
364 445 565
703
365 464 606
712
371 465 612
723
411 466 624
731
412
503 627
732
413 506 631
(Continued on the next page.)
241.8
250.3
254.1
241.8
250.3
254.1
734
743
754