Table of Contents
Advertisement
Quick Links
M61323SP/FP
Wide Frequency Band Analog Switch
Description
The M61323SP/FP is a semiconductor integrated circuit for the RGBHV interface. The device features switching
signals input from two types of image sources and outputting the signals to the CRT display, etc. Synchronous signals,
meeting a frequency band of 10 kHz to 200 kHz, are output at TTL. The frequency band of video signals is 250 MHz,
acquiring high-resolution images, and are optimum as an interface IC with high-resolution CRT display and various
new media.
The M61323SP/FP keeps the power saving mode, and it can reduce I
are supplied.
Features
• Frequency band : RGB
H, V
• Input level:
RGB
H, V TTL input
• Only the G channel is provided with Sync-on video output. The TTL format is adopted for HV output.
Application
Display monitor
Recommended Operating Condition
Supply voltage range:
Rated voltage range:
REJ03F0201-0201 Rev.2.01 Mar 31, 2008
Page 1 of 19
CC
250 MHz
10 kHz to 200 kHz
0.7 V
(Typ.)
P-P
3 to 5 V
(bipolar)
O-P
4.75 to 5.25 V
5.0 V
about 10 mA under the condition that all V
REJ03F0201-0201
Rev.2.01
Mar 31, 2008
CC
Advertisement
Table of Contents
Related Manuals for Renesas M61323SP/FP
Summary of Contents for Renesas M61323SP/FP
- Page 1 Wide Frequency Band Analog Switch Description The M61323SP/FP is a semiconductor integrated circuit for the RGBHV interface. The device features switching signals input from two types of image sources and outputting the signals to the CRT display, etc. Synchronous signals, meeting a frequency band of 10 kHz to 200 kHz, are output at TTL.
-
Page 2: Block Diagram
M61323SP/FP Block Diagram M61323SP Output (R) Output (G) Input1 (R) Input1 (G) M61323FP Output (R) Output (G) Input 1 (R) Input 1 (G) Input 1 (B) REJ03F0201-0201 Rev.2.01 Mar 31, 2008 Page 2 of 19 Output Output (B) (G-Buffer) Input1 (B) -
Page 3: Pin Arrangement
M61323SP/FP Pin Arrangement M61323SP 1 (R) Input1 (R) 1 (G) Input1 (G) 1 (B) Input1 (B) Input1 (H) Input1 (V) GND1 Input2 (R) Power Save SW Input2 (G) Input SW Input2 (B) Input2 (H) Input2 (V) (Top view) Outline: PRDP0032BA-A (32P4B) REJ03F0201-0201 Rev.2.01 Mar 31, 2008... -
Page 4: Absolute Maximum Ratings
M61323SP/FP Absolute Maximum Ratings Item Supply voltage Power dissipation Operating temperature Storage temperature Electrostatic discharge Recommended supply voltage Recommended supply voltage range Electrical Characteristics Limits Item Symbol Min. Typ. Max. Unit Circuit current1 Circuit current2 STBY RGB SW Output DC voltage1... - Page 5 M61323SP/FP Electrical Characteristics (cont.) Limits Item Symbol Min. Typ. Max. Unit Freq. characteristic1 (100 MHz) Relative Freq.characteristic1 (100 MHz) Freq.characteristic2 (100 MHz) Relative Freq.characteristic2 (100 MHz) Freq.characteristic3 (250 MHz) Freq.characteristic4 (250 MHz) Crosstalk between C.T.I.1 two inputs1 (10 MHz) Crosstalk between C.T.I.2...
- Page 6 M61323SP/FP Electrical Characteristics (cont.) Limits Item Symbol Min. Typ. Max. Unit HV SW High level Vdch1 output voltage1 High level Vdch2 output voltage2 Low level Vdcl1 output voltage1 Low level Vdcl2 output voltage2 Input threshold VithH voltage H Input threshold...
- Page 7 M61323SP/FP Electrical Characteristics Test Method (M61323SP) Circuit Current 1 No signal. Measure the total circuit current as I Circuit Current 2 No signal. Measure the total circuit current as I Output DC Voltage 1, 2 Set SW13 to GND (or OPEN), measure the DC voltage of TP31 (TP28, TP25) when there is no signal input.
- Page 8 M61323SP/FP Freq. Characteristic 3, 4 Measure the F when SG5 of input signal. (For reference) Crosstalk between Two Inputs 1, 2 1. The conditions is as table. This measurement shall use active probe. 2. Set SW13 to GND, input SG3 to pin 2 only. Read the output amplitude of TP31. The value is as V 3.
- Page 9 M61323SP/FP Pulse Characteristic 1, 2 1. The conditions is as table (SG5 amplitude 0.7 V 2. Measure rising Tri and falling Tfi for 10% to 90% of the input pulse with active probe. 3. Next, measure rising Tro and falling Tfo for 10% to 90% of the output pulse with active probe.
- Page 10 M61323SP/FP <Sync-Separation> Sync Input Minimum Voltage Gradually decreasing the amplitude of SG7 in pin 22, measure the amplitude of SG7 when the Sync-Sep output signal turn off. The value is as SYrv. Sync Output High Level Voltage/Sync Output Low Level Voltage Input SG7 to pin 22, read the output high level and low voltage of TP21.
-
Page 11: Input Signal
M61323SP/FP Input Signal SG No. Sine wave (f = 60 kHz, 0.7 V Sine wave (f = 1 MHz, 0.7 V Sine wave (f = 10 MHz, 0.7 V Sine wave (f = 100 MHz, 0.7 V Sine wave (f = 250 MHz, 0.7 V... - Page 12 M61323SP/FP Test Circuit (M61323SP) 0.01 SW32 TP31 SW B R-OUT R-SW G-SW 0.01 SW A A 5 V REJ03F0201-0201 Rev.2.01 Mar 31, 2008 Page 12 of 19 SW29 SW26 TP28 TP25 G-OUT B-OUT B-SW 0.01 0.01 TP23 SW22 TP21 0.01...
- Page 13 M61323SP/FP Application Example (M61323SP) 0.01 0.01 (5 V) (5 V) 0.01 0.01 INPUT1 Rin1 Gin1 Bin1 Hin1 Vin1 REJ03F0201-0201 Rev.2.01 Mar 31, 2008 Page 13 of 19 Power save (5 V) 0.01 OUTPUT G Buffer Sync SEP Hout Vout POWER SAVE V...
- Page 14 M61323SP/FP Pin Description (M61323SP) pin No. Name DC Voltage (V) (H, V, Sync-Sep.) (ROUT) (GOUT) (BOUT) Input1 (R) Input1 (G) Input1 (B) Input2 (R) Input2 (G) Input2 (B) Input1 (H) Input1 (V) Input2 (H) Input2 (V) GND (V-SW) (H, V, Sync- Sep.)
- Page 15 M61323SP/FP Pin Description (M61323SP) (cont.) pin No. Name DC Voltage (V) PwrSave-SW CONT-SW Vout Hout REJ03F0201-0201 Rev.2.01 Mar 31, 2008 Page 15 of 19 Peripheral Circuit 30 k 15 k 25 k 2.0 V 25 k 20 k 20 k...
- Page 16 M61323SP/FP Pin Description (M61323SP) (cont.) pin No. Name DC Voltage (V) Sync sep OUT Sync sep IN G Buffer OUT Video OUT (B) Video OUT (G) Video OUT (R) REJ03F0201-0201 Rev.2.01 Mar 31, 2008 Page 16 of 19 Peripheral Circuit ...
- Page 17 4. The terminal of R, G, B output pin are shown as figure 1. When resistance is connected between the pin 31 (28, 25) and GND, I 5. Switch (pin 13) can be changed by supplying some voltage as figure 2. 0 to 0.5 V: INPUT1 2.5 to 5 V: INPUT2...
- Page 18 M61323SP/FP Cautions for Manufacturing Boards Built-in wide band preamplifier may cause oscillation due to the wiring shape on the board. Be careful for the following points. • V shall use a stable power supply. (Individual V should use an independent power supply.) •...
-
Page 19: Package Dimensions
M61323SP/FP Package Dimensions JEITA Package Code RENESAS Code P-SDIP32-8.9x28-1.78 PRDP0032BA-A SEATING PLANE JEITA Package Code RENESAS Code P-SSOP36-8.4x15-0.80 PRSP0036GA-B REJ03F0201-0201 Rev.2.01 Mar 31, 2008 Page 19 of 19 Previous Code MASS[Typ.] 32P4B 2.2g Previous Code MASS[Typ.] 36P2R-D 0.5g Index mark NOTE) 1. - Page 20 (4) any other purposes that pose a direct threat to human life Renesas shall have no liability for damages arising out of the uses set forth in the above and purchasers who elect to use Renesas products in any of the foregoing applications shall indemnify and hold harmless Renesas Technology Corp., its affiliated companies and their officers, directors, and employees against any and all...