Danfoss FC 300 Operating Instructions Manual page 74

Specifications
LCP and typical control card power consumptions are included. Further options and customer load may add up to 30W to the losses.
(Though typical only 4W extra for a fully loaded control card, or options for slot A or slot B, each).
Although measurements are made with state of the art equipment, some measurement inaccuracy must be allowed for (
5) The three values for the max. cable cross section are for single core, flexible wire and flexible wire with sleeve, respectively.
Typical Shaft Output [kW]
Enclosure IP20, IP21
Enclosure IP55
Output current
Continuous (3x525-550 V) [A]
Intermittent (3x525-550 V) [A]
Continuous (3x551-600 V) [A]
Intermittent (3x551-600 V) [A]
Continuous kVA (525 V AC) [kVA]
Continuous kVA (575 V AC) [kVA]
Max. input current
Continuous (3x525-600 V) [A]
Intermittent (3x525-600 V) [A]
Additional specifications
IP20, IP21 max. cable cross section
motor, brake and load sharing) [mm
IP55, IP66 max. cable cross section
motor, brake and load sharing) [mm
Max. cable cross section
Estimated power loss
at rated max. load [W]
10 10
Weight, Enclosure IP20 [kg]
Weight, enclosure IP55 [kg]
Efficiency 4)
Table 10.7 Mains Supply 3x525-600 V AC (FC 302 only)
70
VLT ® AutomationDrive Operating
Instructions
PK75
0.75
A3
A5
1.8
2.9
1.7
2.7
1.7
1.7
1.7
2.7
5)
(mains,
2 (AWG)] 2)
5) (mains,
2
(AWG)]
5)
with disconnect
35
4)
6.5
13.5
0.97
MG33AM02 - VLT
P1K1 P1K5 P2K2
1.1 1.5 2.2
A3 A3 A3
A5 A5 A5
2.6 2.9 4.1
4.2 4.6 6.6
2.4 2.7 3.9
3.8 4.3 6.2
2.5 2.8 3.9
2.4 2.7 3.9
2.4 2.7 4.1
3.8 4.3 6.6
4,4,4 (12,12,12)
(min. 0.2 (24))
4,4,4 (12,12,12)
6,4,4 (10,12,12)
50 65 92
6.5 6.5 6.5
13.5 13.5 13.5
0.97 0.97 0.97
®
is a registered Danfoss trademark
± 5%).
P3K0 P4K0 P5K5
3 4 5.5
A3 A3 A3
A5 A5 A5
5.2 6.4 9.5
8.3 10.2 15.2
4.9 6.1 9.0
7.8 9.8 14.4
5.0 6.1 9.0
4.9 6.1 9.0
5.2 5.8 8.6
8.3 9.3 13.8
122 145 195
6.5 6.5 6.6
13.5 13.5 14.2
0.97 0.97 0.97
P7K5
7.5
A3
A5
11.5
18.4
11.0
17.6
11.0
11.0
10.4
16.6
261
6.6
14.2
0.97