emmeti CS-11 User Manual

CS-11 LCD 7-Day 5+2 Programmable Digital Thermostat
Buttons and LCD display
Buttons
Short press
Turning on/off thermostat
Auto/Manual mode selection
M
Set the time and week days
Confirm settings
Increase the set value
Decrease the set value
+ Lock /unlock buttons
M
+
Turning ON/OFF Your Thermostat
Press buttton to turn the thermostat ON or OFF. When thermostat is turned off, LCD will display OFF.

Configuration Menu

This thermostat is full of useful features which can be set quite easily through the feature configuration menu. To access the feature configuration menu, simply turn off your thermostat
and hold button M for 5 seconds. Now you can see Menu 1, to proeceed to other menu, press button M again. To exit menu, press button
Feature Description
Menu #
Sensor selection. This thermostat is a combination model allowing you to choose
between 4 different models. (A, AF,F )
1
A model: air onl y, with built in sensor
AF model: air & floo r , with both built in and remote sensor
F model: floor only, with remote sensor
Switching differential.
set temperature and on again to reach the set temperature.The default is 1°C which
means the thermostat will switch the heating on 0.5°C below the set temperature and
2
will turn it off 0.5°C above the set temperature. With a 2°C differential, the heating will switch
on 1°C below the set temperature and switch off 1°C above the set temperature.
Calibrate the room temperature. This feature is used to compensate for any difference
3
between the displayed room temperature and a thermometer.
Calibrate the floor temperature. This feature is used to compensate for any difference
4
between the displayed floor temperature and a thermometer.
Pump protection(for hydronic heating only). In hydronic heating installations, it is
recommended to activate the pump at least 15 seconds every 24 hours in order to
5
avoid any seizing. Select ON to activate this feature, OFF to deactivate. When the
thermostat is activating the pump, the
6
Optimum start(preheat). This feature is to ensure that the required temperature has
already been reached when you get up in the morning or come home from work.
Set the floor temperature limit.
7
Set backlight turning-on time. Selecting on will turn the light on continuously.
8
Selecting off will turn the light off. Selecting 20 seconds will turn the light on for 20 seconds.
Select temperature format
9
10
Select 12 / 24 hour clock
11
Frost protection.
Program type selection. This gives user 3 options of program type.
12
5_2 will give you 5 days(Monday to Fiday) with the same six events(Wakeup, out, home,
out, home,sleep) and 2 days(Saturday and Sunday) with the same six events.
6_1 will give you 6 days(Monday to Saturday) with the same six events(Wakeup, out, home,
out,home,sleep) and 1 day(Sunday) with the same six events.
7_0 will give you individual settings for each day from Monday to Sunday.
Error
E0 = The internal sensor has developed a fault. You should contact your thermostat retailer for assistance.
Message
E1 = The remote floor sensor has not been connected, has been wired incorrectly or the probe is faulty.
LO = The room or floor temperature is below 0
HI = The room or floor temperature is above 50 °C
This product should be installed by a qualified electrician.
Press > 5 seconds
Menu button( when thermostat is turned off)
Program button( when thermostat is turned on)
Cancel override( when in override mode)
Bring up vacation mode
Check floor temperature (AF model only)
Reset to factory settings
(when thermostat is turned off)
The number of degrees difference between switching off at the
icon will blink.
This feature is to protect the floor surface.
°C or °F.
This feature is to avoid room temperature going below 5 °C
°C
See overleaf for further setting up information
Registered Address: 6 Tannery Yard, Witney Street, Burford, Oxon., OX18 4DW
Tel: 01993 824900 : www.emmeti.co.uk : e: sales@emmeti.co.uk
U9310044
Symbol
AUTO
Temporary
SET AT
Program 1,2,
3,4,5,6
Description
Auto mode(use button M to select)
Manual mode(use button M to select)
Vacation mode
Temporary temperature override
Frost protection activated
Set temperature
The program number
The buttons are locked.
Displays when heating is active
Factory Default
Press
Feature Value
A A / AF / F
1°C
0°C
0°C
OFF
OFF
40 °C
20 seconds / ON /OFF
20 seconds
°C
24
OFF
5_2 / 6_1 / 7_0
7_0
or to select
1°C ~ 5°C
-5°C ~ +5°C
-5°C ~ +5°C
ON / OFF
ON / OFF
20°C ~ 40 °C
°C / °F
12 / 24
ON / OFF