Introduction/Box Contents - Sonance DSP 2-750 MKII Instruction Manual

Introduction
Thank you for purchasing the Sonance Sonamp DSP 2-750 MKII
amplifier. When properly installed, this amplifier will give you many
years of entertainment pleasure. To get the most out of your new
Sonance DSP2-750 MKII Amplifier
amplifier, please read this manual thoroughly before you
begin installation.
Rear Panel 4/ 2/ 2018
To achieve the best performance, Sonance recommends that this
Die Line Do N ot Print
amplifier be installed by a Sonance Authorized Dealer/Installer.
Prints W hite
Box Contents
(1) Instruction manual
(1) Network connection instructions
(1) Sonamp DSP 2-750 MKII amplifier
(1) IEC power cord
(4) Removable rubber feet
(2) Long rack ears
1-L 1-R
IN
OUT
Sonance DSP2-750 MKII Amplifier
Rear Panel 4/ 2/ 2018
Die Line Do N ot Print
Prints W hite
1-L 1-R 2-L
IN
OUT
2-L 2-R
IN
OUT
2-R
IN
OUT
Figure 1: Sonamp DSP 2-750 MKII Multi-Channel Power Amplifier
Unpacking
Save the carton and polystyrene inserts for future safe transport in
case the amplifier is moved or requires shipping for repair.
Before proceeding with installation, locate the serial number on the
rear panel of the unit and note it here for future reference:
S/N:_____________________________________________________.
Placement
Place the amplifier on a level surface, in an upright position, out
of direct sunlight and away from windows through which rain
may enter. Situate the amplifier away from heat sources such as
hot air ducts or radiators. Be sure that the amplifier is adequately
ventilated by convection or suitable cabinet fans.
• Never place any object on or against the amplifier.
• Never operate the amplifier on a carpeted surface as this will
compromise ventilation.
• When the amplifier is installed in any cabinet, the front or back
must be open during operation. Alternately, install fans in the
cabinet to assure continuous ventilation.
_
+
+
BRIDGE
4 Ω MIN
1L 1R
DSP 2-750 MKII
_
+
+
BRIDGE
4 Ω MIN
1L 1R
DSP 2-750 MKII
3
IR IR
CONTROL STATUS
IN
REPLACE FUSE ONLY WITH SAME
REMPLACER UNIQUEMENT AVEC
LE MEME TYPE ET CALIBRE DU
VOLTAGE TRIGGER
IN OUT
OUT
_ _ _
+ + +
TCP/IP
_ DEFAULT IP
3-30 volts AC/DC
192.168.1.50
RISQUE DE CHOC ELECTRIQUE
IR IR
CONTROL STATUS
T10AL/250VAC
IN
REPLACE FUSE ONLY WITH SAME
TYPE AND RATING OF FUSE
REMPLACER UNIQUEMENT AVEC
LE MEME TYPE ET CALIBRE DU
VOLTAGE TRIGGER
IN OUT
OUT
_ _ _
+ + +
TCP/IP
_ DEFAULT IP
3-30 volts AC/DC 192.168.1.50
DSP 2-750 MKII
S/N
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
T10AL/250VAC
CAUTION
TYPE AND RATING OF FUSE
AC 100-120V ~ 60Hz
ATTENTION
AC 220-240V ~ 50Hz
FUSIBLE
DSP 2-750 MKII
S/N
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS
NE PAS OUVRIR
CAUTION
AC 100-120V ~ 60Hz
ATTENTION
AC 220-240V ~ 50Hz
FUSIBLE