Table of Contents
Advertisement
Quick Links
14-700
7" Wet Tile Saw
Operator's Manual
Record the serial number and date of purchase in your manual for future reference.
Serial Number: _________________________
Date of purchase: _________________________
For technical support or parts questions, email techsupport@rikontools.com or call toll free at (877)884-5167
www.rikontools.com
14-700M1
Advertisement
Table of Contents
Related Manuals for Rikon Power Tools 14-700
Summary of Contents for Rikon Power Tools 14-700
- Page 1 14-700 7” Wet Tile Saw Operator’s Manual Record the serial number and date of purchase in your manual for future reference. Serial Number: _________________________ Date of purchase: _________________________ For technical support or parts questions, email techsupport@rikontools.com or call toll free at (877)884-5167 www.rikontools.com...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Specifications........................2 Safety Instructions ......................3 - 6/ 7&12 Getting To Know Your Tile Saw ....................7 Contents of Package .....................8 Assembly ......................... 9 - 12 Operation ........................12 - 18 Maintenance ........................18 Troubleshooting ......................19 Electricals & Wiring Diagram ..................5 & 19 Parts Diagram &... -
Page 3: Safety Instructions
SAFETY INSTRUCTIONS IMPORTANT! Safety is the single most important consideration in the operation of this equipment. The following instructions must be followed at all times. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury. There are certain applications for which this tool was designed. - Page 4 SAFETY INSTRUCTIONS 12. KEEP PROTECTIVE GUARDS IN PLACE AND IN 25. ALWAYS WEAR A DUST MASK TO PREVENT WORKING ORDER. INHALING DANGEROUS DUST OR AIRBORNE PARTICLES, including wood dust, crystalline silica dust 13. AVOID ACCIDENTAL STARTING. Make sure that and asbestos dust. Direct particles away from face and the power switch is in the “OFF”...
-
Page 5: Electricals & Wiring Diagram
SAFETY INSTRUCTIONS ELECTRICAL SAFETY EXTENSION CORDS THIS TOOL IS PRE-WIRED FOR 120V THE USE OF AN EXTENSION CORD WITH THIS MACHINE IS NOT RECOMMENDED. For CIRCUITS, AND MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM ELECTRIC SHOCK. best power and safety, plug the machine directly into a dedicated, grounded electrical outlet that is within the IN THE EVENT OF A MALFUNCTION OR BREAKDOWN,... -
Page 6: Save These Instructions
SAFETY INSTRUCTIONS SPECIFIC SAFETY INSTRUCTIONS FOR TILE SAWS This machine is intended for the cutting of man-made tile, pavers and stone tile products only. The permissible workpiece dimensions must be observed (see Technical Specification). Any other use not as specified, including modification of the machine or use of parts not tested and approved by the equipment manufacturer, can cause unforeseen damage and invalidate the warranty. -
Page 7: Getting To Know Your Tile Saw
GETTING TO KNOW YOUR WET TILE SAW Rip Fence Splash Hood Water Reservoir Miter Guide Overflow Drain Maximum Water Fill Line Switch 7” Blade Rip Fence Bevel Table Cord Storage Carrying Handle Wrench Storage NOTE: This saw is designed to cut man-made tile, pavers, and stone tile products only. TO REDUCE THE RISK OF INJURY, DO NOT USE TILE SAW BLADES LARGER OR SMALLER THAN 7”... -
Page 8: Contents Of Package
CONTENTS OF PACKAGE Model 14-700 7” Wet Tile Saw is shipped complete in one box. Unpacking, Checking Contents & Clean-up 1. Carefully remove all contents from the shipping carton. Compare the contents with the list of contents to make sure that all of the items are accounted for, before discarding any packing material. Place parts on a protected surface for easy identification and assembly. -
Page 9: Assembly
ASSEMBLY THE MACHINE MUST NOT BE PLUGGED IN AND THE POWER SWITCH MUST BE IN THE OFF POSITION UNTIL ASSEMBLY IS COMPLETE. BLADE INSTALLATION 1. Lift and remove the Bevel Table. SEE Figure 1. FIGURE 1 2. Remove the Arbor Nut (A-Fig. 2) and Outer Flange (B-Fig. - Page 10 ASSEMBLY THE MACHINE MUST NOT BE Splash Hood PLUGGED IN AND THE POWER SWITCH MUST BE IN Bracket THE OFF POSITION UNTIL ASSEMBLY IS COMPLETE. INSTALLING THE SPLASH HOOD Flat Head 1. Slide the Splash Hood Bracket into the lip Screws under the Table behind the Blade.
- Page 11 ASSEMBLY THE MACHINE MUST NOT BE PLUGGED IN AND THE POWER SWITCH MUST BE IN THE OFF POSITION UNTIL ASSEMBLY IS COMPLETE. MITER GUIDE INSTALLATION 1. The Miter Guide is attached to the Rip Fence by a sliding dovetail system. Align the male dovetail under the Miter Guide with the dovetail groove in the top of the Rip Fence.
-
Page 12: Operation
ASSEMBLY THE MACHINE MUST NOT BE PLUGGED IN AND THE POWER SWITCH MUST BE IN THE OFF POSITION UNTIL ASSEMBLY IS COMPLETE. REPLACING THE BEVEL TABLE 1. Hold the Bevel Table at an extreme angle above the main table. SEE Figure 10. Lower the left side of the Bevel Table and engage the three hinge pins under the main table. - Page 13 OPERATION TO REDUCE THE RISK OF ELECTROCUTION, KEEP ALL CONNECTIONS DRY AND OFF THE GROUND. DO NOT TOUCH THE PLUG OR CORD WITH WET HANDS. To avoid the possibility of the tool plug or outlet getting wet, position tile saw to one side of a wall- mounted outlet to prevent water from dripping onto the outlet or plug.
- Page 14 OPERATION TO REDUCE THE RISK OF ELECTROCUTION, KEEP ALL CONNECTIONS DRY AND OFF THE GROUND. DO NOT TOUCH THE PLUG OR CORD WITH WET HANDS. CROSS CUTTING CROSS CUTTING Continued from page 13. 5. Make sure the material is clear of the blade before turning on the saw.
- Page 15 OPERATION TO REDUCE THE RISK OF ELECTROCUTION, KEEP ALL CONNECTIONS DRY AND OFF THE GROUND. DO NOT TOUCH THE PLUG OR CORD WITH WET HANDS. 45° DIAGONAL CUT 45° DIAGONAL CUT Continued from page 14. 7. Turn the on/off switch to the ON position. 8.
- Page 16 OPERATION TO REDUCE THE RISK OF ELECTROCUTION, KEEP ALL CONNECTIONS DRY AND OFF THE GROUND. DO NOT TOUCH THE PLUG OR CORD WITH WET HANDS. MAKING A MITER CUT MAKING A MITER CUT Continued from page 15. 7. Turn the on/off switch to the ON position. 8.
- Page 17 OPERATION TO REDUCE THE RISK OF ELECTROCUTION, KEEP ALL CONNECTIONS DRY AND OFF THE GROUND. DO NOT TOUCH THE PLUG OR CORD WITH WET HANDS. MAKING AN “L” CUT MAKING AN “L” CUT Continued from page 16. 8. Let the blade build up to full speed and wait for the blade to get wet before moving the mate- rial into the blade.
-
Page 18: Maintenance
OPERATION TO REDUCE THE RISK OF ELECTROCUTION, KEEP ALL CONNECTIONS DRY AND OFF THE GROUND. DO NOT TOUCH THE PLUG OR CORD WITH WET HANDS. BEVEL CUTTING BEVEL CUTTING Continued from page 17. NOTE: Make sure bevel table is held firmly in place on the two pins, for the degree angle of choice, on each leg before beginning cut. -
Page 19: Troubleshooting
TROUBLESHOOTING SYMPTOM POSSIBLE CAUSES SOLUTIONS Saw will not start 1. Power cord is not plugged in 1. Plug in saw to power source 2. Fuse or circuit board tripped 2. Replace fuse or reset breaker 3. Damaged power cord 3. Contact Technical Support by calling 4. -
Page 20: Parts Diagram & Parts Lists
PARTS DIAGRAM... - Page 21 PARTS LIST DESCRIPTION KEY NO. PART NO. P14-700-1 6-10x25mm Hex Head Bolt P14-700-2 Splash Hood P14-700-3 Knob P14-700-4 5-0.8x16mm Flat Head Screw P14-700-5 Splash Hood Bracket P14-700-6 Rubber Pin P14-700-7 Table P14-700-8 Bevel Table P14-700-9 4-0.7mm Lock Nut P14-700-10 4mm Flat Washer P14-700-11 Bevel Table Leg P14-700-12...
- Page 22 PARTS LIST KEY NO. DESCRIPTION PART NO. P14-700-46 Thread Forming Screw P14-700-47 O-ring P14-700-48 6-1.0x20mm Pan Head Screw P14-700-49 Lifting Handle P14-700-50 6mm Flat Washer P14-700-51 6mm Lock Nut P14-700-52 Inner Flage P14-700-53 Cutting Wheel P14-700-54 Outer Flage P14-700-55 Arbor Nut P14-700-56 P14-700-57 Overflow Drain...
-
Page 23: Warranty
® 2-Year Limited Warranty RIKON Power Tools Inc. (“Seller”) warrants to only the original retail consumer/purchaser of our products that each product be free from defects in materials and workmanship for a period of two (2) years from the date the product was purchased at retail. This warranty may not be transferred. - Page 24 14-700 For more information: 16 Progress Road Billerica, MA 01821 877-884-5167 / 978-528-5380 techsupport@rikontools.com www.rikontools.com 14-700M1...