Eaton LINX Installation Manual
  1. Manuals
  2. Brands
  3. Eaton Manuals
  4. Indoor Furnishing
  5. LINX
  6. Installation manual
Eaton LINX Installation Manual

Eaton LINX Installation Manual

Modular furniture
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Modular Furniture
LINX
™
Modular Furniture
Installation manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LINX and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Eaton LINX

Summary of Contents for Eaton LINX

  • Page 1 Modular Furniture LINX ™ Modular Furniture Installation manual...
  • Page 2 CONTENTS OF THIS DOCUMENT SHALL NOT BECOME PART OF OR MODIFY ANY CONTRACT BETWEEN THE PARTIES. In no event will Eaton be responsible to the purchaser or user in contract, in tort (including negligence), strict liability or otherwise for any special, indirect, incidental or consequential damage or loss whatsoever, including but not limited to damage or...

  • Page 3: Table Of Contents

    Binder Shelf ....................................A26 Cable Management..................................A27 Nova Kit Assembly..................................A29 Semi Recessed Monitor ................................A35 Adjustable CPU Holder, Nova ..............................A38 LINX Worksurface Service Parts List ............................A39 HEIGHT ADJUSTABLE WORKSURFACE ASSEMBLY ......................B Universally Adjustable ..................................B1 Single Surface Adjustable................................B2 Height Adjustable Worksurface Service Parts List ........................B4 MOBILE PEDESTAL ................................C1...
  • Page 4 L i n e a r W o r k s u r f a c e s technical furniture TYPICAL LEG AND MODESTY PANEL ASSEMBLY Tools Required -1/4” Hex key (provided) -Phillips head screwdriver NOTE: Due to packaging restrictions, the foot is not factory assembled to the 40”...
  • Page 5 L i n e a r W o r k s u r f a c e s technical furniture Standard leg Glide feet TYPICAL WORKSURFACE ASSEMBLY assemblies 1. Remove the Worksurface from the carton and place it carefully, finish side down, on a smooth clean surface. 2.

  • Page 6: Jetty

    J e t t y W o r k s u r f a c e technical furniture Tools Required -5/32” Hex key (provided) -1/4” Hex key (provided) -Phillips head screwdriver NOTE: The Jetty Worksurfaces are available as Right and Left hand units. 1.
  • Page 7 C o r n e r W o r k s t a t i o n ( F r e e S t a n d i n g ) technical furniture Tools Required -5/32” Hex key (provided) -1/4” Hex key (provided) -Phillips head screwdriver 1.

  • Page 8: Deluxe Integrated

    D e l u x e I n t e g r a t e d technical furniture W o r k s u r f a c e Tools Required -5/32” Hex key (provided) -1/4” Hex key (provided) -Phillips head screwdriver 1.
  • Page 9 B u l l e t C o n f e r e n c e technical furniture W o r k s u r f a c e Tools Required -Phillips head screwdriver 1. Remove the Worksurface from the carton and place it carefully, finish side down, on a smooth clean surface.

  • Page 10: Linear Conference

    L i n e a r C o n f e r e n c e technical furniture W o r k s u r f a c e Tools Required -Phillips head screwdriver 1. Remove the Worksurface from the carton and place it carefully, finish side down, on a smooth clean surface.
  • Page 11 Top Support and Tie Plate (provided) be installed to link the surfaces and provide sup- port. Top support 1. Assemble a Top Support to the leg of one of the Linx 1/4”-20 x 3/4” Phillips workstations using two 1/4”-20 x 3/4” Phillips pan Linx workstation pan head machine screws head machine screws.
  • Page 12 S q u a r e / R e c t a n g u l a r C o n n e c t technical furniture w i t h Tools Required -5/32” Hex Key (provided) -1/4” Hex Key (provided) -Phillips head screwdriver 1.
  • Page 13 S q u a r e / R e c t a n g u l a r C o n n e c t technical furniture w i t h M o d e s t y P a n e l s 3.
  • Page 14 S q u a r e / R e c t a n g u l a r C o n n e c t technical furniture w i t h C o r n e r Tools Required -5/32” Hex key (provided) -1/4”...
  • Page 15 S q u a r e / R e c t a n g u l a r C o n n e c t technical furniture w i t h C o r n e r S u p p o r t 4.

  • Page 16: Square/Rectangular Connectors

    S q u a r e / R e c t a n g u l a r C o n n e c t technical furniture w i t h C o r n e r S u p p o r t Square/Rectangular Connector With Corner Support 69735...

  • Page 17: Triangular Connector

    T r i a n g u l a r technical furniture C o n n e c t o r Tools Required -Electric drill -1/8” Dia. drill bit -5/32” Allen wrench Triangular Connector NOTE: Two people are required for some steps in the Hole plug installation procedure.
  • Page 18 T r i a n g u l a r technical furniture C o n n e c t o r ( c o n t . ) Top support 4. Align the two workstations in their approximate final Extended 1/4”-20 x 1/2” positions.

  • Page 19: Curved Connector

    1/4”-20 x 3/8” Button head cap screws provided. Hole plugs See Figure 1. Top support 3. Position the Two Linx workstations in their required (R.H. shown) positions for the Corner Connector being installed. Next, place the Corner Connector on top of the Top Supports.
  • Page 20 C u r v e d C o r n e r C o n n e c t o r technical furniture M o d e s t y P a n e l s Corner Connector 84253...

  • Page 21: Conference End

    Tools Required - Phillips head screw driver - Level 1. Align and level the two LINX workstations to which the Conference End is to be installed. See Figure 1. 2. Remove the two top hole plugs from each leg.
  • Page 22 -5/32” Hex key (provided) -1/4” Hex key (provided) -Phillips head screwdriver Peninsula, Bolt-On 1. Position the two Linx Workstations to which the Bolt-on Peninsula is to be attached approximately 30” apart. See Figure 1. 30” 2. Remove the top two plastic hole plugs from one leg of each workstation.
  • Page 23 P e n i n s u l a , B o l t - o n technical furniture ( c o n t . ) 3. The Modesty Panel is installed from the rear and 12”/26” Modesty fits between the Top Supports and the Legs. Fasten panel it with four 1/4”-20 x 3/4”...
  • Page 24 P e n i n s u l a , B o l t - o n technical furniture Bolt-on Peninsula 84913...
  • Page 25 1/4”-20 x 3/4” Phillips head screws. 4. Remove the top two plastic hole plugs from the adjoining LINX workstation and install the remain- ing Top Support using one 1/4”-20 x 3/4” Phillips head screw. Do not fully tighten at this time. See Figure 1 Figure 3.
  • Page 26 Leg/Modesty panel 5. Attach the Leg/Modesty Panel assembly to the ad- joining LINX workstation. The Modesty panel in- stalls from the rear and fits between the Top Support and the leg. Attach it with two 1/4”-20 x 3/4” Phil- lips head screws.
  • Page 27 P e n i n s u l a , T o p technical furniture C o n n e c t i o n Tools Required -Phillips head screwdriver -Electric drill -1/8” Drill bit NOTE: The Peninsula is provided with the Top Con- nection Bracket/Stiffener and the die cast Leg Mounting Plate factory installed.
  • Page 28 C o n f e r e n c e T a b l e technical furniture Tools Required -Phillips head screwdriver -5/32” Allen wrench (provided) 1. Using the 1/4”-20 x 2.00” button head cap screws and lock washers provided, assemble the base. The Leg Connector has tapped holes.
  • Page 29 C o n f e r e n c e T a b l e ( c o n t . ) technical furniture 2. Remove the Conference Table Top from the carton and place it carefully, finished side down, on a smooth clean surface.

  • Page 30: Round Conference

    C o n f e r e n c e T a b l e ( c o n t . ) technical furniture Parts List Part Number Description Qty. 2176X Round Conference Table Top, 36” 2177X Round Conference Table Top, 42” 2178X Round Conference Table Top, 48”...

  • Page 31: Posting Shelf

    P o s t i n g S h e l f technical furniture Tools Required -Powered Drill (with #33 drill bit) -Phillips Screw Driver SELECTING A LOCATION Positioning the Posting Shelf to the extreme left or right C855MM is recommended for all Workstations. Posting Shelf On 24”...

  • Page 32: Storage Shelf

    S t o r a g e S h e l f technical furniture Tools Required -5/32” Hex key -Phillips head screwdriver Storage Shelf Rear phillips head screw 1. Remove the two lower plastic Hole Plugs located on the inside of each leg. See Figure 1. Workstation 2.

  • Page 33: Binder Shelf

    B i n d e r S h e l f technical furniture Tools Required -5/32” Allen wrench (provided) -Phillips head screwdriver Binder Shelf Rear phillips head screw 1.Remove the two lower plastic Hole Plugs located on Hole plug the inside of each leg and replace them with the two (remove) 1/4”- 20 x 3/8”...

  • Page 34: Cable Management

    Tools Required - None Removable Wire covers Cable management is an intergral element of each Linx Workstation. * 2” x 2” Cable Ports in laminate tops Modesty panel w/cable management * Modesty Panels with “stepped” design for horizontal cable runs.
  • Page 35 W o r k s t a t i o n C a b l e technical furniture M a n a g e m e n t ( c o n t . ) WIRE COVERS Pre-punched access holes The Wire Covers are attached to the rear of each work- station leg and vertically route cables from the Modesty Panel down the rear of the leg.
  • Page 36 N o v a Please read these instructions carefully and follow the installation steps in sequence. NOTE: The Trim Ring provided with the Nova01 and Nova06 kits can not be used with Linx Worksurfaces. Please discard Trim Ring. Tools required -Phillips head screwdriver...
  • Page 37 4. Attach the Tracks to the to the underside of the Worksurface by aligning the holes in the Tracks with the corresponding holes in the Worksurface (or stiffener on a 30” Linx Worksurface) and securing #14AB x 3/4” with the #6AB x 5/8” screws provided. Note: One end...
  • Page 38 R e t r o f i t K i t N o v a ( c o n t . ) technical furniture 6. Attach the Palm Rest to the front of the keyboard drawer using the pre-drilled holes and three #8AB x Keyboard drawer 1/2”...
  • Page 39 R e t r o f i t K i t N o v a ( c o n t . ) technical furniture MONITOR SUPPORT INSTALLATION NOTE: The Monitor Support adjusts three ways - for 3. To make angle adjustments, move either the top height, angle and forward/backward.
  • Page 40 R e t r o f i t K i t N o v a ( c o n t . ) technical furniture Parts List Part Number Description Qty. 1 5001818-02 Side Assembly 2 5001818-03 Cross Brace Keyboard Drawer 4 5001818-06 Monitor Support 5 5001818-07 Viewport Glass 6 5001818-08 Leveler...
  • Page 41 R e t r o f i t K i t N o v a ( c o n t . ) technical furniture A-34 86270...

  • Page 42: Semi Recessed Monitor

    #10AB x 3/8” phillips head thread forming screws. See figure 1. Frame NOTE: Linx worksurfaces are shipped with the frame factory installed. If the frame is being installed into a Worksurface front...
  • Page 43 S e m i R e c e s s e d technical furniture M o n i t o r ( c o n t . ) 2. Install the Monitor Shelf by hooking the front and Install the #10-24 x 3/8” screws with spacers into the rear tabs into the desired slot location on the Frame.
  • Page 44 S e m i R e c e s s e d technical furniture M o n i t o r ( c o n t . ) Parts List Part Number Description Qty. 8867X Frame, Standard Monitor 8868X Frame, Large Monitor 8869X Shelf, Standard Monitor 8870X...

  • Page 45: Adjustable Cpu Holder, Nova

    A d j u s t a b l e C P U technical furniture H o l d e r , N o v a Please read these instructions carefully and follow the installation steps in sequence. Tools Required -None 1.
  • Page 46 L I N X W o r k s u r f a c e S e r v i c e P a r t s L i s t technical furniture Parts List Parts List Part Number Description Qty.
  • Page 47 L I N X W o r k s u r f a c e S e r v i c e P a r t s L i s t technical furniture ( c o n t . ) Parts List Parts List Part Number...
  • Page 48 L I N X W o r k s u r f a c e S e r v i c e P a r t s L i s t technical furniture ( c o n t . ) Parts List Parts List Part Number...
  • Page 49 L I N X W o r k s u r f a c e S e r v i c e P a r t s L i s t technical furniture ( c o n t . ) Parts List Parts List Part Number...
  • Page 50 W o r k s u r f a c e s / C o n f e r e n c e W o r k - technical furniture s u r f a c e s Linx Worksurfaces Conference Worksurfaces 84567 A-43...
  • Page 51 T r i a n g u l a r C o n n e c t o r technical furniture Triangular Connector A-44 84571...
  • Page 52 S q u a r e / R e c t a n g u l a r C o n n e c t technical furniture w i t h M o d e s t y P a n e l s Square/Rectangular Connector With Modesty Panels Square/Rectangular Connector...
  • Page 53 C o n f e r e n c e E n d technical furniture Conference End 84252/85217 A-46...
  • Page 54 L i n k e d P e n i n s u l a / B o l t - O n P e n i n s u l a technical furniture Linked Peninsula Bolt-on Peninsula 84569/84913 A-47...
  • Page 55 T o p C o n n e c t i o n P e n i n s u l a C u r v e d technical furniture C o r n e r C o n n e c t o r Top Connection Peninsula Curved Corner Connector 80752/84253...
  • Page 56 C o n f e r e n c e T a b l e technical furniture A-49 81071-B...
  • Page 57 P o s t i n g S h e l f technical furniture Posting Shelf 84085 A-50...
  • Page 58 S t o r a g e S h e l f technical furniture Storage Shelf A-51 81046...
  • Page 59 W o r k s t a t i o n C a b l e technical furniture M a n a g e m e n t ( c o n t . ) Cable Management Components 84566 A-52...

  • Page 60: Universally Adjustable

    U n i v e r s a l l y A d j u s t a b l e V D T technical furniture S t a n d Tools Required - 4mm Allen wrench (provided) -5mm Allen wrench (provided) -6mm Allen Wrench (provided) -Phillips head screwdriver Universally Adjustable VDT Stand...
  • Page 61 W o r k s u r f a c e S i d e technical furniture E x t e n s i o n Tools Required -5mm Allen wrench (provided) -Phillips head screw driver Parts List (1) #5377X - Top (1) #2519X - Support (1) #59103 - #10AB x 3/4”...
  • Page 62 W o r k s u r f a c e S i d e technical furniture E x t e n s i o n ( c o n t . ) Parts List Part Number Description Qty. 5377X 2519X Support Side Extension 59103...
  • Page 63 H e i g h t A d j u s t a b l e W o r k s u r f a c e technical furniture Tools Required -Phillips head screwdriver -6mm Allen wrench (provided) Height Adjustable Worksurface Base frame 1.
  • Page 64 H e i g h t A d j u s t a b l e W o r k s u r f a c e ( c o n t . ) technical furniture 3. The Front Crank Assembly may be installed on either the right or left side.
  • Page 65 H e i g h t A d j u s t a b l e S e r v i c e P a r t s L i s t technical furniture Parts List Part Number Description Qty. 1934X/1933X Base Frame 82741 Top Support, L.H.
  • Page 66 H e i g h t A d j u s t a b l e W o r k s u r f a c e s technical furniture Height Ajustable Worksurface Universally Adjustable VDT Stand 82743...

  • Page 67: Mobile Pedestal

    M o b i l e P e d e s t a l technical furniture Tools Required -None CASTER INSTALLATION 1. Carefully lay the Mobile Pedestal on its back. Install Mobile Pedestal a Caster at each corner of the bottom by inserting the #C843, #C845, #C846 Caster stems into the holes .
  • Page 68 W o r k s t a t i o n technical furniture O r g a n i z e r s Tools Required -Phillips head screwdriver -5/32” Allen wrench (provided) -Electric drill -1/8” Drill bit -Drill template (provided) IMPORTANT: It is recommended that the assembly of this product be done on the floor.
  • Page 69 1. Using the cardboard Drill Template provided, drill two 1/8” diameter holes approximately 1/2” deep into the Perforations two corners of the Linx Corner Workstation as shown Figure 1. Carefully fold the template along perforations and place the template on the corner of the worksurface as shown in Figure 2.
  • Page 70 FASTENING THE ORGANIZER TO NON-WRIGHT LINE MANUFACTURED WORKSURFACES If the worksurface to which the Organizer is to be in- stalled is not a Wright Line LINX worksurface, locate and drill the four 1/8” diameter x 1/2” deep holes in the rear corners as indicated below.

  • Page 71: Locking Compartment

    L o c k i n g C o m p a r t m e n t s technical furniture Tools Required -Phillips head screwdriver -5/32” Allen wrench Caution: The Workstation Organizer must be secure- ly attached to a Worksurface before proceeding with the installation of any component.
  • Page 72 L o c k i n g C o m p a r t m e n t s technical furniture ( c o n t . ) END PANEL INSTALLATION (cont.) FULL LENGTH SHELF End panel, R.H. 1. A Full Length Shelf may be positioned at any of three levels as shown in Figure 3b.
  • Page 73 L o c k i n g C o m p a r t m e n t s technical furniture ( c o n t . ) Rear bracket CENTER PANEL INSTALLATION Factory installed (66” and 72” Locking Compartment) screws Back panel The Locking Compartments for the 66”...
  • Page 74 L o c k i n g C o m p a r t m e n t s technical furniture ( c o n t . ) Receding door TOP PANEL INSTALLATION mounting holes (72” Locking Compartment) Top panel 1.
  • Page 75 L o c k i n g C o m p a r t m e n t s technical furniture ( c o n t . ) #10 Phillips head screws (back out 1/16”) TASK LIGHT INSTALLATION 24” TASK LIGHT Shelf stiffener The 24”...
  • Page 76 L o c k i n g C o m p a r t m e n t s technical furniture ( c o n t . ) #10 Phillips head screws (back out 1/16”) 48” TASK LIGHT The 48” Task Light can only be installed in the center Shelf stiffener position.
  • Page 77 L o c k i n g C o m p a r t m e n t s technical furniture ( c o n t . ) Parts List Parts List Part Number Description Qty. Part Number Description Qty. 8191X Receeding Door Assembly, 24”...
  • Page 78 L o c k i n g C o m p a r t m e n t s technical furniture ( c o n t . ) 80954LX D-11...

  • Page 79: Pass Through Organizer

    P a s s - T h r o u g h technical furniture O r g a n i z e r s Tools Required -Phillips head screwdriver -5/32” Allen wrench (provided) -Electric drill -1/8” Drill bit -Drill template (provided) IMPORTANT: It is recommended that the assembly of this product be done on the floor.
  • Page 80 1. Using the cardboard Drill Template provided, drill two 1/8” diameter holes approximately 1/2” deep into the Perforations two corners of the Linx Worksurface as shown in Figure 2. Carefully fold the template along perforations and place the template on the corner of the worksurface as shown in Figure 2.
  • Page 81 1. Using the cardboard Drill Template provided, drill two 1/8” diameter holes approximately 1/2” deep into the two corners of the Linx Corner Workstation as shown Figure 1. Carefully fold the template along perforations and place the template on the corner of the worksurface as shown in Figure 2.
  • Page 82 C o r n e r W o r k s t a t i o n technical furniture O r g a n i z e r ( c o n t . ) 2. Install Mounting Brackets at each corner of the work- surface with the #10 x 3/4”...
  • Page 83 C o r n e r W o r k s t a t i o n technical furniture O r g a n i z e r ( c o n t . ) Arrow label “Install this side up” Upright 4.

  • Page 84: Corner Shelf

    C o r n e r L a m i n a t e technical furniture S h e l f Tools Required -5/32” Allen wrench (provided) -Phillips head screw driver -Electric drill* -1/8” Dia. drill bit* * Required for the installation of the WD06-XX, 42”(1067mm) x 42”(1067mm) Shelf only.
  • Page 85 C o r n e r L a m i n a t e technical furniture S h e l f ( c o n t . ) 1. Determine the Corner Shelf height and remove two 1/4”-20 Button head cap screws from each Upright at the desired height.
  • Page 86 C o r n e r L a m i n a t e technical furniture S h e l f ( c o n t . ) Rear support “A” 3. Install one Rear Support “A” and one Rear Support 6”...
  • Page 87 C o r n e r L a m i n a t e technical furniture S h e l f ( c o n t . ) Parts List Part Number Description Qty. 2287X Shelf Side Bracket 2288X Rear Shelf Support “A” 2289X Rear Shelf Support “B”...

  • Page 88: Reception Surface

    R e c e p t i o n S u r f a c e technical furniture Tools Required -5/32” Allen wrench (provided) -Phillips head screwdriver 1. Using the 5/32” Allen wrench, remove the two 1/4”-20 x .50” Button head cap screws from the top inner surface of the uprights of each organizer receiving a Reception Surface.
  • Page 89 R e c e p t i o n S u r f a c e technical furniture ( c o n t . ) Parts List Part Number Description Qty. 4608X Support 59103 #10AB x .75” Phillips Head Screw 5411X Reception Counter, 15”...

  • Page 90: Overhead Shelf

    O r g a n i z e r O v e r h e a d technical furniture S h e l f Tools Required -5/32” Allen wrench (provided) -7/16” Wrench -Plastic mallet NOTE: The Shelf is shipped with four shoulder screws installed in the bottom surface.
  • Page 91 O r g a n i z e r O v e r h e a d technical furniture S h e l f ( c o n t . ) 4. Four 3/4” squares of double faced adhesive tape have been provided to attach the bottom edge of the Shelf Rear panel Rear Panel to the top of the Organizer back panel.
  • Page 92 O r g a n i z e r O v e r h e a d technical furniture S h e l f ( c o n t . ) Parts List Parts List Part Number Description Qty. Part Number Description Qty.

  • Page 93: Fabric Back Panel

    -None Tackable Fabric Back Panels Magnetic strips Fabric back panel NOTE: The LINX Organizer must be fastened to the Worksurface. 1. The Tackable Fabric Back Panel has magnetic strips which allows it to be installed on the back of a LINX Organizer. Position the panel on the back of the organizer and adjust it vertically or horizontally as necessary.
  • Page 94 T a c k a b l e F a b r i c technical furniture B a c k P a n e l s ( c o n t . ) Parts List Part Number Description Qty. W206-XX 16”H x 24”W Rear Fabric Panel W306-XX 16”H x 30”W Rear Fabric Panel W366-XX 16”H x 36”W Rear Fabric Panel W436-XX 16”H x 42”W Rear Fabric Panel...
  • Page 95 W o r k s t a t i o n O r g a n i z e r s S e r v i c e technical furniture P a r t s L i s t Parts List Parts List Part Number Description...
  • Page 96 W o r k s t a t i o n O r g a n i z e r s S e r v i c e technical furniture P a r t s L i s t ( c o n t . ) Parts List Parts List Part Number...
  • Page 97 W o r k s t a t i o n O r g a n i z e r s S e r v i c e technical furniture P a r t s L i s t ( c o n t . ) 36”...
  • Page 98 W o r k s t a t i o n O r g a n i z e r s S e r v i c e technical furniture P a r t s L i s t ( c o n t . ) 16”...
  • Page 99 W o r k s t a t i o n O r g a n i z e r s S e r v i c e technical furniture P a r t s L i s t ( c o n t . ) 32”...
  • Page 100 W o r k s t a t i o n O r g a n i z e r s S e r v i c e technical furniture P a r t s L i s t ( c o n t . ) 36”...
  • Page 101 1. Position the TechOrganizer in the desired location on the back of the Worksurface. On a Linx Worksur- #10AB x 2.25” Phillips face, locate the back of the frame .20” from the back flat head screws edge of the Worksurface.
  • Page 102 T e c h O r g a n i z e r S e r v i c e P a r t s L i s t technical furniture Parts List Parts List Part Number Description Qty. Part Number Description Qty.
  • Page 103 T e c h O r g a n i z e r S e r v i c e P a r t s L i s t technical furniture ( c o n t . ) Parts List Part Number Description Qty.
  • Page 104 T e c h O r g a n i z e r S e r v i c e P a r t s L i s t technical furniture ( c o n t . ) Parts List Part Number Description Qty.
  • Page 105 T e c h O r g a n i z e r S e r v i c e P a r t s L i s t technical furniture ( c o n t . ) Parts List Part Number Description Qty.

  • Page 106: Corner Tech Organizer

    Important Safety Instructions * The Organizer must be properly secured to the Work- surface prior to installing of components. * Frame load capacity is 300 lbs. (Linx worksurfaces) 400 lbs. (Workbenches). * Do not install shelves that are greater than 18” deep.
  • Page 107 2. With two people, position the TechOrganizer in the flat head screws desired location on the back of the Worksurface. On a Linx Worksurface, locate the back of the frame .20” Corner TechOrganizer from the back edge of the Worksurface. See Figure 2.
  • Page 108 W h i t e , P e g A n d technical furniture B i n B o a r d s Tools Required -Phillips head screwdriver -Flat blade screwdriver -Plastic mallet NOTE: White Boards, Peg Boards and Bin Boards are provided in various widths and heights depending on the size of your TechOrganizer.
  • Page 109 W h i t e , P e g A n d B i n B o a r d s technical furniture ( c o n t . ) 2. Attach the Board panel to the Mounting IMPORTANT Channels by inserting the panel hooks into the The panel must be fully seated prior to installation rectangular slots in the Mounting Channels.
  • Page 110 W h i t e , P e g A n d B i n B o a r d s technical furniture ( c o n t . ) Parts List Part Number Description Qty. 85100 White Board - 11.64” High x 20.92” Wide 85101 White Board - 11.64”...
  • Page 111 W h i t e , P e g A n d B i n B o a r d s technical furniture ( c o n t . ) Parts List Part Number Description Qty. 6197X Peg Board - 31.64” High x 32.92” Wide 6198X Peg Board - 43.64”...
  • Page 112 W h i t e , P e g A n d B i n B o a r d s technical furniture ( c o n t . ) E-12 85089...
  • Page 113 M a r k e r T r a y technical furniture Tools Required -None Marker Tray 1. Remove the release liner from the double faced tape on the back of the Marker Tray. 2. Carefully align the bottom of the Tray with the White board bend line at the bottom of the White Board and center it side to side.
  • Page 114 M a r k e r T r a y ( c o n t . ) technical furniture Parts List Part Number Description Qty. 6596X Marker Tray - 24” 6597X Marker Tray - 30” 6598X Marker Tray - 36” E-14 85130...
  • Page 115 F a b r i c T e c h W a l l technical furniture Tools Required -Phillips head screwdriver -Flat file NOTE: Panels are provided in various widths and heights depending on the size of your unit. IMPORTANT For ease of installation, it is recommended that the Fabric Tech Walls be installed onto theTechOrganizer frame prior to the installation of other components.
  • Page 116 F a b r i c T e c h W a l l ( c o n t . ) technical furniture Important: For proper Tech Wall installation, the Mounting Channels must attach flat against the slotted standards. If a weld joining the two halves Double standard of the double standard exceeds a height of approxi- mately .03”(.8mm), it may be necessary to carefully...
  • Page 117 F a b r i c T e c h W a l l ( c o n t . ) technical furniture Tech Wall Installation with Components Pre-installed on One Side of the Frame Tech Walls may be installed onto the Organizer frames that have other components on one side.
  • Page 118 F a b r i c T e c h W a l l ( c o n t . ) technical furniture Parts List Parts List Part Number Description Qty. Part Number Description Qty. 6213X 12.52” x 21.21” Fabric Panel 6350X 12.52”...
  • Page 119 F a b r i c T e c h W a l l ( c o n t . ) technical furniture E-19 85082...
  • Page 120 C o r n e r L a m i n a t e H o o k - O n S h e l v e s technical furniture Tools Required -Plastic mallet -Phillips head screwdriver Corner Laminate Hook-on Shelves TechOrganizer 1.
  • Page 121 C o r n e r L a m i n a t e H o o k - O n S h e l v e s technical furniture ( c o n t . ) Parts List Part Number Description Qty.
  • Page 122 C o r n e r L a m i n a t e H o o k - O n S h e l v e s technical furniture ( c o n t . ) 85093 E-22...
  • Page 123 LINX Installation Manual Eaton is a registered trademark. Eaton 1000 Eaton Boulevard * All trademarks are property Cleveland, OH 44122 of their respective owners. United States Eaton.com Eaton 160 Gold Star Boulevard Follow us on social media to get the ©...

Table of Contents