Related Manuals for Eaton Linear Tech Bench 1
Summary of Contents for Eaton Linear Tech Bench 1
- Page 1 Sit-to-Stand Techbench Sit-to-Stand Techbench installation manual Linear Tech Bench 1 Corner Tech Bench 1...
-
Page 2: Table Of Contents
CONTENTS OF THIS DOCUMENT SHALL NOT BECOME PART OF OR MODIFY ANY CONTRACT BETWEEN THE PARTIES� In no event will Eaton be responsible to the purchaser or user in contract, in tort (including negligence), strict liability or other- wise for any special, indirect, incidental or consequential damage or loss whatsoever, including but not limited to damage or... -
Page 3: Before You Begin
Sit-to-Stand Techbench SECTION I Installation Manual Before you begin Before installing the Eaton's Sit-to-stand bench, it is recommended that you do the following: • Read and understand the instruction herein before attempting to • The use of personal protective equipment such as safety unpack, assemble, operate or service the Sit-to-stand bench�... -
Page 4: Bench Capacity
LOWERED� are not limited to) monitor poles, electronic equipment, power distribution units, and cabling� DO NOT PLACE ANY OBJECT ON TOP OF THE BENCH’S SUPPORT BASE THAT COULD INTERFERE WITH THE TRAVEL OF THE WORKSURFACE� SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench... -
Page 5: The Bench Components
" driver bit • " open end box wrench • #2 Phillips bit • #3 Phillips bit • Level • 4mm Hex wrench (provided in hardware kit) • " combination wrench Sit-to-Stand Corner and Linear Techbench Components SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench... -
Page 6: Assembly Hardware
Reference Letter Letter 1/4" x ½" hex head self- Wire clip (qty� 3) threading screw Eaton part # 105970 Eaton part # 54538 M6 x 14mm Allen -20 x 3/4 hex head head screws machine screw Eaton part # 105948... -
Page 7: A� Wiring The Bench - Ac Cord
Route cord thru cut out in work surface stiffener Hardware required AC Cord relief clip and screw K & L x 1 Lift motor controller #10 x 1 screw J x 2 Rear of work surface SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench... -
Page 8: B� Wiring The Bench - Control Pad
Control pad wire Slot in work surface stiffener Bottom slot in work surface stiffener Lift motor controller receptacle Wire clip retainer Control touch #8 x " flat head hardware H x 2 Front work surface pull slot SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench... -
Page 9: C� Wiring The Bench - Motor Cables
Wire stay #1 motor plug #1 motor plug #4 motor plug #3 motor plug #2 motor plug #2 motor plug #2 motor plug #4 motor #4 motor plug Cable retainer cable bundle SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench... -
Page 10: D� Wiring The Leg Assembly
- before back panel attachment Connect #2 motor cable Connect #1 motor cable Motor assembly in work surface stiffener - before back panel attachment Connect #4 Connect #3 motor cable motor cable SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench... -
Page 11: E� Leg Assembly And Back Panel
• Hand thread remaining (2) 1/4-20 hex head screws in back panel� Do not tighten Back panel mounting holes Back panel -20 x 3/4 hex head machine screw M x 6 Back panel mounting holes SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench... -
Page 12: F � Leg Assembly
- slot 6mm id nylon washer hardware D M6 shoulder screw hardware C Work surface Work surface stiffener stiffener - hole M6 x 14mm Allen screw hardware B 6mm id steel washer hardware E Lift motor SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench... -
Page 13: G� Initialize The Lift Motor System
This is because the system can be in different modes when the initialization starts� 5� After initialization, press the up button to lift the work surface (in this case the frame)� SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench... -
Page 14: A� Adjusting The Levelers
Press and hold one of the memory buttons and the system will start driving to the pre-programmed memory position� The adjustment can only be done via the DPF configurator� Keep the button pushed until the position is reached� SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench... -
Page 15: A� Full Shelf Installation
USE CAUTION WHEN LIFTING WORK SURFACE. TWO PEOPLE ARE REQUIRED TO AVOID INJURY. Foot Mounting holes in foot 1/4-20 x 1/2" hex head self tap screws. Hardware A (8X) Cut out to Full shelf the rear SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench... -
Page 16: B� Half Shelf Installation
Foot mounting hex head mounting holes hole machine screw Half shelf " id steel -20 x " lg hex head washer self-tap screw Left side shelf bracket -20 x " lg hex head self-tap screw SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench... -
Page 17: C� Caster And Foot Rest Installation
To install foot rest use (4) 1/4-20x½" lg hex head self-tap CASTER INSTALLATION. screws as shown Hardware required M x 4 Mounting holes in foot Foot rest Caster -20 x " lg hex -20 x " lg hex head head self-tap screw self-tap screw SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench... -
Page 18: D� Cable Chain Installation
Cable chain #10-32x1" lg. Phillips pan head screw Hardware K (2) 10-32x " lg. Phillips pan head screw Hardware P (2) Chain bracket 10-32x " lg. Phillips pan head screw Hardware P (2) SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench... -
Page 19: E� Flextray
• Each flextray bracket requires one flextray retainer assembly� Flextray Back panel bracket mounting holes " hex head self-tap screw Crimping tab on flextray bracket -20 carriage bolt Flextray retainer -20 kepnut Flextray Back panel SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench... -
Page 20: F � Ganging Plate
Rear mounting hole -20x lg. hex head self-tap screw Ganging plate Right hand foot of bench -20x lg. hex head self-tap screw Left hand foot of bench Front Mounting slot mounting in ganging plate hole SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench... -
Page 21: User Maintenance Instructions
Excessive scrubbing PARTS. ALL SERVICING EXCEPT CLEANING AND PERIODIC or exerting too much force could damage the decorative VISUAL INSPECTION SHALL BE PERFORMED BY AN EATON surface� AUTHORIZED SERVICE REPRESENTATIVE. Recommended cleaners for work surfaces THIS BENCH’S ELECTRICAL LIFT SYSTEM HAS DOUBLE-...
Need help?
Do you have a question about the Linear Tech Bench 1 and is the answer not in the manual?
Questions and answers