Page 2
, ORNAND , Easy DesignSim , Traveo combinations thereof, are trademarks and registered trademarks of Cypress Semiconductor Corp. ARM and Cortex are the registered trademarks of ARM Limited in the EU and other countries. Purchase of I C components from Cypress or one of its sublicensed Associated Companies conveys a license under the...
Page 3
All information included in this document is current as of the date it is issued. Such information is subject to change without any prior notice. Please confirm the latest relevant information with the sales representatives. S6SAE100A00VA1001 Evaluation Board Operation Guide, Doc No. 002-08728 Rev.*A...
Page 4
Because the product has no casing, it is recommended that it be stored in the original Damage packaging. Transporting the product may cause a damage or fault. Therefore, keep the packaging materials and use them when re-shipping the product. S6SAE100A00VA1001 Evaluation Board Operation Guide, Doc No. 002-08728 Rev.*A...
Description The S6SAE100A00VA1001 is the tiny evaluation board for the ultra-low-power energy harvesting PMIC for indoor type solar cell, S6AE100A series. This evaluation board consists of three independent boards for S6SAE101A, S6SAE102A and S6SAE103A. This board is capable of supporting life extension of primary battery or becoming battery-less solution, and it is for evaluation of diverse power management functions used for wireless sensor network.
Please refer the S6AE102A and S6AE103A datasheet (002-08501) for more information. Board size: 19 mm × 11 mm for S6AE101A, 20.5 mm × 16 mm for S6AE102A, 23 mm × 16 mm for S6AE103A. S6SAE100A00VA1001 Evaluation Board Operation Guide, Doc No. 002-08728 Rev.*A...
Shorted between CIN2 pin and GND Short SW21 Shorted ENA_LDO2 pin to VINT2 pin or GND Short ENA_LDO2-VINT2(H) SW22 Shorted STBY_LDO2 pin to VINT2 or GND Short STBY_LDO2-GND(L) Figure 3-4 Jumper/Switch Layout S6SAE100A00VA1001 Evaluation Board Operation Guide, Doc No. 002-08728 Rev.*A...
Page 12
Short STBY_LDO3-GND(L) Short SW33 Shorted ENA_COMP3 pin to VINT3 pin or GND ENA_COMP3-GND(L) Short COMPM3-VINT3(H) SW34 Shorted COMPM3 pin or COMPP3 pin to VINT3 pin Short COMPP3-VINT3(H) Figure 3-5 Jumper/Switch Layout S6SAE100A00VA1001 Evaluation Board Operation Guide, Doc No. 002-08728 Rev.*A...
Rx4, Rx5 = (R24, R25 / R34, R35) Initial setting value of output voltage of the board is VOUT_LDOx2.55V To change output voltage, derive Rx4 and Rx5 values by using following calculation formulas VOUT_LDOx 1.15×(Rx4+Rx5) VOUT_LDOx = S6SAE100A00VA1001 Evaluation Board Operation Guide, Doc No. 002-08728 Rev.*A...
3. To change the output voltage setting, change the resistor value of R11, R12 and R13 with referring section 3.3 Output Voltage Setting. Figure 4-1 Connection of Indoor Type Solar Cell (S6AE101A) Multimeter VSTORE1_1 Solar Cell Multimeter VOUT1_1 VDD1 S6SAE100A00VA1001 Evaluation Board Operation Guide, Doc No. 002-08728 Rev.*A...
Page 15
5. To change the output voltage setting of LDO, change the resistor value of R24 and R25 with referring section 3.3 Output Voltage Setting. Figure 4-2 Connection of Indoor Type Solar Cell (S6AE102A) Solar Cell VDD2 Multimeter VOUT_LDO2 Multimeter VOUT2_2 Multimeter VOUT1_2 Multimeter VSTORE1_2 S6SAE100A00VA1001 Evaluation Board Operation Guide, Doc No. 002-08728 Rev.*A...
Page 16
5. To change the output voltage setting of LDO, change the resistor value of R34 and R35 with referring section 3.3 Output Voltage Setting. Figure 4-3 Connection of Indoor Type Solar Cell (S6AE103A) Solar Cell VDD3 Multimeter VOUT_LDO3 Multimeter VOUT2_3 Multimeter VOUT1_3 Multimeter VSTORE1_3 S6SAE100A00VA1001 Evaluation Board Operation Guide, Doc No. 002-08728 Rev.*A...
4. To change the output voltage setting, change the resistor value of R11, R12 and R13 with referring section 3.3 Output Voltage Setting. Figure 4-4 Hybrid Connection of Indoor Type Solar Cell and Primary Battery with Board (S6AE101A) VBAT1 Multimeter VSTORE1_1 Solar Cell Multimeter/ Electric load VOUT1_1 VDD1 S6SAE100A00VA1001 Evaluation Board Operation Guide, Doc No. 002-08728 Rev.*A...
Page 18
Voltage Setting. Figure 4-5 Hybrid Connection of Indoor Type Solar Cell and Primary Battery with Board (S6AE102A) Solar Cell VDD2 Multimeter VOUT_LDO2 Multimeter VOUT2_2 VBAT2 Multimeter/ Electric load VOUT1_2 Multimeter VSTORE1_2 S6SAE100A00VA1001 Evaluation Board Operation Guide, Doc No. 002-08728 Rev.*A...
Page 19
Voltage Setting. Figure 4-6 Hybrid Connection of Indoor Type Solar Cell and Primary Battery with Board (S6AE103A) Solar Cell VDD3 Multimeter VOUT_LDO3 Multimeter VOUT2_3 VBAT3 Multimeter/ Electric load VOUT1_3 Multimeter VSTORE1_3 S6SAE100A00VA1001 Evaluation Board Operation Guide, Doc No. 002-08728 Rev.*A...
CN12, CN13, CN23, CN24, CN25, CN33, 2.54 mm 2pin non mount CN34, CN35 CN26 2.54 mm 1pin non mount These components are compliant with RoHS, but ask each vender for details if necessary. S6SAE100A00VA1001 Evaluation Board Operation Guide, Doc No. 002-08728 Rev.*A...
Board Splitting The PCB can be cut along the V-cut line. The torsional stress on the board is reduced, when a force is applied to the entire V-cut line. Figure 9-1 Board S6SAE100A00VA1001 Evaluation Board Operation Guide, Doc No. 002-08728 Rev.*A...
Revision History Document Revision History Document Title: S6SAE100A00VA1001 Energy Harvesting PMIC S6AE10xA Evaluation Board Operation Guide Document Number: 002-08728 Revision ECN No. Origin of Description of Change Change TAOA New Specification 5131017 ATTS Table2-1 Description of output voltage is changed...
Need help?
Do you have a question about the S6SAE100A00VA1001 and is the answer not in the manual?
Questions and answers