Cigar Lighter Relay - Jeep XJ Manual

XJ
REMOVAL AND INSTALLATION (Continued)
INSTRUMENT PANEL ACCESSORY SWITCH
BEZEL
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, REFER TO
RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY
STEERING WHEEL,
INSTRUMENT PANEL COMPONENT DIAGNOSIS OR
SERVICE. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
BAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the center bezel from the instrument
panel. Refer to Instrument Panel Center Bezel in
the Removal and Installation section of this group for
the procedures.
(3) Remove the three screws that secure the acces-
sory switch bezel to the instrument panel (Fig. 8).
Fig. 8 Instrument Panel Accessory Switch Bezel
Remove/Install
(4) Pull the accessory switch bezel away from the
instrument panel far enough to access the instru-
ment panel wire harness connectors.
(5) Disconnect the instrument panel wire harness
connectors from the connector receptacles, the acces-
sory switches, the cigar lighter and the accessory
power outlet on the back of the accessory switch
bezel.
(6) Remove the accessory switch bezel from the
instrument panel.
INSTALLATION
(1) Position the accessory switch bezel to the
instrument panel.
(2) Reconnect the instrument panel wire harness
connectors to the connector receptacles, the accessory
GROUP 8M - PASSIVE
STEERING COLUMN,
INSTRUMENT PANEL SYSTEMS
switches, the cigar lighter and the accessory power
outlet on the back of the accessory switch bezel.
(3) Position the accessory switch bezel onto the
instrument panel.
(4) Install and tighten the three screws that secure
the accessory switch bezel to the instrument panel.
Tighten the screws to 2.2 N·m (20 in. lbs.).
OR
(5) Install the center bezel onto the instrument
panel. Refer to Instrument Panel Center Bezel in
the Removal and Installation section of this group for
the procedures.
(6) Reconnect the battery negative cable.

CIGAR LIGHTER RELAY

WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, REFER
RESTRAINT SYSTEMS BEFORE ATTEMPTING ANY
STEERING WHEEL,
INSTRUMENT PANEL COMPONENT DIAGNOSIS OR
SERVICE. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
BAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
REMOVAL
(1) Disconnect and isolate the battery negative cable.
(2) Remove the fuse access panel by unsnapping it
from the right cowl side trim panel.
(3) Remove the stamped nut that secures the right
cowl side trim to the junction block stud (Fig. 9).
(4) Remove the screw located above the fuse access
opening that secures the right cowl side trim to the
right cowl side inner panel.
(5) Remove the screw that secures the right door
sill trim and the right cowl side trim to the right
door opening sill.
(6) Remove the right cowl side trim panel from the
vehicle.
(7) Refer to Junction Block in the Contents of
Group 8W - Wiring Diagrams for cigar lighter relay
identification and location.
(8) Remove the cigar lighter relay from the recep-
tacle in the junction block.
INSTALLATION
(1) Refer to Junction Block in the Contents of
Group 8W - Wiring Diagrams for the proper cigar
lighter relay location.
(2) Position the cigar lighter relay to the receptacle
in the junction block.
(3) Align the terminals of the cigar lighter relay
with the cavities in the junction block receptacle.
(4) Push on the cigar lighter relay case firmly and
evenly until all of the relay terminals are fully seated
within the cavities of the junction block receptacle.
TO GROUP 8M -
STEERING COLUMN,
8E - 15
PASSIVE
OR