Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Norac Case AFS Pro 600
Summary of Contents for Norac Case AFS Pro 600
- Page 1 Spray Height Controller Case AFS Pro 600 Display Kit Installation Manual PRO600...
- Page 2 Reorder P/N: 54VT-PRO600-INST Rev B (Case AFS PRO 600 Display Kit) NOTICE: NORAC Systems International Inc. reserves the right to improve products and their specifications without notice and without the requirement to update products sold previously. Every effort has been made to ensure the accuracy of the information...
-
Page 3: Table Of Contents
Contents 1 INTRODUCTION ..................... 2 1.1 VT Software Version..............................2 1.2 List of Parts ................................. 2 2 INSTALLATION ....................3 2.1 Self Propel ................................... 3 2.2 Switch Box Installation ............................. 4 3 CABLE DRAWINGS ..................5 3.1 ITEM C01: 43220-01 - CABLE UC5 NETWORK 14 AWG - 1M ..............5 3.2 ITEM C30: 43250-14 –... -
Page 4: Introduction
1 Introduction The Case AFS Pro 600 Display Kit Manual is intended to be used in conjunction with the UC5 Spray Height Control Installation Manual. This manual provides instructions to interface the UC5 Control Module to the Case AFS Pro 600 Display. For installation of the rest of the UC5 Spray Height Control System please refer to the sprayer specific manual provided with the kit. -
Page 5: Installation
Connect the 2 pin DT connector on C30 to a 15A, +12 VDC source. 5. Connect cable C01 to the other CANbus connector and route the cable to the Valve Module. Figure 1: Case AFS Pro 600 Display Kit – Self Propelled Sprayer... -
Page 6: Switch Box Installation
Switch Box Installation 1. Disconnect cable C20 (grey side connector) from the Input Module (E03). Remove the wedge from the face of the 12 pin Deutsch plug. 2. Insert the Roll CW pin from C26 into position 3 of the 12 pin plug on C20. Insert the Roll CCW pin from C26 into position 4 of the 12 pin plug on C20. -
Page 7: Cable Drawings
3 Cable Drawings ITEM C01: 43220-01 - CABLE UC5 NETWORK 14 AWG - 1M ITEM C30: 43250-14 – CABLE UC5 BATTERY 2 PIN DT... -
Page 8: Item C25: 44602-01 - Switch Remote Hand Control
ITEM C25: 44602-01 – SWITCH REMOTE HAND CONTROL... -
Page 9: Item C26: 43240-26 - Cable Uc5 Switch Box
ITEM C26: 43240-26 – CABLE UC5 SWITCH BOX... -
Page 10: Item C40: 43260-07 - Cable Uc5 Can Bus 3 Pin Dt J1939
ITEM C40: 43260-07 – CABLE UC5 CAN BUS 3 PIN DT J1939... -
Page 11: Appendix A: Alternate Configuration
Appendix A: Alternate Configuration If your sprayer has European style slant control, you will need to reconfigure the switch box as shown below. This is only required for sprayer types which are driving the slant output from the Input Module. Reconfigure the pins on cable C26 as follows: Normal Configuration European Style Slant Configuration Function... - Page 12 Canada NORAC Systems International Inc. Phone: (+1) 306 664 6711 Toll Free: 1 800 667 3921 Shipping Address: 3702 Kinnear Place Saskatoon, SK S7P 0A6 United States NORAC, Inc. Phone: (+1) 952 224 4142 Toll Free: 1 866 306 6722...
Need help?
Do you have a question about the Case AFS Pro 600 and is the answer not in the manual?
Questions and answers