Subscribe to Our Youtube Channel
Related Manuals for Norac Case AFS Pro 300
Summary of Contents for Norac Case AFS Pro 300
- Page 1 Case AFS Pro 300, 600, 700 Display Kit (20 & 30 Series - Self-Propelled) Installation Manual 54VT-PRO-SP01...
- Page 2 Copyright 2017 by NORAC Systems International Inc. Reorder P/N: 54VT-PRO-SP01-INST Rev G (Case AFS PRO 300, 600, 700 (20 & 30 Series - Self-Propelled Display Kit) NOTICE: NORAC Systems International Inc. reserves the right to improve products and their specifications without notice and without the requirement to update products sold previously.
-
Page 3: Table Of Contents
Contents INTRODUCTION ...................... 2 VT Software Version................................2 List of Parts ..................................2 INSTALLATION ......................3 CANbus Interface Installation ............................3 Switch Box Installation ..............................5 CABLE DRAWINGS ....................6 ITEM C25: 50250 - Switchbox ............................6 ... -
Page 4: Introduction
VT Software Version Before you connect the UC5 to the Case AFS Pro 300, 600 or 700, you must ensure that you have the latest VT software installed. The VT software must be Version 25 or newer. -
Page 5: Installation
2 Installation CANbus Interface Installation 1. Securely mount the control module (E01) on the center boom at the rear of the sprayer. 2. Tee the CANbus interface cable (C40) in to the Case “Application” CANbus. “Application” CANbus is either a 3-pin Deutsch connector or a 4-pin Deutsch connector. It is located on the center section of the boom at the rear of the sprayer. - Page 6 Figure 2: CANbus Interface Installation with Cable C42...
-
Page 7: Switch Box Installation
Switch Box Installation 1. Disconnect cable C20 (Thru 2 connector) from the input module (E03). Remove the wedge from the face of the 12-pin Deutsch plug. 2. Insert the Roll CW pin from C26 into position 3 of the 12-pin plug on C20. Insert the Roll CCW pin from C26 into position 4 of the 12-pin plug on C20. -
Page 8: Cable Drawings
3 Cable Drawings ITEM C25: 50250 - Switchbox... -
Page 9: Item C26: 43240-47 - Cable Uc5 Interface Switch Box - 50250
ITEM C26: 43240-47 – Cable UC5 Interface Switch Box - 50250... -
Page 10: Item C30: 43250-14 - Cable Uc5 Battery 2 Pin Dt Tee Fused (Ecu & Sig)
ITEM C30: 43250-14 – Cable UC5 Battery 2 Pin DT Tee Fused (ECU & SIG) -
Page 11: Item C40: 43260-07 - Cable Canbus 3 Pin Dt J1939
ITEM C40: 43260-07 – Cable CANbus 3 Pin DT J1939... -
Page 12: Item C41: 43220-01 - Cable Network 14 Awg - 1M
ITEM C41: 43220-01 - Cable Network 14 AWG - 1M... -
Page 13: Item C42: 43260-29 - Cable Interface Dt 4 Pin 12 In Stub
ITEM C42: 43260-29 – Cable Interface DT 4 Pin 12 IN Stub... -
Page 14: Appendix A: Alternate Configuration
Appendix A: Alternate Configuration If your sprayer has European style slant control, you will need to reconfigure the switch box as shown below. This is only required for sprayer types which are driving the slant output from the Input Module. Reconfigure the pins on cable C26 as follows: Normal Configuration European Style Slant Configuration Function... - Page 15 TOPCON Agriculture Canada 3702 Kinnear Place Saskatoon, SK S7P 0A6 TOPCON Agriculture Americas W5527 Hwy 106 Fort Atkinson, WI 53538 TOPCON Precision Agriculture Europe Avenida de la industria, 35, Tres Cantos, España Spain Support Phone: 888 979 9509 E-mail: tasupportn@topcon.com Web: www.norac.ca...
Need help?
Do you have a question about the Case AFS Pro 300 and is the answer not in the manual?
Questions and answers