Carrier 30RB060-390 Installation Instructions Manual page 65

UNIT VOLTAGE
30RB
Supplied
UNIT
V-Hz
SIZE
(3 Ph)
Min Max
208/230-60 187 253 168.8/141.5
380-60 342 418 86.4/ 74.1
060
460-60 414 506 73.6/ 62.5
575-60 518 633 59.0/ 50.0
208/230-60 187 253 212.0/141.5
380-60 342 418 110.9/ 74.1
070
460-60 414 506 93.6/ 62.5
575-60 518 633 76.3/ 50.0
208/230-60 187 253 216.5/168.8
380-60 342 418 112.5/ 86.4
080
460-60 414 506 95.2/ 73.6
575-60 518 633 76.2/ 59.0
208/230-60 187 253 283.6/168.8
380-60 342 418 150.1/ 86.4
090
460-60 414 506 126.0/ 73.6
575-60 518 633 102.2/ 59.0
208/230-60 187 253 283.6/212.0
380-60 342 418 150.1/110.9
100
460-60 414 506 126.0/ 93.6
575-60 518 633 102.2/ 76.3
208/230-60 187 253 283.6/243.8
380-60 342 418 150.1/124.8
110
460-60 414 506 126.0/106.3
575-60 518 633 102.2/ 85.2
208/230-60 187 253 295.5/306.2
380-60 342 418 156.7/160.2
120
460-60 414 506 131.4/135.2
575-60 518 633 106.5/110.2
208/230-60 187 253 401.7/243.8
380-60 342 418 212.5/124.8
130
460-60 414 506 178.4/106.3
575-60 518 633 144.7/ 85.2
208/230-60 187 253 401.7/306.2
380-60 342 418 212.5/160.2
150
460-60 414 506 178.4/135.2
575-60 518 633 144.7/110.2
208/230-60 187 253 519.8/243.8
380-60 342 418 274.9/124.8
160
460-60 414 506 230.8/106.3
575-60 518 633 187.3/ 85.2
208/230-60 187 253 519.8/306.2
380-60 342 418 274.9/160.2
170
460-60 414 506 230.8/135.2
575-60 518 633 187.3/110.2
208/230-60 187 253 543.7/400.4
380-60 342 418 288.0/209.5
190
460-60 414 506 241.6/176.8
575-60 518 633 195.9/144.1
LEGEND
AWG — American Wire Gage
ICF — Instantaneous Current Flow (Ckt1/Ckt2)
MCA — Minimum Circuit Amps (Ckt1/Ckt2)
MOCP — Maximum Overcurrent Protection (Ckt1/Ckt2)
XL — Across-the-Line Start
NOTES:
1. Units are suitable for use on electrical systems where voltage supplied to the unit
terminals is not below or above the listed minimum and maximum limits. Maximum
allowable phase imbalance is: voltage, 2%; amps 10%.
2. Control power is derived from main power. No separate control power connection is
required.
3. Cooler heater is wired into the control circuit so it is always operable as long as the
power supply disconnect is on, even if any safety device is open.
4. For MCA that is less than or equal to 380 amps, 3 conductors are required.
For MCA between 381-760 amps, 6 conductors are required.
For MCA between 761-1140 amps, 9 conductors are required.
For MCA between 1141-1520 amps, 12 conductors are required.
Calculation of conductors required is based on 75 C copper wire.
Table 11A — 30RB060-190 Electrical Data — Dual Point Units
NO HYDRONIC PACKAGE
MCA MOCP ICF
XL XL XL
225/200 560.0/532.8 200/175
110/110 298.4/286.1 100/ 90
100/ 90 247.7/236.6
80/ 70 201.2/192.3
300/200 654.2/532.8 250/175
150/110 364.3/286.1 125/ 90
125/ 90 301.6/236.6 110/ 80
110/ 70 243.9/192.3
250/225 607.8/560.0 250/200
150/110 324.5/298.4 125/100
125/100 269.3/247.7 110/ 90
100/ 80 218.5/201.2
350/225 725.9/560.0 350/200
175/110 403.5/298.4 175/100
150/100 334.0/247.7 150/ 90
125/ 80 269.8/201.2 125/ 70
350/300 725.9/654.2 350/250
175/150 403.5/364.3 175/125
150/125 334.0/301.6 150/110
125/110 269.8/243.9 125/ 90
350/300 725.9/635.0 350/300
175/150 403.5/336.8 175/150
150/125 334.0/280.4 150/125
125/110 269.8/227.4 125/100
350/400 737.8/748.4 350/350
200/200 410.1/413.6 175/175
150/175 339.4/343.2 150/150
125/125 274.1/277.8 125/125
450/300 843.9/635.0 450/300
250/150 465.9/336.8 225/150
200/125 386.4/280.4 200/125
175/110 312.4/227.4 175/100
450/400 843.9/748.4 450/350
250/200 465.9/413.6 225/175
200/175 386.4/343.2 200/150
175/125 312.4/277.8 175/125
600/300 962.0/635.0 600/300
300/150 528.3/336.8 300/150
250/125 438.8/280.4 250/125
200/110 354.9/227.4 200/100
600/400 962.0/748.4 600/350
300/200 528.3/413.6 300/175
250/175 438.8/343.2 250/150
200/125 354.9/277.8 200/125
600/450 985.9/842.6 600/450
300/250 541.3/462.9 300/225
250/200 449.6/384.8 250/200
225/175 363.5/311.7 225/175
3 HP PUMP, 1750 RPM
Rec MCA MOCP ICF
Fuse
XL XL XL
Size
177.9/141.5 250/200 570.8/532.8
91.5/ 74.1 125/110 304.3/286.1
90/ 80 77.8/ 62.5 110/ 90 252.6/236.6
70/ 60 62.3/ 50.0 80/ 70 205.1/192.3
221.1/141.5 300/200 665.0/532.8
116.0/ 74.1 150/110 370.2/286.1
97.8/ 62.5 125/ 90 306.5/236.6
90/ 60 79.6/ 50.0 110/ 70 247.8/192.3
— — —
— — —
— — —
90/ 70 — — —
— — —
— — —
— — —
— — —
— — —
— — —
— — —
— — —
— — —
— — —
— — —
— — —
— — —
— — —
— — —
— — —
— — —
— — —
— — —
— — —
— — —
— — —
— — —
— — —
— — —
— — —
— — —
— — —
— — —
— — —
— — —
— — —
— — —
— — —
— — —
— — —
5. Wiring for main field supply must be rated 75 C minimum. Use copper for all units.
a. Incoming wire size range for the terminal block is no.4 AWG to 500 kcmil.
b. Incoming wire size range of non-fused disconnect with MCA up to 599.9 amps is
3/0 to 500 kcmil.
c. Incoming wire size range of non-fused disconnect with MCA from 600 to
799.9 amps is 1/0 to 500 kcmil.
d. Incoming wire size range of non-fused disconnect with MCA from 800 to
1199.9 amps is 250 kcmil to 500 kcmil.
6. Hydronic pump packages are not available as a factory-installed option for units
30RB210-390.
7. Power draw includes both crankcase heaters and cooler heaters (where used). Each
compressor has a crankcase heater which draws 56 watts of power. Units ordered with
the cooler heater option have 1 (060-150) or 2 (160-300) cooler heaters, 825 watts
each.
65
5 HP PUMP, 1750 RPM
Rec MCA MOCP ICF
Fuse
XL XL
Size
200/175 184.2/141.5 250/200 577.7/532.8
110/ 90 94.5/ 74.1 125/110 308.1/286.1
90/ 80 80.7/ 62.5 110/ 90 255.7/236.6
70/ 60 64.4/ 50.0 90/ 70 207.6/192.3
250/175 227.4/141.5 300/200 671.9/532.8
150/ 90 119.0/ 74.1 150/110 374.0/286.1
110/ 80 100.7/ 62.5 125/ 90 309.6/236.6
90/ 60 81.7/ 50.0 110/ 70 250.3/192.3
— 231.9/168.8 300/225 625.5/560.0
— 120.6/ 86.4 150/110 334.2/298.4
— 102.3/ 73.6 125/100 277.3/247.7
— 81.6/ 59.0 100/ 80 224.9/201.2
— 299.0/168.8 350/225 743.5/560.0
— 158.2/ 86.4 200/110 413.2/298.4
— 133.1/ 73.6 150/100 342.0/247.7
— 107.6/ 59.0 125/ 80 276.2/201.2
— 299.0/212.0 350/300 743.5/654.2
— 158.2/110.9 200/150 413.2/364.3
— 133.1/ 93.6 150/125 342.0/301.6
— 107.6/ 76.3 125/110 276.2/243.9
— 299.0/243.8 350/300 743.5/635.0
— 158.2/124.8 200/150 413.2/336.8
— 133.1/106.3 150/125 342.0/280.4
— 107.6/ 85.2 125/110 276.2/227.4
— 310.9/306.2 400/400 755.5/748.4
— 164.8/160.2 200/200 419.7/413.6
— 138.5/135.2 175/175 347.4/343.2
— 111.9/110.2 125/125 280.5/277.8
— 417.1/243.8 500/300 861.6/635.0
— 220.6/124.8 250/150 475.6/336.8
— 185.5/106.3 225/125 394.4/280.4
— 150.1/ 85.2 175/110 318.8/227.4
— 417.1/306.2 500/400 861.6/748.4
— 220.6/160.2 250/200 475.6/413.6
— 185.5/135.2 225/175 394.4/343.2
— 150.1/110.2 175/125 318.8/277.8
— 535.2/243.8 600/300 979.7/635.0
— 283.0/124.8 300/150 538.0/336.8
— 237.9/106.3 250/125 446.8/280.4
— 192.7/ 85.2 225/110 361.3/227.4
— 535.2/306.2 600/400 979.7/748.4
— 283.0/160.2 300/200 538.0/413.6
— 237.9/135.2 250/175 446.8/343.2
— 192.7/110.2 225/125 361.3/277.8
— 559.1/400.4 600/450 1003.6/842.6
— 296.1/209.5 300/250 551.0/462.9
— 248.7/176.8 250/200 457.6/384.8
— 201.3/144.1 225/175 369.9/311.7
208/230
460
575 v only
Rec
Fuse
XL
Size
225/175
110/ 90
90/ 80
80/ 60
300/175
150/ 90
125/ 80
100/ 60
300/200
150/100
125/ 90
90/ 70
350/200
175/100
150/ 90
125/ 70
350/250
175/125
150/110
125/ 90
350/300
175/150
150/125
125/100
350/350
200/175
150/150
125/125
450/300
250/150
200/125
175/100
450/350
250/175
200/150
175/125
600/300
300/150
250/125
225/100
600/350
300/175
250/150
225/125
600/450
300/225
250/200
225/175