Emerson ControlWave Instruction Manual page 151

ControlWave Instruction Manual (CI-ControlWave)
3-20. Remote DIN-rail mountable
terminal block assembly
assignments for 1-5V AI.......... 3-23
3-21. Local AO module terminal
block assembly assignments .... 3-25
3-22. Remote DIN-rail mountable
terminal block assembly
assignments for AO.................. 3-26
3-23. 4-20mA current loop AO wiring
diagram .................................... 3-27
3-24. UDI module - right side view -
jumper locations....................... 3-30
3-25. UDI (debounce enabled) wiring
diagram .................................... 3-31
3-26. UDI debounce disabled wiring
diagram .................................... 3-31
3-27. Local UDI terminal block
configuration/diagram.............. 3-32
3-28. Remote DIN-rail mountable
terminal block assy. Assignments
for UDI..................................... 3-33
3-29. Selecting Input Type in
ControlWave Designer I/O
Configurator............................. 3-34
3-30. Isolated RTD module wiring
diagram .................................... 3-36
3-31. Local isolated RTD module
terminal block assy. assignments. 3-
37
3-32. Remote DIN-rail mountable
terminal block assy. assignments. 3-
38
3-33. Isolated LLAI Module -
Thermocouple wiring diagram. 3-40
3-34. Local isolated LLAI module
terminal block assy. assignments. 3-
41
3-35. Remote DIN-rail mountable
terminal block assy. assignments. 3-
42
4-1. Power Switch on PSSM.......... 4-1
4-2. Run/Remote/Local Key Switch 4-
2
4-3. Saving a Backup of Your Project
.................................................... 4-5
5-1. HyperTerminal Mode Menu... 5-3
IND-3
5-2. HyperTerminal (Ready to
Download).................................. 5-4
5-3. Send File dialog box ............... 5-4
5-4. HyperTerminal (Download in
progress)..................................... 5-5
5-5 I/O Module to Be Replaced ..... 5-8
5-6. Pulling the I/O Module Out of the
Housing ...................................... 5-9
5-7. I/O Loosening the Top Fastener5-
10
5-8. I/O Terminal Block Board and
Terminal Housing Assembly
Separated from the Rest of the
Module ..................................... 5-10
5-9. New I/O Module in Place Prior to
Attaching Terminal Board and
Terminal Housing Assembly ... 5-11
5-10. Power Supply Sequencer
Module LEDs........................... 5-15
5-11. CPU Module ports and LEDs. 5-
16
5-12. Analog Input (AI) module LEDs
.................................................. 5-16
5-13. Analog output (AO) Module
LEDs ........................................ 5-17
5-14. Digital Input (DI) Module LEDs
.................................................. 5-18
5-15. Digital Output Module LEDs . 5-
19
5-16. Universal Digital Input (UDI)
Module LEDs........................... 5-19
5-17. RTD Module LEDs ............ 5-20
5-18. Low Level Analog Input
Module LEDs........................... 5-21
5-19. NetView.............................. 5-27
5-20. WINDIAG Main Diagnostics
Menu ........................................ 5-27
5-21. RS-232 Loop-back plugs .... 5-29
5-22. RS-485 Loop-back plugs .... 5-29
5-23. Communications Diagnostic
menu......................................... 5-30
5-24. RJ-45 Ethernet Loop-back plug
.................................................. 5-31
5-25. Ethernet Diagnostic Menu .. 5-32
Firmware upgrade .............................. 5-2
HyperTerminal............................... 5-2
Index Revised: Nov-2010