Moxa Technologies EDS-P510 Series Hardware Installation Manual
Etherdevice switch
Hide thumbs
Also See for EDS-P510 Series:
- Quick installation manual (13 pages) ,
- User manual (108 pages) ,
- Manual (84 pages)
Subscribe to Our Youtube Channel
Related Manuals for Moxa Technologies EDS-P510 Series
Summary of Contents for Moxa Technologies EDS-P510 Series
- Page 1 Moxa EtherDevice™ Switch EDS-P510 Series Hardware Installation Guide First Edition, November 2008 © 2008 Moxa Inc. All rights reserved. Reproduction without permission is prohibited. P/N: 1802005101010...
- Page 2 Ethernet equipment can operate in critical industrial environments, such as in hazardous locations, and complies with FCC and CE standards. The installation of the EDS-P510 Series is presented on pages 8 to 14. The installation of the SPL-24 is presented on pages 14 to NOTE...
-
Page 3: Package Checklist
Package Checklist The EDS-P510 is shipped with the following items. If any of these items are missing or damaged, please contact your customer service representative for assistance. 1 EDS-P510 EtherDevice Switch Hardware Installation Guide (this guide) CD-ROM with user’s manual and Windows utility Moxa product warranty statement RJ45 to DB9 console port cable Protective caps for unused ports... - Page 4 WK-46—Wall Mounting Kit (will be shipped with the product) RK-4U—4U-high 19" rack mounting kit Features of EDS-P510 Series High Performance Network Switching Technology IEEE 802.3af Power-over-Ethernet Technology Turbo Ring (recovery time < 20 ms at full load) and RSTP/STP (IEEE802.1w/D)
- Page 5 Operating temperature range from 0 to 60°C, or extended operating temperature from -40 to 75°C for “-T” models IP30, rugged high-strength case DIN-Rail or panel mounting ability Specifications of EDS-P510 Series Technology Standards IEEE 802.3af for Power-over-Ethernet, IEEE 802.3 for 10BaseT, IEEE 802.3u for 100BaseT(X) and 100Base FX,...
- Page 6 Interface RJ45 Ports 10/100BaseT(X) or 10/100/1000BaseT(X) auto negotiation speed Fiber Ports 100/1000BaseSFP slot Console Port RS-232 (RJ45) LED Indicators PWR1, PWR2, FAULT, 10/100M (TP port), 1000M (Gigabit port), MASTER, COUPLER, PoE DIP Switch Turbo Ring, Master, Coupler, Reserve Alarm Contact Two relay outputs with current carrying capacity of 0.5A @ 48 VDC Digital Input...
- Page 7 Traffic Control: NEMA TS2 (Pending) FCC Part 15, CISPR (EN55022) class A EN61000-4-2 (ESD), Level 3 EN61000-4-3 (RS), Level 3 EN61000-4-4 (EFT), Level 2 EN61000-4-5 (Surge), Level 3 EN61000-4-6 (CS), Level 3 EN61000-4-8 EN61000-4-11 Shock IEC60068-2-27 Freefall IEC60068-2-32 Vibration IEC60068-2-6 WARRANTY 5 years —...
- Page 8 Panel Views of EDS-P510 Front Panel View Front Panel 1 to 7: 10/100BaseT(X) port G1 to G3: Combo (10/100/1000BaseT(X) or PWR1 PWR2 FAULT 100/1000BaseSFP slot Gigabit T urbo R ing port.) MASTER COUPLER PWR1: LED for power input 1 10/100/1000 PWR2: LED for power input 2 Fault LED 10/100...
-
Page 9: Mounting Dimensions (Unit = Mm)
Mounting Dimensions (unit = mm) 13.9 51.3 EDS-P510 Side View DIN-Rail Kit Front View 30.5 7.75 7.75 18.2 13.9 13.9 80.2 Rear View Mounting Kit DIN-Rail Mounting The aluminum DIN-Rail attachment plate should already be fixed to the back panel of the EDS-P510 when you take it out of the box. If you need to reattach the DIN-Rail attachment plate to the EDS-P510, make sure the stiff metal spring is situated towards the top, as shown by the following figures. -
Page 10: Wall Mounting (Optional)
Wall Mounting (Optional) For some applications, you will find it convenient to mount Moxa EDS-P510 on the wall, as shown in the following illustrations: STEP 1—Remove the aluminum DIN-Rail attachment plate from the rear panel of the EDS-P510, and then attach the wall mount plates with M3 screws, as shown in the figure at the right. -
Page 11: Wiring The Relay Contact
ATTENTION This unit is a built-in type. When the unit is installed in another piece of equipment, the equipment enclosing the unit must comply with fire enclosure regulation IEC60950-1/EN60950-1 (or similar regulation). ATTENTION Safety First! Be sure to disconnect the power cord before installing and/or wiring your Moxa EtherDevice Switch. -
Page 12: Wiring The Redundant Power Inputs
FAULT: The two sets of relay contacts of the 6-pin terminal block connector are used to detect user-configured events. The two wires attached to RELAY1 RELAY2 the fault contacts form an open circuit when a user-configured event is triggered. If a user-configured event does not occur, the fault circuit remains RELAY1... -
Page 13: Turbo Ring Dip Switch Settings
Turbo Ring DIP Switch Settings EDS-P510 series are plug-and-play managed redundant Ethernet switches. The proprietary Turbo Ring protocol was developed by Moxa to provide better network reliability and faster recovery time. Moxa Turbo Ring’s recovery time is less than 300 ms (Turbo Ring) or 20 ms (Turbo Ring V2) —compared to a 3- to 5-minute recovery time for commercial switches—decreasing the possible... -
Page 14: Led Indicators
NOTE You must enable the Turbo Ring function first before using the DIP switch to activate the Master and Coupler functions. NOTE If you do not enable any of the EDS-P510 switches to be the Ring Master, the Turbo Ring protocol will automatically choose the EDS-P510 with the smallest MAC address range to be the Ring Master. - Page 15 (10/100M) Data is being transmitted at Blinking 10/100Mbps. G1~G3 port’s 10/100Mbps link is inactive. G1~G3 port’s 1000 Mbps link is active. G1~G3 Blinking Data is being transmitted at 1000 Mbps. GREEN (1000M) G1~G3 port’s 1000 Mbps link is inactive. Power is being supplied to Powered Device (PD) AMBER Blinking PoE port is in Power-Fail status...
- Page 16 Specifications of SPL-24 Technology Standards IEEE802.3af Interface RJ45 Ports 10/100BaseT(X) for PoE IN, and 10/100BaseT(X) for DATA OUT LED Indicators Power Power Input voltage 44 to 75 VDC Output voltage 24 VDC Output current 0.54 A @ 24V Output Power 12.95 W (@ 24VDC) Connection Removable “3-pin”...
-
Page 17: Front View
SLP-24 Panel Layout Top View Front View Rear View DATA OUT OUTPUT : 24 VDC PoE IN Heat dissipation orifices Terminal block for power input and grounding Moxa Logo PoE power LED DATA-OUT port PoE IN port DIN-Rail Mounting Dimensions (unit = mm) 10.5 24.87 DATA OUT... - Page 18 DIN-Rail Mounting for SPL-24 The plastic DIN-Rail attachment plate should already be fixed to the back panel of SPL-24 when you take it out of the box. If you need to reattach the DIN-Rail attachment plate, make sure the stiff metal spring is situated towards the top, as shown in the figures below.
- Page 19 Wiring the SPL-24’s Power Outputs The two left-most contacts of the 3-contact terminal block connector on the SPL-24’s top panel are used for 24 VDC output. Top and front views of one of the terminal block connectors are shown here. STEP 1: Insert the negative/positive DC wires into the V-/V+ terminals.
Need help?
Do you have a question about the EDS-P510 Series and is the answer not in the manual?
Questions and answers