1. Manuals
  2. Brands
  3. Power Fist Manuals
  4. Power Tool
  5. 8045901
  6. Manual

Power Fist 8045901 Manual

Rotary tool kit
Hide thumbs
Table of Contents

Advertisement

Available languages

Available languages

Quick Links

INtroductIoN
The rotary tool is a multi-purpse tool able to cut, drill, polish, grind and sand, depending on the accessory
attached to the collet. It works on a high speed, low torque principle that can attain 30,000 RPM compared to
the typical 2,800 RPM of an electric drill. The speed, combined with the proper accessory does all the work.
The user simply holds and guides the tool for it to do the job.

SpecIfIcatIoNS

No load speed:
8,000 to 30,000 RPM
Current draw:
120V, 1 A
ImportaNt Safety precautIoNS
WARNING! Read and understand all instructions. Keep this manual for the safety
warnings and precautions, operating, inspection, maintenance and instructions. When
using this tool, basic precautions should always be followed, including the following.

WORK AREA

1. Keep your work area clean and well lit. Cluttered and dark areas invite accidents.
2. Operate in a safe work environment. Do not use machines or power tools in damp or wet
locations. Do not expose to rain. Do not use power tools in the presence of flammable gases or
liquids.
3. Keep children, bystanders and visitors away from the work area. Do not let them handle tools
or extension cords. No one should be in the work area if they are not wearing suitable protective
equipment.
4. Store unused equipment. When not in use, tools must be stored in a dry location to prevent rust.
Always Lock up tools and keep them out of reeach of children.

PERSONAl SAfEty

1. Use eye and ear protection. Always wear ANSI approved impact safety goggles. Wear a full face
shield if you are producing metal filings or wood chips. Wear an ANSI approved dust mask or
respirator when working around metal and wood dusts. Wear ANSI approved earplugs.
2. Do not over reach, keep proper footing and balance at all times. Proper footing and balance
enables better control of the tool in unexpected situations.
3. Dress properly, wear protective equipment. Do not wear loose clothing or jewelry as they can be
caught in moving parts. Tie back long hair. Protective, electrically non-conductive clothes and
non-skid footwear are recommended when working.
4. Stay alert, watch what you are doing and use your common sense. Do not operate any machine
or tool when you are tired, under the influence of drugs, alcohol or medication.
5. Use clamps or other practical ways to secure and support the work piece to a stable
platform. Holding the work piece by hand or against your body is unstable and may lead to loss of
control.
For any technical questions, please call 1-800-665-8685
rotary tool
Kit
1
8045901

Advertisement

Table of Contents
loading

Related Manuals for Power Fist 8045901

Summary of Contents for Power Fist 8045901

  • Page 1: Specifications

    8045901 rotary tool INtroductIoN The rotary tool is a multi-purpse tool able to cut, drill, polish, grind and sand, depending on the accessory attached to the collet. It works on a high speed, low torque principle that can attain 30,000 RPM compared to the typical 2,800 RPM of an electric drill.

  • Page 2: Electrical Safety

    tOOl USE AND cARE 1. Use the right tool for the job. Do not attempt to force a small tool or attachment to do the work of a larger industrial tool. The tool will perform better and safer at the task for which it was intended. Do not modify this tool or use for a purpose for which it was not designed.

  • Page 3: Accessory Installation

    SPECIFIC SAFETY INSTRUCTIONS 1. Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator. acceSSory INStallatIoN With the shaft lock engaged, loosen the collet nut by hand.

  • Page 4: Maintenance

    lOw SPEEd USES: certain materials (some plastics, for example) require a • Brush Cover Speed Collet Lock relatively slow speed because at high speed the friction Dial of the tool generates heat and causes the plastic to melt. Slow speeds usually are best for polishing operations employing the felt polishing accessories.

  • Page 5: Fiche Technique

    8045901 ensemble d'outils rotatifs INtroductIoN L’outil rotatif est un outil polyvalent servant à couper, à percer, à polir, à meuler et à poncer, selon le type d’accessoire fixé au mandrin à pince. L’appareil se base sur le principe de fonctionnement à grande vitesse et à...

  • Page 6: Entretien

    Habillez-vous de manière appropriée. Ne portez pas de bijoux ni de vêtements amples. Tenez vos cheveux, vos vêtements et vos gants à l'écart des pièces mobiles. Des vêtements amples, des bijoux ou des cheveux longs qui pourraient être happés par une pièces mobile augmentent le risque de blessures corporelles. Restez sur vos gardes.

  • Page 7: Consignes De Sécurité Spécifiques

    CONSIgNES dE SéCURITé SPéCIFIqUES 1. tenez les surfaces de serrage isolées de l’outil lors des travaux où l’outil de coupe pourrait venir en contact avec un fil caché ou avec son propre cordon. Tout contact avec un fil sous tension aura pour effet de transmettre une charge électrique aux pièces métalliques de l’outil;ceci augmente le risque de choc électrique pour l'utilisateur.
  • Page 8 Avertissement ! évitez d’utiliser une meule dont le diamètre est supérieur à 1 po. les meules plus grandes fixées à un outil fonctionnant à grande vitesse ont tendance à se détacher brusquement, augmentant ainsi le risque de blessure. APPlICATIONS à FAIblE vITESSE : •...

Table of Contents