Related Manuals for CTC Union FSW3224
Summary of Contents for CTC Union FSW3224
-
Page 1: User Manual
USER MANUAL FSW3224 24 + 2G Web Smart Switch CTC Union Technologies Co., Ltd. Version 1.01 2006/01... -
Page 2: Table Of Contents
24+2G Web Smart-switch User Manual 1. GETTING START .............................7 ONNECTING TO THE WITCH ONSOLE ..............7 PC COM P ETTING ......................7 ONNECTING TO THE WITCH ................7 1.3.1 Advantage of Web Smart Switch..................8 OPERATION NOTICE..........................9 2.1. ONSOLE UNCTION ......................9 2.2. ONSOLE CTION .......................9 LOGIN................................ - Page 3 24+2G Web Smart-switch User Manual 4.9.7. IP Configuration......................26 WEB USER INTERFACE........................27 5.1. ELCOME PAGE ..........................27 5.2...........................27 5.3. TATUS ..........................27 5.4. ONFIGURATION ......................28 5.5. RUNK ONFIGURATION ......................29 5.6. VLAN C ONFIGURATION ......................30 5.6.1. VLAN Mode: Port-based VLAN................31 5.6.2.
- Page 4 24+2G Web Smart-switch User Manual 1. Introduction 24+2G SMART is a high performance switch that provides users with 24 10/100Mbps Ethernet and 2 1000Mbps Gigabit ports. The Gigabit module, which can be copper or fiber media, supports 1000BASE-SX, 1000BASE-LX or 1000BASE-T, allowing users to increase their network response time at gigabit speeds and with great flexibility.
- Page 5 24+2G Web Smart-switch User Manual 1.2. Installation Follow the guidelines below to install the Switch. Do not place any object weighted more than 3Kg (6.6 lb) on the Switch. Connect the power cord to the Switch and the power outlet. Leave at least 10 cm (4 inches) of space around the Switch for heat dissipation.
-
Page 6: Led Indicators Information
24+2G Web Smart-switch User Manual LED indicators information Color Status Solid Blinking Power Green Power is applied to this device DIAG Performing self diagnostic Green Self diagnostic successful (after Power On) Cooling Left cooling fan failed Fans LINK/ACT Green 10Mbps Ethernet connection speed TX/RX activity or (1 ~24 port) Collision... -
Page 7: Getting Start
24+2G Web Smart-switch User Manual 2. Getting Start 2.1. Connecting to the Switch Console Port Users can use a RS-232 non-crossover serial cable to connect the PC’S COM port to the switch console port. The switch system provides the RS-232 interface with baud rate 9600-8-n-1. Use terminal emulation program ( e.g. -
Page 8: Advantage Of Web Smart Switch
24+2G Web Smart-switch User Manual 2.3.1. Advantage of Web Smart Switch No proprietary program, no installation, no learning. It’s the most painless way for IT/MIS person to use, Cross-platform support. You could configure the switch by web browser on any platform (e.g. Windows ME, Windows XP, Windows Server 2003, UNIX, Linux, Macintosh …... -
Page 9: Operation Notice
24+2G Web Smart-switch User Manual 3. Operation Notice 3.1. Console Function Keys The following generic function keys provide functon in all of the menus: Fuction Tab/ Move the cursor to right item. Backspace/ Move the cursor to left item. ↑ Move the cursor to up item. -
Page 10: Login
24+2G Web Smart-switch User Manual 4. Login 4.1. Power-On Self Testing When the power is supplied to the switch system, power-on self testing is running. The result of power-on self testing is output to the console port. Each diagnostic item has either “Passed” or “Failed”... -
Page 11: Web Login
24+2G Web Smart-switch User Manual 4.3. Web Login 4.3.1. Setting IP Address by Console Port When you are going to login to the web pages, you have to set the IP address properly first. You could login with the default IP address: 192.168.1.1. But you have to make sure this IP could work in your network environment. -
Page 12: Login With A Web Brower
24+2G Web Smart-switch User Manual 4.3.2. Login with a Web Brower When you connect to the switch with a web browser, a login screen is displayed. Enter a user name and password to login to access the switch. Items Option Default Value Username Max: 6, Min:1 characters, case sensitive... - Page 13 24+2G Web Smart-switch User Manual System Information Logout Logout and login menu. Revision 1.0-...
-
Page 14: Port Status
24+2G Web Smart-switch User Manual 5.2. Port Status Display current status: enabled/disabled, link up/down, speed/duplex and flow control of each port. Item Description Enable Enable / Disable Link Status Up/Down. If the port was disabled, the item is displayed as “---“ . Spd / Dpx 100F/ 100H/ 10F/ 10H. -
Page 15: Trunk Configuration
24+2G Web Smart-switch User Manual Notice: In this example, when Port 3 and Port 4 are configured to be trunk group 1, thus Port3/Port4 will be disappeared from the list and replaced by Trunk 1 indication. 5.4. Trunk Configuration Configure the trunk groups. There are max. 7 trunk groups can be configured. User can arbitrarily select up to four ports from port1~port24 or port25~port26 to make a trunk group. -
Page 16: Vlan Configuration
24+2G Web Smart-switch User Manual 5.5. VLAN Configuration A Virtual LAN (VLAN) is a logical network group that limits the broadcast domain. It allows you to isolate network traffic so only member of the VLAN receive traffic from the same VLAN members. Basically, creating a VLAN within a switch is logically equivalent of reconnecting a group physically. -
Page 17: Vlan Mode: Port-Based Vlan
24+2G Web Smart-switch User Manual 5.5.1. VLAN Mode: Port-based VLAN Packets can be forwarded only to members of the same VLAN group. Special items in the Action Menu: <Add>: Add a new group and enter the editing page. <Delete>: Delete an existing group. Item Option Default value... -
Page 18: Port-Based Vlan Group
24+2G Web Smart-switch User Manual 5.5.2. Port-based VLAN Group <Add>/<Edit>Menu Packets are delivered to only members of the same VLAN group. Note all unselected ports are treated as belonging to another single VLAN. If the port-based VLAN enabled, the VLAN-tagging is ignored./ Menu -
Page 19: Vlan Mode: 802.Iq Vlan
24+2G Web Smart-switch User Manual 5.5.3. VLAN Mode: 802.IQ VLAN Packets are delivered to the members of the same VLAN group, which is recognized by 802.IQ tag. PVID(Port VID): Set the port VLAN ID that will be assigned to untagged traffic on a given port. This feature is useful for accommodating devices that you want to participate in the VLAN but don’t support tagging. -
Page 20: Advanced 802.1Q Vlan Configuration
24+2G Web Smart-switch User Manual 5.5.5. Advanced 802.1Q VLAN Configuration Ingress filters configuration. 5.6. Port Monitoring Configuration Port monitoring is forwarding specified direction of packets from several monitored ports to a specified monitoring port. Items Option Default value Port Monitoring Mode Disable / RX / TX / RX &... -
Page 21: Qos Configuration
24+2G Web Smart-switch User Manual Each single port and trunk group could be a member. 5.7. QoS Configuration Configure QoS mode, 802.1p priority and static port priority. Items Option Default value Qos Mode Disable / all high before low / weight 3:1 /5:1 / 7 :1 Weight3:1 Each port Off / Low / High 802.1p Priority... -
Page 22: Misc Operation
24+2G Web Smart-switch User Manual Configure input rate or output rate of each port. For example: assume port 1 is 10Mbps, users can set it's effective Output Rate to 1Mbps, Input Rate to 500Kbps. XP-3241 will perform flow control or backpressure to confine the to ingress rate to meet the specified rate. -
Page 23: Advanced Switch Configuration
24+2G Web Smart-switch User Manual 5.9.1. Advanced Switch Configuration Configure advanced switch functions: BSF, Collision retry, age-out time... Items Option Default value Broadcast Storm Filter Off / 5% / 10% /20% Collision Retry Forever Disable / Enable Disable MAC Table Auto-Aging Disable /150 / 300/ 600 seconds 300 seconds MAC Hash... -
Page 24: Password Setting
24+2G Web Smart-switch User Manual 5.9.2. Password Setting You should change the default password to be sure that your system is secured. Items Option Default value Password Protection Enable / Disable Enable User name Max: 6, Min: 1 characters, case sensitive New Password Max: 6, Min 1 characters, case sensitive Re-enter Password... -
Page 25: System Information
24+2G Web Smart-switch User Manual 5.9.5. System Information This page displays the firmware version and chip version. 5.9.6. Update Firmware Please reference Appendix A that detail upgrade method. Revision 1.0-... -
Page 26: Ip Configuration
24+2G Web Smart-switch User Manual 5.9.7. IP Configuration Configure IP address, subnet mask and default gateway of the switch. Items Option Default Value IP Address ***.***.***.*** 192.168.1.1 *is represent a digit from 0~9,***is range from 0 to 255. Subnet Mask ***.***.***.*** 255.255.255.0 *is represent a digit from 0~9,***is range... -
Page 27: Web User Interface
24+2G Web Smart-switch User Manual 6. Web User Interface 6.1. Welcome page This is page will show switch information includes the firmware and software massage. 6.2. Main Menu This is the main menu of the switch web software. Item Description Port Status Display current status: enabled/disabled, link up/down, speed/duplex and flow control of each port. -
Page 28: Port Configuration
24+2G Web Smart-switch User Manual 6.4. Port Configuration Configure enable state, auto-negotiation, speed/duplex, and flow control for each port. Items Option Default value Enable Enable / Disable Enable Auto On /Off. If the port was disabled, the item is displayed as “---“ . If this set to Off, then Spd/Dpx should not be set to Auto. -
Page 29: Trunk Configuration
24+2G Web Smart-switch User Manual Notice: In this example, Port 3 and Port 4 are belonging to trunk group 1, thus Port3/Port4 are disappeared and replaced by Trunk 1. 6.5. Trunk Configuration Configure the trunk groups. There are max. seven trunk groups can be configured. User can arbitrarily select up to four ports from port 1~port 24 or port 25~port 26 to make a trunk group. -
Page 30: Vlan Configuration
24+2G Web Smart-switch User Manual 6.6. VLAN Configuration A Virtual LAN (VLAN) is a logical network group that limits the broadcast domain. It allows you to isolate network traffic so only members of the VLAN receive traffic from the same VLAN members. Basically, creating a VLAN within a switch is logically equivalent of reconnecting a group of network devices to another Layer 2 switch. -
Page 31: Vlan Mode: Port-Based Vlan
24+2G Web Smart-switch User Manual 6.6.1. VLAN Mode: Port-based VLAN Packets are delivered to only the members of the same VLAN group. Special buttons : <Add New>: Add a new group and enter the editing page. <Delete>: Delete an existing group. 6.6.2. -
Page 32: Vlan Mode: 802.1Q Vlan
24+2G Web Smart-switch User Manual Group ID 1~255 (max. 24 VLAN group) Each port --- / Member 6.6.3. VLAN Mode: 802.1Q VLAN Packets are delivered to the members of the same VLAN group, which is recognized by 802.1Q tag. PVID (Port VID): Set the port VLAN ID that will be assigned to untagged traffic on a given port. This feature is useful for accommodating devices that you want to participate in t he VLAN but that don't support tagging. -
Page 33: Advanced 802.1Q Vlan Configuration
24+2G Web Smart-switch User Manual and outgoing frames are NOT VLAN-tagged frames. 6.6.5. Advanced 802.1Q VLAN Configuration Ingress filters configuration. 6.7. Port Monitoring Configuration Port monitoring is forwarding specified direction of packets from several monitored ports to a specified monitoring port. Items Option Default value... - Page 34 24+2G Web Smart-switch User Manual Monitoring Port PORT1~PORT24, PORT25~26. PORT 1 Any single port and trunk group Monitored Port --- / Monitored. Each single port and trunk group could be a member Revision 1.0-...
-
Page 35: Qos Configuration
24+2G Web Smart-switch User Manual 6.8. QoS Configuration Configure QoS mode, 802.1p priority and static port priority. Items Option Default value Qos Mode Disable / all high before low / weight 3:1 / 5:1 / 7:1 Weight 3:1 Each port Off / Low / High 802.1p Priority Low / High... -
Page 36: Misc Operation
24+2G Web Smart-switch User Manual 6.10. Misc Operation Miscellaneous operation of the switch. Item Description Advanced Switch Configuration Configure advanced switch functions: BSF, Collision retry, age-out time … Password Setting Change user name and password Restore S ystem Default Setting Restore to manufacture default. -
Page 37: Advanced Switch Configuration
24+2G Web Smart-switch User Manual 6.10.1. Advanced Switch Configuration Configure advanced switch functions: BSF, Collision retry, age-out time... Items Option Default value Broadcast Strom Filter Off / 5% /10% / 20% Collision Retry Forever Disable / Enable Disable MAC Table Auto-Aging Disable / 150 / 300 / 600 seconds 300 seconds MAC Hash... -
Page 38: Restore System Default Setting
24+2G Web Smart-switch User Manual 6.10.3. Restore System Default Setting Restore to default manufacture setting. 6.10.4. Reboot System Reboot the switch system. Revision 1.0-... -
Page 39: Ip Configuration
24+2G Web Smart-switch User Manual 6.10.5. IP Configuration Configure IP address, subnet mask and default gate way of the switch. Items Option Default value IP Address ***.***.***.*** 192.168.1.1 *is represent a digit from 0~9,***is range from 0 to 255. Subnet Mask ***.***.***.*** 255.255.255.0 *is represent a digit from 0~9,***is range from... -
Page 40: Appendix A
24+2G Web Smart-switch User Manual Appendix A Firmware upgrade instruction manual Introduction: 1. Firmware version no of 4.21 is an initial release version, all further upgrade version will base on version no. 4.21. There is a firmware upgrade utility of 8055ISP writer will also be required prior to process upgrade processes. - Page 41 24+2G Web Smart-switch User Manual 2. Before you are login that you would be required to input the user name and smart password. Please use as an user name and as a password, and go to the Misc operation page, select item # 5 of update firmware so that enable to process into firmware upgrade.
- Page 42 24+2G Web Smart-switch User Manual 4. In this page, that you need to terminate the connection mode as below show figure. Since switch product supports ONLY one connection and in order to use firrware upgrade utility that this process is required. 5.
- Page 43 24+2G Web Smart-switch User Manual 6. Please select image.bin by icon of Select BankQ as below figure shown. Revision 1.0-...
- Page 44 24+2G Web Smart-switch User Manual 7. When the target firmware was selected that you need to click on ConNect icon as below figure shown, then you will be read about the baud rate of 57600 as below figure shown.. 8. Please click on program all for firmware upgrade, when the firmware is upgraded there is a message about process completion .
- Page 45 24+2G Web Smart-switch User Manual 9. To identify the firmware upgrade process that you need to re-boot switch in order to verify the product model whether has been changed to 24+2 Web Smart Switch. Revision 1.0-...
- Page 46 24+2G Web Smart-switch User Manual Below fighre shown the firmware was upgraded sucessfully. Revision 1.0-...