Variables Under "Settings 1 - Electrolux W4400H Service Manual

116
Variables under "SETTINGS 2"
SETTINGS 2
HEATING RELAY ON WHEN NOT HEATED
TEMPERATURE INCREASE ALLOWED
LEVEL EMPTY
LEVEL OVERFILL
PAUSE TEST LEVEL
PAUSE TEST TEMPERATURE
Y/N
HEATING RELAY ON IF NOT HEATED
TEMPERATURE INCREASE ALLOWED
LEVEL EMPTY
LEVEL OVERFILL
PAUSE TEST LEVEL
PAUSE TEST TEMPERATURE
DEFAULT TEMPERATURE HYSTERIS
TEMPERATURE STEP IN COOL-DOWN
DEFAULT LOW EXTRACT TIME
DEFAULT MEDIUM EXTRACT TIME
DEFAULT HIGH EXTRACT TIME
DEFAULT DRAIN TIME
DEFAULT DISTR. TIME
DO UNBALANCE MEASUREMENT
DRAIN OPEN DELAY
START EXTRACT TIME
ROLLOUT TIME
PAY PER WASH ALARM
LOCK TEST DELAY
DRAIN TIME WHEN OVERFILL
OIL LUBRICATION HOURS
PULSE TIME OIL LUBR. SEC
AMOUNT OF I/O MODULES (1-)
DELAY CLEAR DOOR TEXT
TIMEOUT DRAIN AT PROGRAM START
TIMEOUT DURING PAUSE
MINIMUM TEMPERATURE INCREASE
DOOR OPEN DELAY FOR MOTOR LOST
ERROR, NO WATER
ERROR, OPEN DOOR
ERROR, DOOR LOCK
ERROR, LOW TEMPERATURE
ERROR HIGH TEMPERATURE
ERROR, WATER IN MACHINE
ERROR, NO HEAT
ERROR, REMAINING WATER
ERROR, UNBALANCE SWITCH
ERROR, MOTOR COMMUNICATION
ERROR, LEVEL ADJUST
ERROR, EMERGENCY STOP
ERROR, WEIGHT FROM SCALE
ERROR, DOOR LOCK SWITCH
ERROR, START NOT ALLOWED
ERROR, MIS COMMUNICATION
ERROR, EWD INTERLOCK
ERROR, I/O COMMUNICATION
ERROR, LOW OIL LEVEL
ERROR, LOW OR HIGH VOLTAGE
ERROR, ERROR CODES FROM MOTOR
ERROR, PRESS. SENSOR TILT
ERROR, PRESSURE SENSOR TIMEOUT
ERROR, DOOR SWITCH TILT
ERROR, LEVEL OFFSET
ERROR, LEVEL SYSTEM NOT CALIB
TIME DELAY BEFORE DOOR OPENING
UPPER TEMPERATURE FOR ERROR
LOWER TEMPERATURE FOR ERROR
MAX ADJUST TEMPERATURE
MAXIMUM EXTRACT SPEED
DEFAULT WASH SPEED
DISTRIBUTION SPEED
DEFAULT LOW EXTRACT RPM
DEFAULT MEDIUM EXTRACT RPM
DEFAULT HIGH EXTRACT RPM
START EXTRACT SPEED
DEFAULT WASH ACCELERATION
DISTRIBUTION ACCELERATION
EXTRACT ACCELERATION
START EXTRACT ACCELERATION
EXTRACT RETARDATION
MAX SPEED DURING FILLING
MAX LEVEL OFFS. FOR AUT. CALIB.
TIME AT DISTRIBUTION SPEED 2
NUMBER OF REDIST LOW 1 UNB.
NUMBER OF REDIST LOW 2 UNB.
NUMBER OF REDIST MEDIUM UNB.
NUMBER OF REDIST HIGH UNB.
NUMBER OF REDIST EXTREME UNB.
DRAIN TIME AT PROG. START
DRAIN TIME AT PROG. END
READY
Programme unit
When the top line of a menu
Y
Y is highlighted you have the
90
option of scrolling down
200
0
-18°C through the menu faster by
pressing . When you
do, the next portion of the
menu is displayed, with its
last line highlighted.
Y
Y
90
200
0
-18 °C
4 °C
4 °C
00:00
00:00
00:00
00:00
00:00
N
0:1
00:0
Answer the questions using
00:01
0
the function key or the
0:10
numeric keys.
0:05
100
0:01
1
04:00
4:00
Press to move on to
0:00
the next question.
5 °C
1:00
Y
Y
You can go back and
Y
Y
change a question you
Y
have answered already by
Y
Y pressing repeatedly.
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
0:0
98°C
-9 °C
97 °C
1200
48
90
550
700
900
1000
20
9
40
40
50
100
Different types of question
The questions in the various modules are of
two different types, each of which needs to be
answered in a different way:
Yes/No questions
The function key display shows Y/N , which
is a toggle function (the letter to the right of the
highlighted question toggles between N and Y
each time it is pressed).
Times, temperatures, water levels
To answer these questions, use the numeric
keys. The number of digits required will vary. If
you make a mistake while entering digits, de-
lete it by pressing ERASE one or more times.
No confirmation of value entered
Once you have entered the right value, you
simply move on to the next by pressing
There is no enter or return key to press to
confirm each value.
To alter the value for a question you have
already answered
Press to highlight the question you want,
then simply change the value.
Confirm changes before you exit Settings 2
If you have changed any of the variables, this
change must be confirmed when you exit Set-
tings 2. To do this you have to use a strap to
short-circuit two terminals on the CPU board, see
section headed "To conclude making changes in
variables under SETTINGS 2".
.