Wansview HD Outdoor IP Camera W2(1080P)/W3(720P) User Manual We keep improving the app, if the app interface is not accordance with the instructions, please go to wansview website: http://www.wansview.com for the latest instructions. Revised on 1st January 2018 www.wansview.com...
Or scanning the QR code to enter our Youtube channel. Important Security Warning In order to keep your Wansview camera secure and prevent unauthorized access, please make sure to follow the steps below: 1. The camera has always the latest firmware installed. If we update the firmware, we upload it on www.wansview.com/Service/download/...
Page 6
IP Camera W2(1080P)/W3(720P) 6. Operation and Maintenance Do not touch the camera sensor or lens directly. To clean dust or dirt off of the lens, use an air blower or a microfiber cloth. 7. Accessories Be sure to use only the accessories recommended by the manufacturer.
IP Camera W2(1080P)/W3(720P) 1. Features and Specifications The Wansview Full HD IP Camera is an integrated outdoor IP Camera developed specifically for network video applications. 1.1 Product Profile 1 Antenna:2.4G 3dBi WiFiAntenna 2 infrared LEDS 3 1/2.7” Full HD sensor...
2. Connect the IP camera and router with the network cable. 3. Power on the camera with the provided adapter (please verify voltage). 3. Launch the Wansview app and click on . Scan the QR Code and input default user name (admin) and password (123456).
Page 10
IP Camera W2(1080P)/W3(720P) ·Launch the Wansview app, click to access Add Camera page and select “Add camera via wired method”, then follow the wizard step by step. Add camera Set up camera Power camera on and connect it to router using...
IP Camera W2(1080P)/W3(720P) 2.2 WiFi Setting If want to set up WiFi, tap the “OK” , then app will search the available WiFi, choose your router’s 2.4G WiFi(Attention: Special characters “ &” and “ , ” cannot be contained in the WiFi name and password), and input correct WiFi password (Case sensitive), then “Next”.
IP Camera W2(1080P)/W3(720P) When the camera shows “Online”, tap “>” to Advanced Settings > User Setting to change the default User name and Password. This process is outlined in 2.6.2 User Setting. 2.3 Live Streaming Each camera can be accessed by up to 4 users at the same time.
Page 13
IP Camera W2(1080P)/W3(720P) Flip/Mirror: If the live video is upside down because of the installation, tap to make it right. Exit: Turn off the live feed screen. Viewing Camera on Multi-View User can monitor several cameras (Max. 4 )at the same time on Multi-View.
IP Camera W2(1080P)/W3(720P) 2.4 Local Picture and Record record snap During live streaming, user can take snapshots by tapping on Snapshot to phone and Record to phone. To stop recording, tap again or exit from the live streaming. In Local Picture and Record, User can find all the pictures and videos taken manually.
Follow the below steps to set up alarm. Alarm Deployment this is for camera that can connect external source of alert device. The IO Detection: W2/W3 is not available. Sensor Type: For external source of alert device. The external sensor can be always open or always close.
Page 16
When an alarm is detected, the camera will send a video to your FTP server. For FTP paramters, please refer to Page 40 Save Picture to SD/TF: unavailable(W2/W3 cannot support SD card) Save Record to SD/TF: unavailable(W2/W3 cannot support SD card) Trigger IO Output: Not available for W2/W3.
Tap WiFi Setting, and search the available WiFi, choose the WiFi and manually input the WiFi Password, then tap to save the WiFi information. User can unplug the ethernet cable when the app appears “WiFi Set Succeed”. Note: Wansview camera only supports 2.4Ghz WiFi, and wifi password should be no longer than 31 characters.
IP Camera W2(1080P)/W3(720P) 2.6.2 User Setting/Management Under the User Settting/Management, user can change the default username(admin) and password (123456), or create another user account with certain access rights, such as an Operator or Viewer account for other person to view the camera.
IP Camera W2(1080P)/W3(720P) Add another user account On User Setting, tap to add user, manually add the username and password, then choose the Role(Operator or Viewer). Administrator: Full access rights Operator: Can operate on the camera live video screen, but not access to other settings like Alarm setting, Advanced Settings etc.
IP Camera W2(1080P)/W3(720P) 2.6.4 Misc Setting On Misc Setting, user can set up OSD (On Screen Display), Microphone/ Speaker Volume and AC Frequency. OSD Setting Click “OSD Setting” to set: Overlay time: Camera time in live streaming, recording and pictures...
Page 21
IP Camera W2(1080P)/W3(720P) Volume Setting If volume of the “Talk” and “Listen” is too low, user can adjust it from Volume Setting AC Frequency User can adjust the power frequency, power frequencies include:50HZ(220V voltage selects 50HZ), 60HZ(110V Voltage selects 60HZ).
IP Camera W2(1080P)/W3(720P) 2.6.5 Maintenance Reboot camera if camera is always loading or if the camera/app is frozen. No need to set up again. If camera restores to factory default, the set up procedure needs to be repeated again after reboots.
IP Camera W2(1080P)/W3(720P) 2.7 Start Video Tap “Start Video” to broadcast the camera live streaming. 2.8 Delete device Tap “Delete device”, user can delete the camera from the app.
2.9 Message On the Message, user can check the alarm message. 2.10 More Record and pictures are the local files recorded from the wansview app. Multi-View: Please refer to P 14 Push Set:Currently not available About:Can check the wansview app...
IP Camera W2(1080P)/W3(720P) 3. PC Client Software 3.1 Add Camera 3.1.1 Add camera in Lan 1) Tap to add camera 2) Search the camera in Lan, DID number will be searched if use DID(P2P) to search, while Search IP will get IP Address 3) Click the searched camera, and the camera information will be filled automatically.
2) Manually input the camera information. Tips: DID number can be checked from stickers on the back of the camera. You can check the DID from Wansview app If you have already added the camera on the mobile phone “wansview” app.
IP Camera W2(1080P)/W3(720P) When play the video, but only shows black, please go to Setting --Other Setting to choose the No GPU Display in the Video Display mode. 3.2.2 Stop Video Click to stop the video or right-click the camera and choose “Stop”...
IP Camera W2(1080P)/W3(720P) 3.2.3 Video Interface Attention: Resolution cannot be adjusted during recording, user needs to stop the recording, then switch the resolution. left right down Play/stop Resolution Snap Flip Record Mirror Listen Talk 3.3 Camera Settings 3.3.1 Edit Device Right-click the camera info and select”Edit Device”, here can change the Device Name and...
IP Camera W2(1080P)/W3(720P) 3.3.2 Advanced Settings On the Advanced Settings, user can check camera firmware version, set up time, create other account for operater or Visitor, set up WiFi and SD card recording etc. 3.3.2.1 Device Info User can check the camera status and Mac address, and check the camera’s firmware version.
IP Camera W2(1080P)/W3(720P) 3.3.2.3 User Setting User can create other accounts for family member or friends in User Setting. Add an account with user name and password, and give a right to this account. Tips: Administrator: All settings can be edited Operator: Can operate all the icons (such as listen, talk, flip/mirror) on the live video page.
IP Camera W2(1080P)/W3(720P) 3.3.2.4 Unavailable for W2/W3 User can set up WiFi for the camera is connected Ethernet cable, or change to other available WiFi. Search the available WiFi, and choose the one you want to connect, then input the WiFi password (click the icon behind to confirm if the password is correct).
IP Camera W2(1080P)/W3(720P) User can record video to SD card. Before recording, please kindly make sure you have inserted a SD card, and format it. the record length can be set 2-15 minutes 3.3.2.6 Other Setting 1) OSD setting On the OSD setting, users can set up the Overlay name and Overlay time, so user can check name and time on the video screen.
IP Camera W2(1080P)/W3(720P) 3) AC Frequency User can adjust the power frequency, Power frequencies include: 50HZ(220V voltage selects 50HZ), 60HZ(110V voltage selects 60HZ), 60HZ used in Japan, Canada etc. 4) Maintenance User can reboot and reset (restore) the camera. Tips: To reset the camera, the camera will restore to factory setting.
IP Camera W2(1080P)/W3(720P) 3.3.3.1 Motion Detection User can set up motion detection area here to narrow the motion detected area to some important places, tick each window, move your mouse to the lower right corner and drag it can adjust the size of the window, and can move it to the needed area.
IP Camera W2(1080P)/W3(720P) 3.3.3.3 Linkage Alarm If user set up alarm, the camera will execute a variety of alarm actions at linkage: snap to email, snapshot and video to FTP, snap and video to SD card. And if you connect external I/O alarm device, it can trigger alarm too.
Page 36
IP Camera W2(1080P)/W3(720P) Email Sender setting Email address: service2@wansview.com Email Password: SMTP Server: smtp.qiye.163.com SMTP Port: Security Type: NONE email, it should be the same Sender: service2@wansview.com with "Email address" Receiver Setting E-mail subject: alarm any information Q3 alarm E-mail content: Receiver 1: service@wansview.com...
IP Camera W2(1080P)/W3(720P) 3.3.3.4 Alarm Time After setting the type of alarm and alarm action, please set up the alarm time, the alarm action can only be triggered when armed. The Green color means the time is armed. User can choose “All Time” or “Clear Time”, and can also choose a specific time. 15 mintues for a interval.
IP Camera W2(1080P)/W3(720P) 3.4 Multi-View User can monitor multiple cameras at the same time, 4-screen, 9-screen, M(6, 8,16, 25, 36) and full screen can be set up according to different demands 3.5 Local Setting About software: Basic setting: User can set up lock screen password in case you won’t let others to see the video.
IP Camera W2(1080P)/W3(720P) 3.6 Scheduled Recording Before recording to your local computer, please make sure you set up the Record Path on the “Local Setting”. Then follow the below steps to set up the recording: 1: Click “Create” to create a Record name, it will give you a name automatically(combination of date and time), user can edit the name.
IP Camera W2(1080P)/W3(720P) 3.7 Playback On “Playback” page, user can playback the recorded videos on the local disk and SD card. 3.7.1 Playback Local Record 1) Choose Local Record and selected the camera you want to check. 2) Select the Media Type(Video or Image) 3) Select the video in an exact date you want to playback 4) Recorded video list will be shown (Video starts with “P”...
IP Camera W2(1080P)/W3(720P) 3.7.2 Unavailable for W2/W3 1) Choose SD/TF record and selected the camera you want to check. 2) Select the Media Type(Plan or Alarm) 3) Select the video in an exact date you want to playback 4) Recorded video list will be shown, if it is not shown, please tap to show the list (Video starts with “nrc”...
IP Camera W2(1080P)/W3(720P) 3.8 Lock Lock the screen if you don’t want to operate it or prevent others to operate the camera. The default lock password is 123456. 4. Manage Camera with other Apps and Software Add Camera to iSpy Connect Steps 1.Add IP Camera...
Page 43
IP Camera W2(1080P)/W3(720P) Add the Camera on Blue Iris In IP camera configuration, input: -IP: the camera’s IP address -HTTP port: camera’s port -RSTP port: default 554 -User -Password -Make: Wansview -Model: K1/K2, NCM GA/GB/630W, Q3S RTSP -Path: ch0, or ch1 or ch2...
IP Camera W2(1080P)/W3(720P) 5. Web Access 5.1 Settings To view your camera in any web browser you’ll need the camera’s IP address and camera’s Port. If your computer is in the same network, just type the address in browser address bar: http://IP:PORT for example http://113.116.100.223:80.
IP Camera W2(1080P)/W3(720P) 5.1.2 View Video-Mode 1 - Complete Camera Management Click on Download Plugin to download and install the OCX Plugin-HYPlayer plugin. Note: If you use Google Chrome or Firefox you need to install the IE tab: -Firefox > Add-ons > Extensions. Search for IE Tab and install.
IP Camera W2(1080P)/W3(720P) Record: Record and save to PC. Digital Zoom Show/Hide Control Panel. Resolution: Choose 3 resolutions 1920x1080 / 640x360 / 320x180 Use the control panel to pan and tilt your camera’s head. Click to move camera’s head horizontally or vertically. Stop camera movement and it will go to the initial position.(function disabled in this model)
IP Camera W2(1080P)/W3(720P) 5.4 Set Up 5.4.1 System System > Status Data about the current Camera Status System > Time Setting Users can choose to sync time to the PC or to a NTP server. System > Pan & Tilt...
Page 48
IP Camera W2(1080P)/W3(720P) System > Other Settings Turn off Led indicators at your choice. System > Multiple Settings Add up Cameras for multiple 4 view. Get their IP and Port, Input User and Password. Name them. System > Maintenance In System Maintenance...
IP Camera W2(1080P)/W3(720P) System > About In System About users can check the latest camera’s firmware which can be downloaded at www.wansview.com. 5.4.2 Network These functions are meant to be managed by technical specialist except for FTP Server Settings and SMTP Settings. Contact our friendly customer service for specific technical Network >...
Page 50
IP Camera W2(1080P)/W3(720P) Network > Port setting At "Port Setting", the user can change web access port (http port). Port setting range: 80-65535. Pay attention not to conflict with other port values. Network > Wi-Fi setting At "Wi-Fi Set Up", click "Search"...
Page 51
IP Camera W2(1080P)/W3(720P) Network > DDNS setting The user can access the camera via DDNS domain name provided by the manufacturer for free or a third party domain name. Port mapping is required while using domain name to access. The third party domain name supports 3322.org/dyndns.org/No-iP.com.
Page 52
IP Camera W2(1080P)/W3(720P) Network > Onvif setting Onvif is a global standard for the interface of IP-based security products. The ONVIF protocol ensures interoperability between products regardless of manufacturer, allowing you to integrate your IP camera as a generic ONVIF camera into existing security systems.
IP Camera W2(1080P)/W3(720P) Network >SMTP (E-mail) Setting To get started, make sure that your e-mail provider supports SMTP. Then input required parameters. Mainstream E-mail suffixes supported by SMTP include: smtp.gmail.com, mail.yahoo.com, smtp.gmx.com, smtp-mail.outlook.com. Take gmail setting as an example. Server address: SMTP stands for Simple Mail Transfer Protocol.
Page 54
IP Camera W2(1080P)/W3(720P) Video and Audio > Audio Setting (function disabled in this model) Here you can adjust Microphone and Speaker volume Video and Audio > Image Setting Here you can adjust the image parameters brightness, contrast, saturation and hue. You can also flip and mirror the video image...
IP Camera W2(1080P)/W3(720P) Video and Audio > Night Vision Enter "Night Vision Setting" to set IR LED and IRCUT. Once IR LED is off, the IR LED IR cut will not work any longer. 5.4.4 Security To modify /add /delete administrator operator and viewer can be set in this page.
IP Camera W2(1080P)/W3(720P) Security > IP Filtering This screen allows for the filtering of IP addresses, either blocking them or granting them access to the camera. This feature helps make the camera more secure by limiting remote access only to approved users.
Page 57
IP Camera W2(1080P)/W3(720P) Alarm > Motion Detection (Intruder Monitor) The Motion Detection in the Web Interface is more advanced than in the App. User can set up to 4 detection areas and different sensitivity. 15 corresponds to the lower level and 55 to the mid-level.
Page 58
IP Camera W2(1080P)/W3(720P) Once the alarm is set, users will receive a notification on the smartphone (only Android) if the app is running on the background and can choose to get: Snapshot to Email: When an alarm is detected, the camera will send three pictures to the email box.
IP Camera W2(1080P)/W3(720P) 5.4.6 Storage(function disabled in this model) SD Card Management If the card is not readable, please kindly Format the SD card. Storage > SD card Capture (Timed Snapshots) Take Timed snapshots and save them on the SD card Storage >...
IP Camera W2(1080P)/W3(720P) 5.4.7 Log > Local Configuration (not available for MAC users) Enter "Local Configuration". You can set the save path for videos and pictures on your PC as well as the recording duration. Reminders: 1: When using IE9 or higher, please run the browser video path and picture path as "administrator"...