Advertisement
8
FUNCTIONS DESCRIPTION
1. Adjustment mode switch
With this switch, a speedy check of the
beam reception level is possible.
When aligning the beam, turn the switch
to the "Adjustment mode".
(Factory set : Operation mode)
2. Response time adjustment
volume
(Factory set : 0.04)
Response time：0.04 sec.
Run at full speed
9
TROUBLESHOOTING
Solve possible problems according to the following table.
If normal operations cannot be restored by this means, contact either the dealer from
whom you bought the unit or TAKEX.
Symptoms
Possible causes
1. No power supply
Transmitter
2. Bad wiring connection or broken
LED does not
wire, short
light
1. No power supply
2. Bad wiring connection
Receiver LED
does not light
3. Microwave is reflected off another
when the beam
object and sent into the receiver
is broken
1. No power supply to the transmitter
Receiver LED
2. Angle adjustment of transmitter
continues to light
and receiver is not appropriate.
(the does
3. Obstacles between transmitter
not stop)
and receiver
1. Bad wiring connection
2. Change of supply voltage
3. Shading objects between the
Intermittent
transmitter and receiver
alarm
4. A large electric noise source such
as power machine is located near
the transmitter and receiver
5. Installation height, installation site
or angle adjustment is inapporiate
DAILY INSPECTIONS
To clean the device, use a soft, wet cloth and then wipe off any water drops.
●
If the device is particularly dirty, dip the soft cloth in water that includes a weak neutral detergent.
Wipe the device gently with the cloth, then wipe off any detergent that remains.
Do not use substances such as thinner or benzene.
●
(The plastic parts may deform, discolor or change their properties.)
Periodically (approximutely weekly) confirm operation.
12
SPECIAL NOTES
1.FCC
(1)FCC Regulation Statement : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures : -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and
receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help.
WARNING : Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
(2)RF Exposure Warning Statement : This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance. This transmitter must be at least 20 cm from the user and must not be co located or operating in conjunction with any other antenna
or transmitter.
The information in this guide may change without notice. The manufacturer assumes no responsibility for any errors that may appear in this guide.
Limited Warranty :
TAKEX products are warranted to be free from defects in material and workmanship for 12 months from original date of shipment. Our warranty does not cover damage or failure caused by
natural disasters, abuse, misuse, abnormal usage, faulty installation, improper maintenance or any repairs other than those provided by TAKEX. All implied warranties with respect to
TAKEX, including implied warranties for merchantability and implied warranties for tness, are limited in duration to 12 months from original date of shipment. During the Warranty
Period, TAKEX will repair or replace, at its sole option,free of charge, any defective parts returned prepaid. Please provide the model number of the products, original date of shipment and
nature of dif culty being experienced. There will be charges rendered for product repairs made after our Warranty Period has expired.
In Japan
Takenaka Engineering Co., Ltd.
83-1, Gojo-sotokan, Higashino,
Yamashina-ku, Kyoto 607-8156, Japan
Tel : 81-75-501-6651
Fax : 81-75-593-3816
http : // www. takex-eng. co. jp /
Adjustment
mode
Operation
mode
Response time
adjustment potentiometer
0.04
0.3 （sec.）
（sec.）
Response time：0.3 sec.
Walk with quick steps
Remedies
1. Turn on the power
2. Check wire
1. Turn on the power
2. Check wire
3. Remove the object
causing the reflection, or
change the place for
installation
1. Turn on the power on the
transmitter
2. Readjust angle
3. Remove obstacles.
1. Check again
2. Stabilize supply voltage
3. Remove object the
causing the shade
4. Change the place of
installation
5. Readjust
In the U.S.
In Australia
Takex America Inc.
Takex America Inc.
151, San Zeno WAY
4/15 Howleys Road, Notting Hill,
Sunnyvale, CA 94086, USA
VIC, 3168
Tel : 408-747-0100
Tel : +61 (03) 9544-2477
Fax : 408-734-1100
Fax : +61 (03) 9543-2342
http : // www. takex. com
10
SPECIFICATION
Type
Model
Protection distance
Max. arrival distance
Microwave
Detection system
Response time
0.04sec. to 0.3sec. (Variable using POT)
Dry contact relay output 1C N.O. / N.C. COM.
Alarm signal
Contact action : Interruption time output
Contact capacity : 30V (AC/DC) 0.25A or less
Supply voltage
Power consumption
Tamper signal
Alarm LED (Receiver)
Transmission LED
Green LED Lighting at signal transmission
(Transmitter)
Functions
Monitor output, Adjustment mode switch
Weight
Transmitter 36.8oz (1,050g) Receiver 38.5oz (1,100g)
Appearance
11
EXTERNAL DIMENSIONS
5.12" (130mm)
4.96" (126mm)
φ1.50" to φ1.77"
(φ38mm to φ45mm)
In the U.K.
Takex Europe Ltd.
Aviary Court, Wade Road,
Basingstoke, Hampshire. RG24 8PE, U.K.
Tel : (+44) 01256-475555
Fax : (+44) 01256-466268
http : // www. takex. com
Microwave sensor
MW-100AL
16.5ft. (5m) to 330ft. (100m)
Approx. 660ft. (200m)
24.12GHz
Microwave
12 to 28V DC
100mA
・Transmitter : 40mA
・Receiver
: 60mA
Dry contact output N.C.
Contact capacity : 30V (AC/DC) 0.1A
Red LED Lighting at alarm
Resin (Wine red)
Unit: inch (mm)
2.01"
2.36" (60mm)
(51mm)
0.17" (4.2mm)
1.57" (40mm)
φ0.79" (φ20mm)
MOUNT HOLE
No.06-016
2-φ0.16"
(2-φ4mm)
Wiring hole
1711
Advertisement
