Related Manuals for DeLonghi DEF905GEG
Summary of Contents for DeLonghi DEF905GEG
- Page 1 D E’ LO N G HI C OO KIN G INSTALLATION and SERVICE INSTRUCTIONS USE and CARE INSTRUCTIONS D EF9 05GE G D UA L F U EL C OO K ER distributed by DeLonghi Australia Pty Ltd DeLonghi New Zealand Ltd...
-
Page 3: Product Label
Dear Customer, Thank you for having purchased and given your preferen- ce to our product. The safety precautions and recommendations reported below are for your own safety and that of others. They will also provide a means by which to make full use of the fea- tures offered by your appliance. -
Page 4: Important Safety Precautions And Recommendations
IMPORTANT SAFETY PRECAUTIONS AND RECOMMENDATIONS IMPORTANT: This appliance is designed and manufactured solely for the cooking of domestic (household) food and is not suitable for any non domestic application and therefore should not be used in a commercial environment. The appliance guarantee will be void if the appliance is used within a non domestic environment i.e. - Page 5 ■ Do not use a steam cleaner because the moisture can get into the appliance thus make it unsafe. ■ Do not touch the appliance with wet or damp hands (or feet). ■ Do not use the appliance whilst in barefoot. ■...
- Page 6 ■ WARNING: Unattended cooking on a hob with fat or oil can be dangerous and may result in fire. NEVER try to extinguish a fire with water, but switch off the appliance and then cover flame e.g. with a lid or a fire blanket. ■...
- Page 7 from the oven whilst hot. ■ Do not hang towels, dishcloths or other items on the appliance or its handle – as this could be a fire hazard. ■ Clean the oven regularly and do not allow fat or oils to build up in the oven base or tray.
- Page 8 MOVING THE COOKER Figure 1 WARNING: When raising cooker to upright position always ensure two people carry out this manoeuvre to prevent damage to the appliance and adjustable feet (fig. 1). WARNING - Be carefull: Do not lift the cooker by the door handle when raising to the upright position (fig.
-
Page 9: Installation
INSTALLATION CAUTION: ■ This appliance must be installed according to AS/NZS 5601.1 (latest edition). ■ This appliance must be installed in accordance with these installation instructions. ■ This appliance shall only be serviced by authorized personnel. ■ This appliance is to be installed only by an authorised person in compliance with the current electrical regulations and in observation of the instructions supplied by the manufacturer. - Page 10 CLEARANCES Installation clearances and protection of combustible surfaces shall comply with the current local regulations eg. AS/NZS5601.1 (latest edition) Gas Installations code. Installation shall comply with the dimension in fig. 4a bearing in mind that. Overhead Clearances In no case shall the clearances between the highest part of the cooker be less than 650 mm or for an overhead exhaust fan 750 mm.
-
Page 11: Fitting The Adjustable Feet
GAS AND ELECTRIC CONNECTION Dotted line showing the Figure 4b position of the cooker when installed Area for GAS and ELECTRIC connection FITTING THE ADJUSTABLE FEET The adjustable feet must be fitted to the base of the cooker before use (figs. 5, 6). Rest the rear of the cooker on a piece of the polystyrene packaging exposing the base for the fitting of the feet. -
Page 12: Fixing The Backguard
FIXING THE BACKGUARD Before installing the cooker, assemble the backguard “C” (fig. 8). ■ The backguard “C” can be found packed at the rear of the cooker. ■ Before assembling remove any protective film/adhesive tape. ■ Remove the two spacers “A” and the screw “B” from the rear of the cooktop. ■... - Page 13 ANTI-TILT BRACKET Figure 9 Important! To restrain the appliance and prevent it 900 mm 900 mm tipping accidentally, fit a bracket to its rear to fix it securely to the wall. Make 4 5 0 sure you also fit the supplied lock pin to 4 5 0 4 5 0 4 5 0...
-
Page 14: Gas Supply
GAS SUPPLY ■ The connection must be performed by an authorised person according to the relevant standards. ■ Before connecting the appliance to the gas main, mount the brass conical adaptor onto the gas inlet pipe, upon which the gasket has been placed (figs. 12a - 12b). Conical adaptor and gasket are supplied with the appliance (packed with conversion kit for use with Natural gas or ULPG). -
Page 15: Natural Gas
Gas connection for Gas connection for NATURAL GAS ULPG Gas inlet pipe Gas inlet pipe Nipple Nipple Gasket Gasket Brass conical adaptor Test Brass conical adaptor (Thread tight: use point (Thread tight: use suitable seal) suitable seal) Test point adaptor Gas regulator Test point... - Page 16 Customer Service Centre should be called to obtain the nearest authorized Delonghi Service Agent. CONVERSION PROCEDURE (TO CONVERT TO NATURAL GAS OR TO ULPG) REPLACING THE INJECTORS This appliance is suitable for use with Natural gas or ULPG (check the “gas type”...
- Page 17 ■ ” Using a 10 mm box spanner, unscrew the injector “U (indicated by the arrow in fig. 17) and replace with a new injector selected in accordance with the “TABLE FOR THE CHOICE OF THE INJECTORS” (see following table - page 21); then replace the burner repeating the above steps in reverse order.
- Page 18 Affix to the rear of the appliance, in proximity of the gas inlet connections, the warning label (supplied with the conversion kit) stating that the cooker has been converted for use with ULPG / Natural gas. IMPORTANT ■ If the cooker is suitable for use with Natural gas and must be converted for use with ULPG, before connecting to the gas mains remove the appliance gas regulator and replace with test point adaptor (see figs.
- Page 19 Figure 18 Figure 19...
- Page 20 AIR RING ON OVEN BURNER The air ring position is fixed (fully open) for both Natural Gas and ULPG. IMPORTANT: NEVER remove the fixing rivet to modify the position of the air ring on the oven burner (fig. 20). Figure 20 Air ring Rivet NO !
-
Page 21: Lubrication Of The Gas Taps
TABLE FOR THE CHOICE OF THE INJECTORS Natural gas ULPG Test Point Pressure 2.75 [kPa] BURNER Auxiliary (A) 0.85 3.60 0.53 3.60 Semi-rapid (SR) 1.12 6.30 0.70 6.30 Rapid (R) 1.45 10.30 0.91 10.80 Triple ring (TR) 1.60 12.70 0.95 11.90 Oven 1.90... -
Page 22: Using The Oven For The First Time
USE AND CARE CAUTION: ■ This appliance must be used only for the task it has explicitly been designed for, that is for domestic cooking of foodstuffs. Any other form of usage is to be considered as inappropriate and therefore dangerous. ■... -
Page 23: Grease Filter
■ Slide off the wire racks. ■ Let the oven cool down, switch off the electrical supply, then clean the inside of the oven with a cloth soaked in water and neutral detergent and dry thoroughly. GREASE FILTER ■ A special screen is provided at the back of the oven to catch grease particles, mainly when meat is being roasted. -
Page 24: Control Panel
CONTROL PANEL Figure 25 OVEN GRILL & LIGHT T° FAN & OVEN LIGHT Controls description Front right burner control knob Rear right burner control knob Central burner control knob Rear left burner control knob Front left burner control knob 60’ alarm control knob Gas oven thermostat control knob Oven light and fan motor control knob Electric grill and light control knob... -
Page 25: Gas Burners
GAS HOB Figure 26 GAS BURNERS Natural Gas ULPG MJ/h MJ/h 1. Auxiliary burner (A) 2. Semi-rapid burner (SR) 3. Rapid burner (R) 10.3 10.8 4. Triple ring burner (TR) 12.7 11.9 Notes: ■ The electric ignition is incorporated in the knobs. ■... - Page 26 GAS BURNERS (Auxiliary, Semi-rapid, Rapid and Triple ring) Gas flow to the burners is adjusted by turning the knobs (illustrated in fig. 27a) which control the valves. Turning the knob, so that the indicator on itself points to the symbols printed on the control panel, achieves the following functions: Knob AUXILIARY, SEMI-RAPID...
- Page 27 Customer Service center your nearest Authorized Delonghi Service Agent. In the case of a mains failure light the burner with a match or lighted taper. Adjust the gas valve to the desired position. If the burner flames should go out for some reason, the safety valve will automatically stop the gas flow.
- Page 28 CHOICE OF BURNER The burner must be chosen according to the diameter of the pans and energy required. For optimum efficiency uso a wok or pan no smaller than 230 mm diameter. Figure 28 do not use pans with concave or convex bases Burners Pan diameter Auxiliary...
- Page 29 CORRECT USE OF TRIPLE-RING BURNER ■ The flat-bottomed pans are to be placed directly onto the pan-support. ■ To use the WOK, you must place the wok stand in the CORRECT position as shown in figs. 30 - 31. IMPORTANT The special grille for wok pans (fig.
-
Page 30: Operating Principles
COOKING WITH FAN ASSISTED OVEN OPERATING PRINCIPLES Attention: The oven door becomes Heating and cooking in the FAN ASSISTED very hot during operation. OVEN are obtained in the following ways: Keep children away. by normal convection The heat is produced by the lower gas burner. -
Page 31: Oven Burner
OVEN BURNER The gas flow to the burner is regulated by a OVEN thermostat which allow to maintain the oven temperature constant. The control of the temperature is assured by a thermostatic probe positioned inside the oven. The probe must be always kept in its housing, in a clean condition, as an incorrect position or encrustment may cause an alteration in the control of the temperature. - Page 32 IGNITION OF THE OVEN BURNER Gently close the oven door and set the oven control knob to the required ATTENTION: Never turn the control temperature. knob before opening the oven door. If the flame extinguishes for any reason, To light the oven burner operate as follows: the safety valve will automatically shut off Open the oven door to the full the gas supply to the burner.
- Page 33 ELECTRIC GRILL To switch on the grill turn the control knob clockwise and set the knob to the required For safety reasons, it is not allowed to temperature between minimum use the oven burner and the electric grill maximum position (fig. 35). together, at the same time.
-
Page 34: Oven Light
FAN MOTOR “COMBI-GAS” FAN & OVEN LIGHT The fan motor is designed to distribute throughout the oven the heat generated by the oven gas burner or the electric grill. The fan motor can also be used without the gas burner or the electric grill (without heating) to defrost frozen foods. - Page 35 COOKING WITH FAN ASSISTED GAS OVEN - OVEN BURNER AND FAN MOTOR - After the ignition of the oven gas burner, gently close the oven door and switch on the fan motor. Before introducing the food, preheat the oven to the desired temperature. For a correct preheating operation, it is advisable to remove the tray from the oven and introduce it together with the food, when the oven has reached the desired temperature.
- Page 36 COOKING WITH FAN ASSISTED GRILL - ELECTRIC GRILL AND FAN MOTOR - Switch on the electric grill and the fan motor and let the oven to preheat for about 5 minutes with the door closed. The heat is mainly diffused by radiation and the fan then distributes it throughout the oven. Introduce the food to be cooked positioning the rack as close to the grill as possible;...
- Page 37 KEEP WARM OR SLOW HEATING - ELECTRIC GRILL WITH FAN MOTOR - Switch on the electric grill and the fan motor. Turn the grill control knob to the “Min” minimum position (figs. 35, 42). The heat is diffused throughout the oven by forced convection. Grilling with the oven door closed.
-
Page 38: Minute Counter
HOW TO USE THE 60 MINUTES MECHANICAL ALARM MINUTE COUNTER The minute counter is a timed acoustic warning device which can be set for a maximum of 60 minutes. The knob (fig. 44) must be rotated clockwise as far as the 60 minute position and then set to the required time by rotating it anticlockwise. -
Page 39: Cleaning And Maintenance
CLEANING AND MAINTENANCE Maintenance Period Description ■ Daily Clean gas cooktop as per instructions below ■ Remove burner caps, burner rings & base and clean using non abrasive detergent & rinse in cold water & dry thoroughly before replacing back on hob Monthly ■... - Page 40 GAS TAPS If the gas taps are not working properly, call our Customer Service Centre to obtain the nearest Authorized Delonghi Service Agent. GRILL HEATING ELEMENT ■ The heating element is self-cleaning and does not require maintenance.
- Page 41 Figure 45a Figure 45b Figure 45c Figure 45e Figure 45d...
-
Page 42: Replacing The Oven Light
REPLACING THE OVEN LIGHT Figure 46 WARNING: Ensure the appliance is switched off and disconnected from the electrical power supply before replacing the lamp to avoid the possibility of electric shock. ■ Let the oven cavity and the heating elements to cool down. ■... - Page 43 REMOVING AND REPLACING THE INNER DOOR GLASS PANE FOR CLEANING If you wish to clean the inner glass of the door, make sure you follow the precautions and instructions very carefully. Replacing the glass pane and the door incorrectly may result in damage to the appliance and may void your warranty.
-
Page 44: Removing The Oven Door
REMOVING THE OVEN DOOR The oven door can easily be removed as follows: ■ Open the door to the full extent (fig. 49a). ■ Open the lever “A” completely on the left and right hinges (fig. 49b). ■ Hold the door as shown in fig. 49d. ■... - Page 45 REFIT THE DOOR ■ Hold the door firmly (fig. 50a). ■ Insert the hinge tongues into the slots, making sure that the groove drops into place as shown in the figure 50b. ■ Open the door to its full extent. ■...
- Page 46 CLEANING THE PANES OF GLASS The oven door is fitted with no. 2 panes: ■ no. 1 outside; ■ no. 1 inner. To clean the panes on both sides it is necessary to remove the inner pane as follows. REMOVING THE INNER PANE OF GLASS Lock the door open: Figure 51a...
- Page 47 AFTER CLEANING, REPLACE THE INNER GLASS PANE When replacing the inner glass pane, make sure that: ■ You replace the pane correctly, as shown. The pane must be in the position described below in order to fit into the door and to ensure that the Figure 52a oven operates safely and correctly.
-
Page 48: Service And Maintenance
SERVICING THE APPLIANCE Service may be obtained by contacting our Customer Service Centre to locate the nearest Authorised Delonghi Service Agent: Servicing shall be carried out only by authorized personnel. The appliance shall not be modified. -
Page 49: Electric Diagram
ELECTRIC DIAGRAM Figure 53 ELECTRIC DIAGRAM KEY Oven light/fan motor switch Thermal overload (operation of cooling fan motor) Grill element switch Grill thermostat pilot lamp Grill security switch Oven fan motor Grill heating element Ignition switches group Oven lamp Ignition coil Grill thermostat Terminal block Thermal overload... - Page 52 .au ww w.de lo nghi.co .nz...