Appliances - KERUI G19 Operation Instruction Manual

The door contact should be installed on the movable door. Firstly, clean the
corresponding position, and take out wireless door contact , then put on the
double faced adhesive. The installation should note the items below:
1.The door sensor part A (transmitter) and part B (magnet) should be installed
separately, that is, A on fixed door frame and B on movable door. ( the side with
lights of transmitter should correspond with the magnet )
2. A and B should in the same vertical line and the distance between A and B
should not greater than 1 cm.
3. After the installation, the indicator light flashes for 1s as the door open, that
means the door sensor is installed successfully.
4.The indicator light lit for 1 second, means alarm. The indicator in constant light
is a suggestion of power lack.
5.A, B can also be reinforced by screws, (A: remove the bottom cover, then screw
in the bottom, buckle the cover to the bottom; B can be directly fixed on the
screw back.)
9.2 Installation and Use of PIR Motion Detector
overlook
Before use, make sure the power switch of PIR motion sensors is ON. Installation
height is about 2.2 meters above ground and it should be installed in the corner
of the room to get the best detection range and should form a certain angle with
the indoor walking line at the same time ( the 90 degree angle with people walking
direction is best for detection)
Installation:
Remove the supplied mounting bracket, press the bracket to the slot in the detector
ground
side view
P31
bottom. Find the base and reinforce it with two screws in the wall. Press the PIR
with bracket into the center hole of base. and then adjust the best angle of
detecting. (This method is suitable for project installation)
Attention:
1.The detector should not face the outside of window directly.
2. Within coverage of detection, there should be no any big objects for obstruction.
3. There should be no two infrared detectors in the same space as they will possibly
intervene with each other.
4.Avoid facing window, cooling or warming machines, stoves, or other appliances
that cause the temperature changing sharply and thus cause false alarm.
5. Infrared detector are indoor use and couldn't be used outdoor.
X. Troubleshooting
Troubleshooting
Reasons
1. no arming
2. alarm phone unset
3.parts improperly installed,
1.No dial for alarm
distance too far
4. code no match
1.No SIM card
2.PIN code is set for SIM card
2.Host can't read 3.bad GSM signal
SIM card or don't
4.SIM card has scratched copper
dial and text to
5.Alarm phone number unset
preset alarm
6.Message Alarm number unset
phone number
7.Card balance is insufficient or out
of date
8.Message function is OFF
3.Can't remote operate
1.input wrong password
4.no ISD recorded voice
ISD Voice prompt un-recorded
prompt when alerting
1.coding unmatched with the host
2.insufficient power
5.remote controller
3.batter y pieces poor contact or
not work
corroded
4.unmatched with host
1.coding unmatched with the host
2.insufficient power
3.batter y pieces poor contact or
6.PIR sensor not work
corroded
4.unmatched with host
7, siren no sound
1.internal siren is OFF
8.The transmitter 1.a nearby emitter is sending code
2. host receiver stop work
distance for host
3.standby batter y of the host insufficient
is shortened
9.Host no Voice prompt 1 voice prompt function is OFF .
Methods
1. do arming operation
2.re-set according to the specification
3. coordinating the location of parts
4. re-coding
1、Insert SIM card
2.Cancel PIN code
3.change to a strong signal place
4.change to a normal SIM card
5.set alarm phone number
6.set message alarm number
7.charge SIM card
8.activate the message function
1.Correct password or change to
a new password or restore to factor y
default
Record it again according to user
manual
1.re-coding
2.change batter y of the same type
3.eliminating the dirt on the pieces
caused by corrosion
4.contact the local dealer to change
the matched remote controller
1. re-coding
2. change batter y of the same type
3. eliminating the dirt on the pieces
caused by corrosion
4. contact the local dealer to change
the matched remote controller
1.Open internal siren
1.find the interfering source and
eliminate it
2.post back to the factory for amendment
3.check host power whether plugged well
1 open voice prompt function .
P32