KERUI G19 Operation Instruction Manual page 6

Rfid color screen intelligent gsm network alarm system
Table of Contents

Advertisement

4.7.1 Remote Control
4.7.1.1 Study Remote Control
On accessories manage page, press key【OK】directly or number 1 to enter
remote control page. As shown in picture 4-8, there are 99 zones in the page,
press key【UP/DOWN】to select zone or input number (01-99) by keyboard ( e.g.
Study No. 1 remote control, then input 01, study No. 22 remote control, input 22),
then press key【OK】to enter remote control study page as shown in picture 4-9.
At this moment, press any key on remote controller to send a signal to host, host
sounds "di" and the number of learned remote add 1 on the screen, which means
the remote control has been programmed to the host; If there is wrong voice
prompt when pressing remote control, and it means that the remote control has
been learned to the host already and couldn't be programmed repeatedly. To
learn more remote controls, press any key on other remote controls. The host can
study as most as 99 different remote controls.
4.7.1.2 Delete Remote Control
Delete remote control in single zone: after entering remote control page, press
key【UP/DOWN】to select the zones needed to be deleted, press key【OK】, host
will pop up a small menu as shown in picture 4-10. If selecting【Edit/Add】, it can
continue to study remote control or set if there is accompany sound; if selecting
【Delete】, host will pop up a confirmation menu, select【Yes】, press key【OK】
to confirm, then all the remote controls in the zone be deleted.
Delete all remote controls: As shown in picture 4-11, there is Delete All function
at the bottom of remote control page. Press key【UP/DOWN】to select this function,
then press key【OK】, it will pop up the confirmation menu, then press key【OK】
again to delete all the remote controls in all zones.
CHINA MOBLLE
CHINA MOBLLE
16:10
Remote
Remote
1PCS
97 Zone
1 PCS
1 PCS
Sound on
01 Zone
Edit / Add
98 Zone
0 PCS
0 PCS
Sound on
02 Zone
Delete
99 Zone
0 PCS
0 PCS
Sound on
03 Zone
Delete all
Sound on
04 Zone
0 PCS
Picture 4-10
Picture 4-11
4.7.1.3 Remote Control SND Sound
As shown in picture 4-12, on remote control study page, press key【DOWN】to
select sound ON/OFF. Press 1 to select Yes, then the sound is ON in this zone; Press
2 to select No, then the sound is OFF in this zone. If the sound is ON, the external
siren would beep "di di" when using the remote control in this zone to arm/disarm.
The factor y default of the sound is ON.
Note: there are two kinds of host sirens: one is host horn siren, called built-in siren;
the other are external wired siren and wireless siren, called external siren.
4.7.2 Detector
4.7.2.1 Study Detectors
CHINA MOBLLE
16:10
16:10
01 Zone Remote
0 PCS
Sound on
Have added:
1 PCS
Total:
1
PCS
Sound on
Sound:
On
Sound on
1.On
2.Off
Picture 4-12
On accessories manage page, as shown in picture 4-7. Press key【UP/DOWN】
to select Detector, then press key【OK】or number 2 directly to enter detector
page, as shown in picture 4-13. There are 99 zones in the page, and it displays
the number of detectors learned,siren state, event code, and zone attribute in
each zone. Press key【 UP/DOWN 】to select zone or input number ( 01-99 ) by
keyboard ( e.g. Study No. 1 detector, then input 01, study No. 22 detector, input
22), then press key【OK】to enter detector study page as shown in picture 4-14.
At this moment, trigger detector to send a signal to host, host beeps "di" and the
number of learned detector add 1 on the screen, which means the detector has
been programmed to the host; If there is wrong voice prompt when triggering
detector, and it means that the detector has been learned to the host already
and couldn't be programmed repeatedly. To learn more detectors, continue to
trigger other detectors. The host can study as most as 99 different detectors.
CHINA MOBLLE
16:10
CHINA MOBLLE
Detector
01 Zone Detector
1PCS
Siren on Normal
Have added:
1 PCS
01 Zone
Thief
Total:
Siren on Normal
Please trigger detector
02 Zone
0 PCS
Thief
Sound:
Siren on Normal
03 Zone
0 PCS
Attribute:
Thief
CID eventcode:
Siren on Normal
04 Zone
0 PCS
Thief
Picture 4-13
Picture 4-14
4.7.2.2 Delete Detectors
Delete detector in single zone: after entering detector page, press key【 UP/
DOWN】to select the zones needed to be deleted, press key【OK】, host will pop
up a small menu as shown in picture 4-15. If selecting【Edit/Add】, it can continue
to study detector or set the zone attribute and event code; if selecting【Delete】 ,
host will pop up a confirmation menu, select【Yes】, press key【OK】to confirm,
then all the detectors in the zone be deleted.
Delete all detectors: As shown in picture 4-16, there is Delete All function at the
bottom of detector page. Press key【UP/DOWN】to select this function, then press
key【OK】, it will pop up the confirmation menu, then press key【OK】again to
delete all the detectors in all zones.
CHINA MOBLLE
16:10
CHINA MOBLLE
01 Zone Detector
Detector
4 PCS
Siren on Normal
Have added:
97 Zone
0 PCS
Thief
Total:
Siren on Normal
98 Zone
0 PCS
Thief
Siren:
1.On
Siren on Normal
99 Zone
1 PCS
Thief
Attribute:
CID eventcode:
Delete all
Picture 4-16
Picture 4-17
4.7.2.3 Call Alarm ON/OFF
On detector learning page, press key【DOWN】to select zone call alarm ON/OFF
as shown in picture 4-17. Press【1】to select Yes, call alarm ON; Press【2】to select
16:11
CHINA MOBLLE
16:10
Detector
1PCS
1 PCS
Siren on Normal
1 PCS
01 Zone
Thief
4 PCS
Edit / Add
Siren on Normal
02 Zone
0 PCS
0 PCS
Thief
Delete
On
Siren on Normal
03 Zone
0 PCS
Normal
Thief
Thief
Siren on Normal
04 Zone
0 PCS
Thief
Picture 4-15
CHINA MOBLLE
16:11
16:11
01 Zone Detector
Have added:
2 PCS
2 PCS
Total:
5 PCS
5 PCS
Siren:
on
On
Attrebute: Normal
2.Off
1.Normal 2.Stay 3.Smart 4.Urgent
5.Close
6.Doorbell 7.Welcome 8.Help
Normal
Thief
CID eventcode:
Thief
Picture 4-18

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents