Page 1
MANUAL Intensifier T Motorized Zoom Focus Camera HT7248TM ( Dome Camera) HTB11TM (Bullet Camera) Speco Technologies is constantly developing product improvements. We reserve the right to modify product design and specifications without notice and without incurring any obligation. Rev. 2/01/2017...
Page 2
Contents Contents ............1 ◑ Precautions ..........2, 3 ◑ Safety Instructions ........4 ◑ Package Contents ........5 ◑ Camera Installation ........6-9 ◑ Specifications ..........10-11 ◑ Camera Dimension ........12 ◑ Features ............13 ◑ OSD Menu Details ........14-32 ◑...
Precautions Do not install the camera in Do not install the camera under Do not touch the front lens of the extreme temperature conditions. unstable lighting conditions. camera. Only use the camera under conditions Severe lighting change or flicker can This is one of the most important parts of where temperatures are between cause the camera to work improperly.
Page 4
CAUTION CAUTION CAUTION RISK OF ELECTRIC SHOCK RISK OF ELECTRIC SHOCK RISK OF ELECTRIC SHOCK DO NOT OPEN DO NOT OPEN DO NOT OPEN CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER(OR BACK).
Safety Instructions Precautions for use ◑ This camera should be installed by qualified personnel only ◑ There are no user serviceable parts inside ◑ Do not disassemble this camera other than to make initial adjustments ◑ Use a UL approved regulated 24 volt AC or 12 volt DC power supply ◑...
CAMERA INSTALLATION CONNECT POWER CABLE 1. WHEN USING 12 VOLTS DC (constant voltage 500mA) P o w e r In p u t :R E D C e n te r : (+) D C 12V P owe r S upply 2.
To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. CAMERA INSTALLATION 2. HTB11TM WALL SCREW TS T1, 4X25, TH, SUS, 4EA...
TV system is switchable 'NTSC' or 'PAL' with built-in OSD. Intelligent Function ● An extraordinary technology that enables Speco Technologies TVI to become the ultimate solution by providing intelligent features based on motion detection. It also strengthens crime prevention and detection.
* MENU will be displayed on the monitor. ◆ PRESET MODE : Preset is provided to maximize user convenience. ( PRESET : Indoor // Outdoor // Low light // Hallway // Lobby // Elevator ) SPECO TECH 1.PRESET INDOOR 2.MAIN SETUP 3.EXIT...
Page 19
* The Set Up menu will be displayed on the monitor. MENU 1.2MOTOR 2.LENS 3.EXPOSURE 4.WHITE BAL AUTO 5.BACKLIGHT 6.SPECO DNR MIDDLE 7.DAY&NIGHT AUTO 8.IMAGE 9.MOTION 10.SYSTEM RETURN 2. Move and select the required function using the Up and Down button.
Page 20
1. Move the triangular indicator to 2MOTOR using the Up and Down buttons on the Set Up menu screen. 2. Select the desired lens type by pressing the Left of Right button. MENU 1.2MOTOR 2.LENS 3.EXPOSURE 4.WHITE BAL AUTO 5.BACKLIGHT 6.SPECO DNR MIDDLE 7.DAY&NIGHT AUTO 8.IMAGE 9.MOTION 10.SYSTEM RETURN 2MOTOR...
Page 21
1. Move the triangular indicator to LENS using the Up and Down buttons on the Set Up menu screen. 2. Select the desired lens type by pressing the Left or Right button. MENU 1.2MOTOR 2.LENS 3.EXPOSURE 4.WHITE BAL AUTO 5.BACKLIGHT 6.SPECO DNR MIDDLE 7.DAY&NIGHT AUTO 8.IMAGE 9.MOTION 10.SYSTEM RETURN - 20 -...
Page 22
1. On the Set Up menu, Select EXPOSURE by using the Up or Down button. MENU 1.2MOTOR 2.LENS 3.EXPOSURE 4.WHITE BAL AUTO 5.BACKLIGHT 6.SPECO DNR MIDDLE 7.DAY&NIGHT AUTO 8.IMAGE 9.MOTION 10.SYSTEM RETURN 2. Select the desired shutter mode by pressing the Left or Right button.
1. Move the triangular indicator to WHITE BAL on the SETUP menu screen using the Up and Down button. 2. Select the desired mode by using the left or Right button. MENU 1.2MOTOR 2.LENS 3.EXPOSURE 4.WHITE BAL AUTO 5.BACKLIGHT 6.SPECO DNR MIDDLE 7.DAY&NIGHT AUTO 8.IMAGE 9.MOTION 10.SYSTEM RETURN - 22 -...
Page 24
◆ AUT0 : Use this mode when the color temperature is from 2,500k to 9,500k. ◆ AWB : The function to search for the color which is matched well with the ambient environment. ◆ AWC→SET : After letting camera focus on the blank white paper to the best condition of current lighting environment, press the SET button.
Page 25
1. Move the triangular indicator to BACKLIGHT on the SETUP menu screen using the Up and Down button. 2. Select the desired mode by using the left or Right button. MENU 1.2MOTOR 2.LENS 3.EXPOSURE 4.WHITE BAL AUTO 5.BACKLIGHT 6.SPECO DNR MIDDLE 7.DAY&NIGHT AUTO 8.IMAGE 9.MOTION 10.SYSTEM RETURN ◆ Off : Deactivated status.
Page 26
◆ BLC : This function is used to counterbalance the screen image by increasing the brightness so that a subject which appears dark due to a strong backlight can be displayed in more detail. If you select BLC, a submenu appears where you can make finer adjustments. - H-POS/V-POS/H-SIZE/V-SIZE : Define the position and size of the area of interest by changing the position &...
Page 27
SPECO DNR This function is used to improve the picture quality by filtering the noise which is generated under low brightness conditions. You can set different levels here. 1. Move the triangular indicator to DNR by using the Up and Down button.
Page 28
◆ AUTO : Automatically, It shifts into the color mode in the bright environment and the B/W mode in the low light condition. It can adjust the delay time, starting brightness and end brightness according to the ambient conditions by pressing the Set button. DAY&NIGHT SMART IR |IIIIIIIIIIIIII| 0...
Page 29
- DELAY [LOW/MIDDLE/HIGH] : Set the delay time for switching between color and B/W . IMAGE When selecting, the following submenu will appear. MENU 1.2MOTOR 2.LENS 3.EXPOSURE 4.WHITE BAL AUTO 5.BACKLIGHT 6.SPECO DNR MIDDLE 7.DAY&NIGHT AUTO 8.IMAGE 9.MOTION 10.SYSTEM RETURN Here you can optimize the image quality by adjusting different options. IMAGE...
Page 30
- D-ZOOM : You can use the digital zoom with x1~x8 magnification. The higher the digital zoom magnification is, the lower the resolution is. - ACE [LOW/MIDDLE/HIGH] : Intelligent lighting level control to overcome even strong backlight conditions. - DEFOG [ON, OFF] : This function helps to recognize the object in a dusty weather condition. ON, a submenu appears where you can make finer adjustments.
Page 31
This function is used to detect moving objects in the monitored area. When choosing ON, the following submenu will appear where you can adjust the settings for the MOTION function. MENU 1.2MOTOR 2.LENS 3.EXPOSURE 4.WHITE BAL AUTO 5.BACKLIGHT 6.SPECO DNR MIDDLE 7.DAY&NIGHT AUTO 8.IMAGE 9.MOTION 10.SYSTEM RETURN MOTION...
Page 32
2.LENS IMAGE RANGE USER 3.EXPOSURE OUTPUT MODE 1080P 4.WHITE BAL AUTO COLOR SPACE HD-CbCr 5.BACKLIGHT FRAME RATE 30 FPS 6.SPECO DNR MIDDLE CVBS NTSC 7.DAY&NIGHT AUTO LANGUAGE 8.IMAGE COLOR BAR 9.MOTION RETURN 10.SYSTEM RETURN - COM. : This menu is used for RS-485 communication. Users are able to select CAM ID(0~255) and BAU D RATE (2400/4800/9600/57600/115200).
Page 33
- IMAGE RANGE [FULL/COMP/USER] : Adjust the rate of YC signal to 100%(FULL), 75%(COMP) or 100%~75%(USER). - OUTPUT MODE [720P/720P CROP/1080P] : Choose output type. - COLOR SPACE [YUV/SD-CBCR/HD-CBCR] : Select different color settings for a warmer or a colder image. - FRAME RATE [25 FPS/30 FPS] : Choose a frame rate.
Trouble Shooting ● PROBLEM POSSIBLE CAUSE FCheck the power cable, power supply output and video Northing appears on connection between the camera and monitor. the screen. FAre the camera lens or the lens glass dirty? Clean the lens / glass with a soft clean cloth. The image on the FAdjust the monitor controls, as required.