Related Manuals for Aaeon AOP-8060
Summary of Contents for Aaeon AOP-8060
- Page 1 A A E O N O p e r a t o r P a n e l A O P - 8 0 6 0 AOP-8060 SiS 550 SoC 200MHz Processor Based Fanless Operator Panel PC with 5.7” STN LCD AOP-8060 Manual 1 Sep. 2004 AOP-8060 Series User Manual...
-
Page 2: Copyright Notice
AAEON, assumes no liabilities resulting from errors or omissions in this document, or from the use of the information contained herein. AAEON reserves the right to make changes in the product design without notice to its users. AOP-8060 Series User Manual... -
Page 3: Acknowledgments
UMC is a trademark of United Microelectronics Corporation. SMI is a trademark of Silicon Motion, Inc. Creative is a trademark of Creative Technology LTD. All other product names or trademarks are properties of their respective owners. AOP-8060 Series User Manual... -
Page 4: Packing List
A O P - 8 0 6 0 Packing List Before you begin installing your card, please make sure that the following materials have been shipped: • AOP-8060 series Fanless Panel PC • CompactFlash storage card • PS/2 Y type keyboard / mouse cable •... - Page 5 Packing: please carry the unit with both hands, handle with care Maintenance: to properly maintain and clean the surfaces, use only approved products or clean with a dry applicator CompactFlash: Turn off power before inserting or removing CompactFlash storage card. AOP-8060 Series User Manual...
-
Page 6: Safety & Warranty
12. Never pour any liquid into an opening. This may cause fire or electrical shock. 13. Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel. AOP-8060 Series User Manual... - Page 7 EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER, DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS. DISCLAIMER: This set of instructions is given according to IEC 704-1. AAEON disclaims all responsibility for the accuracy of any statements contained herein. AOP-8060 Series User Manual...
-
Page 8: Table Of Contents
Safety & Warranty ..............6 General Information................9 Introduction................10 Specification .................11 Dimension................16 Hardware Installation..............17 Panel Mount Installation............18 Digital I/O Connector (CN14) ..........20 COM1 Connector (CN9) ............21 COM 2 Connector (CN10) ...........21 Win CE Installation...............22 Win CE Installation Steps .............23 AOP-8060 Series User Manual... -
Page 9: General Information
A A E O N O p e r a t o r P a n e l A O P - 8 0 6 0 Chapter General Information AOP-8060 Series User Manual... -
Page 10: Introduction
A O P - 8 0 6 0 Introduction The AOP-8060 operator panel is a SiS Low power processor computer that is designed to serve as a human machine interface (HMI). It is a PC-based system with 5.7" color STN LCD display, on-board Ethernet controller, multi-COM port interfaces and an audio controller. -
Page 11: Specification
1 digital I/O (support up to 8 in and 8 out) • Storage Disk Drive Type II CompactFlash slot • OS Support Windows CE Net 4.2, Embedded Linux (optional) Mechanical • Construction Plastic chassis (IP65 certified front panel) AOP-8060 Series User Manual... - Page 12 Input: +12V ~24V • Display Type 5.7” color STN LCD • Max. Resolution 320 x 240 • Max. Colors • Dot Size 0.12mm x 0.36mm • Luminance 200 cd/m2 (TYP.) • ° Viewing Angle 90° (H) AOP-8060 Series User Manual...
- Page 13 AAEON qualify the LCD panel following industry standard: total 7 dead pixels on a screen or if there are 3 within 1 inch square area of each other on the display.
- Page 14 A A E O N O p e r a t o r P a n e l A O P - 8 0 6 0 IP65 certified front panel with touch screen Base-T Ethernet connector Parallel Port DC inlet PS/2 keyboard & Mouse Ground Line out ~24V Input Dual USB ports AOP-8060 Series User Manual...
- Page 15 A A E O N O p e r a t o r P a n e l A O P - 8 0 6 0 VESA 75mm screw holes RS-232 port RS-232/422/485 25-pin port Digital I/O CompactFlash Type II socket AOP-8060 Series User Manual...
-
Page 16: Dimension
A A E O N O p e r a t o r P a n e l A O P - 8 0 6 0 Dimension AOP-8060 Series User Manual... -
Page 17: Hardware Installation
A A E O N O p e r a t o r P a n e l A O P - 8 0 6 0 Chapter Hardware Installation AOP-8060 Series User Manual... -
Page 18: Panel Mount Installation
Step 3: Fix the monitor with the mounting set by screwing it. Step 4: You’ve completed the preliminary when the mounting set is tightened. Next, repeat the steps and tighten all mounting set around the monitor until the monitor is firmly mounting on the wall. AOP-8060 Series User Manual... - Page 19 A A E O N O p e r a t o r P a n e l A O P - 8 0 6 0 Complete Illustration AOP-8060 Series User Manual...
-
Page 20: Digital I/O Connector (Cn14)
Input 1 / Output 1 Input 2 / Output 2 Input 3 / Output 3 Input 4 / Output 4 Input 5 / Output 5 Input 6 / Output 6 Input 7 / Output 7 Input 8 / Output 8 AOP-8060 Series User Manual... -
Page 21: Com1 Connector (Cn9)
DTR1 DSR1 RTS1 CTS1 COM 2 Connector (CN10) Signal Signal N.C. N.C. N.C. N.C. N.C. N.C. DTR2 N.C. 485TX+ 485TX+ N.C. N.C. TXD2 RXD2 RTS2 CTS2 DSR2 N.C. DCD2 N.C. 485RX- 485TX- N.C. D-SUB 25 Connector AOP-8060 Series User Manual... -
Page 22: Win Ce Installation
A A E O N O p e r a t o r P a n e l A O P - 8 0 6 0 Chapter Win CE Installation AOP-8060 Series User Manual... -
Page 23: Win Ce Installation Steps
Copy all files under the OS folder in the CD (including autoexec. bat, config. sys, fdxms. sys, loadcepc. exe and nk. bin) to CF card Insert your CF card to AOP-8060. Reboot up your CF card to execute Win CE.